Search
Advanced Search
of the following are true
(
)

Results

Items (211,565)
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
Engine Power Test Code Committee
This SAE Standard provides general and dimensional specifications for beaded ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are designed to be used with hoses that are intended to be retained by hose clamps. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail
Hydraulic Hose and Hose Fittings Committee
This SAE Information Report provides general information for installing and tightening fluid conductors and connectors. Following these guidelines, with the consistent proper use of torque wrenches, tightening procedures, and correct torque levels, will result in diminishing leaks and improving service life by avoiding hose twisting, tube binding, false torque, and improper joint closures. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, this report should not be used as a “standard” nor a “specification,” and the values shown should not be construed as “guaranteed” minimums, maximums, or absolutes. This document is an information report to help users by gathering available information from the various connector standards and publishing the information in one source for easy retrieval and applied common usage. This SAE Information Report is primarily intended for mobile/stationary industrial equipment applications. Aircraft
Hydraulic Tube Fittings Committee
This SAE Information Report is intended to provide design guidance in the selection of steel tubing and related tube fittings for general hydraulic system applications. The information presented herein is based on tubing products which conform to SAE and ISO standards listed in the reference section. All pressure rating data found in the charts included in this document are calculated per the formula found in ISO 10763 and the main body of this document
Metallic Tubing Committee
This SAE Recommended Practice applies to electrically powered hydraulic or mechanically operated platform devices which permit a person seated in a manual or powered wheelchair to enter or exit a personally licensed vehicle. The minimum performance and durability requirements are specified for satisfactory installation of wheelchair lifting devices in a personally licensed vehicle to be used by a person seated in a wheelchair to be lifted from the ground plane to the vehicle floor level in a reliable and safe manner
Adaptive Devices Standards Committee
This SAE Aerospace Recommended Practice (ARP) establishes methods for testing airframe rolling element bearings. The purpose of ARP5483 and its associated slash sheets is to document test methods commonly used to evaluate airframe bearings. These test methods may be referenced in standards, purchase orders, etc. when the test is deemed appropriate to the intended use of the bearing by the end user of the bearing. These test methods are not intended to encompass every conceivable requirement for an airframe bearing. The end user of the bearing must exercise engineering judgment to determine the most appropriate standard and/or nonstandard tests for the application
ACBG Rolling Element Bearing Committee
This standard covers the requirements for nonseparable antifriction roller bearings
ACBG Rolling Element Bearing Committee
This SAE Standard covers normalized electric-resistance welded, cold-drawn, single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, forming, and brazing. In an effort to standardize within a global marketplace and ensuring that companies can remain competitive in an international market it is the intent to convert to metric tube sizes which will: Lead to one global system Guide users to preferred system Reduce complexity Eliminate inventory duplications
Metallic Tubing Committee
This SAE Aerospace Recommended Practice (ARP) establishes safety recommendations for lavatories in transport category airplanes
S-9B Cabin Interiors and Furnishings Committee
This SAE Aerospace Standard (AS) provides the minimum design and performance requirements for individual, inflatable life preservers, divided into six categories: “Adult,” “Adult-Child,” “Child,” “Infant-Small Child,” “Adult-Child-Infant-Small Child,” and “Demonstration
S-9A Safety Equipment and Survival Systems Committee
In order to compare test results obtained from different crash test facilities, standardized coordinate systems need to be defined for crash test dummies, vehicle structures, and laboratory fixtures. In addition, recorded polarities for various transducer outputs need to be defined relative to positive directions of the appropriate coordinate systems. This SAE Information Report describes the standardized sign convention and recorded output polarities for various transducers used in crash testing
Safety Test Instrumentation Standards Committee
The recommendations in this SAE Information Report apply to structural integrity, performance, driveability, and serviceability of personally licensed vehicles not exceeding 10 000 lb GVWR. While many of these recommendations may have application to other vehicles, such as those used in paratransit operations, the contents of this document are not directed at these types of vehicles
Adaptive Devices Standards Committee
These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries
Fasteners Committee
The SAE system of designating steels, described in SAE J402, classifies and numbers them according to chemical composition. In the case of the dent resistant, high strength and ultra high strength steels in SAE J2340, advanced high strength steels described in SAE J2745, and the high strength steels in SAE J1442 and the high-strength carbon and alloy die drawn steels in SAE J935, minimum mechanical property requirements have been included in the designations. In addition, hardenability data on most of the alloy steels and some of the carbon steels will be found in SAE J1268
Metals Technical Committee
This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies
Fasteners Committee
This SAE Standard covers the mechanical and quality requirements for two grades of carbon steel, slotted, and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3
Fasteners Committee
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties
Fasteners Committee
This Technical Information Report defines the proprietary diagnostic communication protocol for ABS or VSA ECU (Electronic Control Unit) implemented on some Honda vehicles. This protocol does not apply to all Honda vehicles. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an enhanced SAE J2534 interface. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an enhanced SAE J2534 interface
Vehicle E E System Diagnostic Standards Committee
All carbon and alloy H-band steels are shown, along with their corresponding minimum and maximum hardenability limits, for which sufficient hardenability data have been established and for grades which use the standard end-quench test. As hardenability data are accumulated for other grades, this SAE Standard will be revised to include such grades
Metals Technical Committee
This SAE Recommended Practice is applicable to all E/E systems on MD and HD vehicles. The terms defined are largely focused on compression-ignited and spark-ignited engines. Specific applications of this document include diagnostic, service and repair manuals, bulletins and updates, training manuals, repair data bases, under-hood emission labels, and emission certification applications. This document focuses on diagnostic terms, definitions, abbreviations, and acronyms applicable to E/E systems. It also covers mechanical systems which require definition. Nothing in this document should be construed as prohibiting the introduction of a term, abbreviation, or acronym not covered by this document. The use and appropriate updating of this document is strongly encouraged. Certain terms have already been in common use and are readily understood by manufacturers and technicians, but do not follow the methodology of this document. These terms fall into three categories: a Acronyms that do not
Truck and Bus Control and Communications Network Committee
Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. Information presented here can be used in preliminary design estimates of fatigue life, the selection of materials and the analysis of service load and/or strain data. The data presented are for the “low cycle” or strain-controlled methods for predicting fatigue behavior. Note that these methods may not be appropriate for materials with internal defects, such as cast irons, which exhibit different tension and compression stress-strain behavior
Materials, Processes and Parts Council
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations
Fasteners Committee
This SAE Information Report describes the processing and fabrication of carbon and alloy steels. The basic steelmaking process including iron ore reduction, the uses of fluxes, and the various melting furnaces are briefly described. The various types of steels: killed, rimmed, semikilled, and capped are described in terms of their melting and microstructural differences and their end product use. This document also provides a list of the commonly specified elements used to alloy elemental iron into steel. Each element’s structural benefits and effects are also included. A list of the AISI Steel Products Manuals is included and describes the various finished shapes in which steel is produced
Metals Technical Committee
This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in ASME B 18.6.4, Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws
Fasteners Committee
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall
Fasteners Committee
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications
Fasteners Committee
This Technical Information Report defines the diagnostic communication protocol Keyword Protocol 1281 (KWP1281). This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECUs, in which a KWP1281 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the KWP1281 protocol in enough detail to support the requirements necessary to implement the communication protocol in an SAE J2534 interface device
Vehicle E E System Diagnostic Standards Committee
This SAE Information Report is intended to provide a guide to mechanical and machinability characteristics of some SAE steel grades. The ratings and properties shown are provided as general information and not as requirements for specifications unless each instance is approved by the source of supply. The data are based on resources which may no longer be totally accurate. However, this report is retained as a service in lieu of current data
Metals Technical Committee
This top-level document provides a general overview of the SAE J1939 network and describes the subordinate document structure. This document includes definitions of terms and abbreviations which are used among the various SAE J1939 subordinate documents
Truck and Bus Control and Communications Network Committee
SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems
Hydraulic Hose and Hose Fittings Committee
This SAE Aerospace Standard (AS) covers 6-point and 12-point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box end and flare nut wrenches, combination open end and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) non-distorting usage; (b) possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 and ISO 8434-2; and (c) transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes
EG-1B Hand Tools Committee
This SAE Recommended Practice supersedes SAE J1930 MAR2017 and is technically equivalent to ISO 15031-2. This document is applicable to all light-duty gasoline and diesel passenger vehicles and trucks, and to heavy-duty gasoline vehicles. Specific applications of this document include diagnostic, service and repair manuals, bulletins and updates, training manuals, repair databases, underhood emission labels, and emission certification applications. This document should be used in conjunction with SAE J1930DA Digital Annexes, which contain all of the information previously contained within the SAE J1930 tables. These documents focus on diagnostic terms applicable to electrical/electronic systems, and therefore also contain related mechanical terms, definitions, abbreviations, and acronyms. Even though the use and appropriate updating of these documents is strongly encouraged, nothing in these documents should be construed as prohibiting the introduction of a term, abbreviation, or
Vehicle E E System Diagnostic Standards Committee
This SAE Recommended Practice describes a unified numbering system (UNS) for metals and alloys which have a "commercial standing" (see 6.1), and covers the procedure by which such numbers are assigned. Section 2 describes the system of alphanumeric designations or "numbers" established for each family of metals and alloys. Section 3 outlines the organization established for administering the system. Section 4 describes the procedure for requesting number assignment to metals and alloys for which UNS numbers have not previously been assigned
Metals Technical Committee
Items per page:
1 – 50 of 211565