Search
Advanced Search
of the following are true
(
)

Results

Items (212,033)
Ancillary Deicing/Anti-Icing InformationAIR8468 (Current)01/10/2025
This manual contains information regarding aircraft deicing/anti-icing surfaces and areas
G-12M Methods Committee
Information Report
Superfinishing of HVOF Applied Tungsten Carbide CoatingsAMS2452 (Current)01/09/2025
This specification covers requirements for the superfinishing of High Velocity Oxygen/Fuel (HVOF) applied tungsten carbide thermal spray coatings
AMS B Finishes Processes and Fluids Committee
Material Specification
Metallic WhiskersAIR4129A (Current)01/09/2025
This AIR presents an abbreviated review of the metallurgical phenomena known as whiskers. It is not all encompassing; rather, it is intended to introduce the design engineer to the technical issues of metallic whiskers, their formation, and the potentially dangerous problems they can cause
AMS B Finishes Processes and Fluids Committee
Information Report
Aerospace - Evaluation of Particulate Contamination in Hydraulic Fluid - Membrane ProcedureARP4285A (Current)01/09/2025
This SAE Aerospace Recommended Practice (ARP) establishes a method for evaluating the particulate matter extracted from the working fluid of a hydraulic system or component using a membrane. The amount of particulate matter deposited on the membrane due to filtering a given quantity of fluid is visually compared against a standard membrane in order to provide an indication of the cleanliness level of the fluid
A-6C1 Fluids and Contamination Control Committee
Recommended Practice
INSERT, SCREW THREAD, HELICAL COIL, METRIC SERIES, FREE RUNNING, CRES, UNCOATEDMA3279D (Current)01/09/2025
E-25 General Standards for Aerospace and Propulsion Systems
Technical Standard
LEDs and Aircraft ApplicationsARP6253A (Current)01/09/2025
This document presents minimum criteria for the design and installation of LED assemblies in aircraft. The use of "shall" in this specification expresses provisions that are binding. Nonmandatory provisions use the term "should
A-20C Interior Lighting
Recommended Practice
Air in Aircraft Hydraulic SystemsAIR5829 (Current)01/09/2025
This SAE Aerospace Information Report (AIR) discusses the forms that air may take in aircraft hydraulic systems. Further, the effects of the various air forms on system operation are addressed. Recommended system design to prevent air effects and maintenance procedures to prevent and remove air are provided. Nitrogen leakage from accumulators is also a source of gas in hydraulic systems and may compose a portion of the “air” in the hydraulic system. The term “air” in this report does not differentiate between a gas composed strictly of normal atmospheric air or one that includes a mixture of additional nitrogen as well. The discussions of the report apply equally with any proportions of atmospheric air and nitrogen in the system
A-6C1 Fluids and Contamination Control Committee
Information Report
Actuators, Linear Mechanical, General Specification GuideARP5812 (Current)01/09/2025
This SAE Aerospace Recommended Practice (ARP) establishes design, manufacturing performance and test requirements for linear mechanical actuators intended to be used for linear motion applications in response to manual or automatic power control system inputs. It is applicable, but not confined to, ball screws, sliding contact screws, roller screws, helical splines, rack and pinion assemblies, and skewed roller actuators. It is a reference for preparing detail specifications for mechanical actuators compatible and applicable to military or commercial aircraft systems
A-6B3 Electro-Mechanical Actuation Committee
Recommended Practice
Method for Predicting Lateral Attenuation of Airplane NoiseAIR5662 (Current)01/09/2025
This document describes analytical methods for calculating the attenuation of the level of the sound propagating from an airplane to locations on the ground and to the side of the flight path of an airplane during ground roll, climbout after liftoff, and landing operations. Both level and non-level ground scenarios may be modeled using these methods, however application is only directly applicable to terrain without significant undulations, which may cause multiple reflections and/or multiple shielding effects. This attenuation is termed lateral attenuation and is in excess of the attenuation from wave divergence and atmospheric absorption. The methods for calculating the lateral attenuation of the sound apply to: turbofan-powered transport-category airplanes with engines mounted at the rear of the fuselage (on the sides of the fuselage or in the center of the fuselage as well as on the sides) or under the wings propeller-driven transport-category or general-aviation airplanes
A-21 Aircraft Noise Measurement Aviation Emission Modeling
Information Report
Chloroprene (CR) Rubber Weather Resistant 65 - 75AMS3209M (Current)03/18/2014
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes
AMS CE Elastomers Committee
Material Specification
Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 1-1/8 Inches (28 mm), 0.23 to 2.00 Ounces per Yard (7.1 to 62.0 g/mAMS3793/5B (Current)09/11/2013
This specification covers three classes of para-aramid tape and webbing of a single width and with varying weights
AMS P Polymeric Materials Committee
Material Specification
Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 1-1/4 Inches (31 mm), 0.23 Ounces per Yard (7.1 g/mAMS3793/6B (Current)09/11/2013
This specification covers one class of para-aramid tape and webbing of a single width and with varying weights
AMS P Polymeric Materials Committee
Material Specification
Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 9/16 Inch (14 mm), 0.08 to 0.13 Ounces per Yard (2.5 to 4.0 g/mAMS3793/2B (Current)09/11/2013
This specification covers two classes of para-aramid tape and webbing of a single width and with varying weights
AMS P Polymeric Materials Committee
Material Specification
Steel Sheet and Strip, Corrosion and Moderate Heat Resistant 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Cold Rolled, TemperedAMS5546E (Current)04/05/2017
This specification covers a corrosion and moderate heat resistant steel in the form of sheet and strip
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Steel Castings, Tubular, Centrifugal, Corrosion Resistant 15Cr - 4.6Ni - 0.22 (Cb+Ta) - 2.8Cu Solution Heat TreatedAMS5348C (Current)04/04/2017
This specification covers a corrosion-resistant steel in the form of tubular centrifugal castings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 2.00 Inches (50 mm), 0.12 to 1.10 Ounces per Yard (3.7 to 34.1 g/mAMS3793/9B (Current)09/11/2013
This specifications covers thirteen classes of para-aramid tape and webbing of a single width and with varying weights
AMS P Polymeric Materials Committee
Material Specification
Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 1-3/4 Inches (44 mm), 0.17 to 2.50 Ounces per Yard (5.3 to 77.5 g/mAMS3793/8B (Current)09/11/2013
This specification covers eleven classes of para-aramid tape and webbing of a single width and with varying weights
AMS P Polymeric Materials Committee
Material Specification
Tape and Webbing, Textile, Para-Aramid Intermediate Modulus 1 Inch (25 mm), 0.08 to 1.65 Ounces per Yard (2.5 to 51.2 g/mAMS3793/4B (Current)09/11/2013
This specification covers twelve classes of para-aramid tape and webbing of a single width and with varying weights
AMS P Polymeric Materials Committee
Material Specification
Aluminum Alloy, Plate (2397-T87) 2.8Cu - 1.4Li - 0.30Mn - 0.12Zr - 0.10Zn Solution Heat Treated, Cold Worked, and Artificially AgedAMS4328B (Current)11/25/2019
This specification covers an aluminum alloy in the form of plate 3.000 to 6.000 inch (76.20 to 152.40 mm), inclusive, in nominal thickness (see 8.5
AMS D Nonferrous Alloys Committee
Material Specification
Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Cold Drawn, and AgedAMS5834E (Current)11/25/2019
This specification covers a corrosion and heat-resistant cobalt alloy in the form of round wire 0.001 to 0.140 inch (0.025 to 3.56 mm) inclusive in nominal diameter supplied in straight lengths or coils (see 8.6
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Steel Castings, Investment, Corrosion Resistant 18Cr - 9Ni Solution Heat TreatedAMS5358D (Current)04/04/2017
This specification covers a corrosion-resistant steel in the form of investment castings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Grease: Wide Temperature Range Lithium or Lithium Complex Thickened for Aircraft Wheel BearingsAMS3058A (Current)08/09/2018
This specification covers grease for use on aircraft wheel bearings. It also defines the quality control requirements to assure batch conformance and materials traceability, and the procedures to manage and communicate changes in the grease formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in 2.2, referencing this specification. Products qualified to this specification are listed on a Qualified Products List (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before a grease is approved for use in their equipment. Approval and/or certification for use of a specific grease in aero and aero-derived marine and industrial applications is the responsibility of the individual equipment builder and/or governmental authorities and is not implied by compliance with or qualification to this
AMS M Aerospace Greases Committee
Material Specification
Copper Sheet, Strip, and Plate Oxygen-Free, Light Cold RolledAMS4501F (Current)04/04/2017
This specification covers one type of copper in the form of sheet, strip, and plate
AMS D Nonferrous Alloys Committee
Material Specification
Corrosion-Resistant Steel Parts: Sampling, Inspection and Testing for Surface PassivationAMSSTD753B (Current)04/04/2017
This standard describes general and detailed methods of sampling and testing for surface passivity of corrosion-resistant steel parts. These tests may also be useful to determine if there is a need for passivation
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Aluminum Alloy Extrusions 8.6Fe - 1.8Se - 1.3V (8009-H112) Powder Metallurgy Product, Strain-HardenedAMS4309B (Current)04/04/2017
This specification covers an aluminum alloy powder metallurgy product in the form of round extrusions up to 3.5 inches (89 mm) in diameter and rectangular and other solid extrusions up to 10 square inches (64.5 cm2) in cross-sectional area. The maximum extrusion length is 100 inches (2.5 m
AMS D Nonferrous Alloys Committee
Material Specification
Rubber Silicone, High Strength, Cabin Pressure Seal Material, Diaphragm TypeAMSR83283A (Current)03/19/2014
This specification covers 45 durometer hardness, high strength silicone rubber
AMS CE Elastomers Committee
Material Specification
Tolerances, Metric Rubber ProductsMAM2279B (Current)03/19/2014
This specification covers established metric (SI) manufacturing tolerances applicable to non-cellular rubber products ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive" applies only to the higher figure of the specified range
AMS CE Elastomers Committee
Material Specification
Aluminum Alloy 2024, Bar, Rod, Shapes, Tube, and Wire, ExtrudedAMSQQA200/3A (Current)11/19/2019
This specification covers the specific requirements for aluminum alloy 2024 bar, rod, shapes, tube, and wire produced by extrusion
AMS D Nonferrous Alloys Committee
Material Specification
Magnesium Alloy, Sand Castings 2.8Nd - 1.4Gd - 0.4Zn - 0.6Zr (EV31A - T6) Solution and Precipitation Heat TreatedAMS4429B (Current)08/01/2019
This specification covers a magnesium alloy in the form of sand castings
AMS D Nonferrous Alloys Committee
Material Specification
Rubber, Fabricated ProductsAMSR3065A (Current)05/23/2011
This specification establishes the requirements for fabricated products of vulcanized rubber, synthetic rubber or rubberlike compositions alone or in combination, together with procedures for the inspection of such products (see 6.1
AMS CE Elastomers Committee
Material Specification
Magnesium Alloy Castings, Die 9.0Al - 0.70Zn (AZ91D, Temper F) As CastAMS4490K (Current)05/30/2017
This specification covers a magnesium alloy in the form of die castings
AMS D Nonferrous Alloys Committee
Material Specification
Compound, Corrosion Preventive Aircraft EngineAMS3072E (Current)04/05/2007
This specification covers a blend of corrosion-preventive compound concentrate and petroleum-base aircraft-engine lubricating oil in the form of a ready-to-use liquid
AMS B Finishes Processes and Fluids Committee
Material Specification
Aluminum Alloy, Sheet and Plate Copper Manganese Magnesium (17 S-TAMS4032C (Current)04/01/1946
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy Foil 1.0Mg - 0.6Si - 0.30Cu - 0.20Cr (6061-0) AnnealedAMS4009C (Current)05/30/2017
This specification covers an aluminum alloy in the form of foil
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy, Plate, Alclad 4.4cu 1.5mg 0.60mAMS4034C (Current)01/01/1968
SUPERSEDING SPECIFICATION: The requirements of this specification are embodied in the latest issue of AMS 4041, ALUMINUM ALLOY SHEET AND PLATE, ALCLAD (Alclad 2024 and 1-1/2% Alclad 2024-T3 Flat Sheet; 1-1/2% Alclad 2024-T351 Plate). The requirements of the latest issue of AMS 4041 shall be fulfilled whenever reference is made to this specification
AMS D Nonferrous Alloys Committee
Material Specification
Packaging, AerosolAMS2820B (Current)12/04/2000
This specification establishes requirements for aerosol packaging
AMS B Finishes Processes and Fluids Committee
Material Specification
Cleaning, Packaging, and Assembly of Critical Systems Components, Clean Area Procedure, 2500 Micron Max Particle SizeAMS2553A (Current)01/01/1992
This specification has been declared "CANCELLED" by the Aerospace Materials Division, SAE
AMS B Finishes Processes and Fluids Committee
Material Specification
Aluminum Alloy, Impact Extrusions 5.6zn 2.5mg 1.6cu 0.25cr (75s-T6AMS4170 (Current)01/01/1987
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy, Tubing, Hydraulic (6062 T6AMS4093A (Current)01/01/1966
SUPERSEDING SPECIFICATION: The requirements of this specification are embodied in the latest issue of AMS 4083, ALUMINUM ALLOY TUBING, HYDRAULIC, SEAMLESS, DRAWN (6061-T6). The requirements of the latest issue of AMS 4083 shall be fulfilled whenever reference is made to this specification
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy, Tubing Hydraulic (6062 T4AMS4091A (Current)01/01/1966
SUPERSEDING SPECIFICATION: The requirements of this specification are embodied in the latest of AMS 4081, ALUMINUM ALLOY TUBING, HYDRAULIC (6061-T4). The requirements of the latest issue of AMS 4081 shall be fulfilled whenever reference is made to this specification
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy, Tubing, Seamless, Drawn (6062 T6AMS4092A (Current)01/01/1966
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy Plate, Alclad - 5.6zn - 2.5mg - 1.6cu - 0.26cr (Alclad 7075-T651AMS4039C (Current)01/01/1968
SUPERSEDING SPECIFICATION: The requirements of this specification are embodied in the latest issue of AMS 4049, ALUMINUM ALLOY SHEET AND PLATE (Alclad 7075; -T6 Sheet, -T651 Plate). The requirements of the latest issue of AMS 4049 shall be fulfilled whenever reference is made to this specification
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy, Plate 4.4cu 1.5mg 0.60mnAMS4033C (Current)01/01/1968
SUPERSEDING SPECIFICATION: The requirements of this specification are embodied in the latest issue of AMS 4037, ALUMINUM ALLOY SHEET AND PLATE (2024; -T3 Flat Sheet, -T351 Plate). The requirements of the latest issue of AMS 4037 shall be fulfilled whenever reference is made to this specification
AMS D Nonferrous Alloys Committee
Material Specification
Aluminum Alloy, ExtrusionsAMS4155B (Current)01/01/1966
SUPERSEDING SPECIFICATION: The requirements of this specifications are embodied in the latest issue of AMS 4150, ALUMINUM ALLOY EXTRUSIONS (6061-T6). The requirements of the latest issue of AMS 4150 shall be fulfilled whenever reference is made to this specification
AMS D Nonferrous Alloys Committee
Material Specification
ALUMINUM ALLOY WELDING WIRE 7.0Si - 0.52Mg (357.0AMS4188/5 (Current)12/16/2002
This specification covers an aluminum alloy in the form of extruded or drawn welding wire
AMS D Nonferrous Alloys Committee
Material Specification
Selective (Brush) Nickel Plating Low-Stressed, Hard DepositAMS2439A (Current)10/01/2000
This specification covers the engineering requirements for selective (brush) electrodeposition of nickel and the properties of the deposit. This process has been used typically to provide good wear resistance and dimensional build-up and restoration of parts which may operate in service up to 450 degrees F (232 degrees C), where low tensile stress in the deposit is required, but usage is not limited to such applications. Diffusion heat treatment of the deposit is not required
AMS B Finishes Processes and Fluids Committee
Material Specification
Steel, Corrosion and Heat Resistant, Investment Castings 13Cr - 2.0Ni - 3.0W Hardened and Tempered to 32 - 38 HRCAMS5354G (Current)11/03/2023
This specification covers a corrosion and moderate heat resistant steel in the form of investment castings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Sealing Tape, Sheet, or Gasket, Polytetrafluoroethylene, Expanded (EPTFE) Oil and Water ResistantAMS3255B (Current)07/17/2017
This specification establishes the requirements for an expanded polytetrafluoroethylene (EPTFE) in the form of sealing tape, gaskets, or sheets requiring no mixing or curing
AMS G9 Aerospace Sealing Committee
Material Specification
Steel, Corrosion and Heat-Resistant, Investment Castings 19.5Cr - 10.5Ni - 0.65Cb (Nb) (CF-8C) Solution Heat TreatedAMS5364D (Current)11/03/2023
This specification covers a corrosion and heat-resistant steel in the form of investment castings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Continuous Identification Marking of Iron and Steel ProductsAMSSTD183A (Current)01/30/2003
This standard establishes uniform physical item identification marking in constantly recurring symbols for selected iron and steel products which are procured and issued for Government agencies. Shipment and inspection acceptance marking are not within the scope of this standard. The marking requirements of this standard are applicable when included in the item specification or individual contract. Government decision to include the marking requirements of this standard in a Government specification for iron and steel products shall be subject to coordination between the Government and the iron and steel industry
AMS E Carbon and Low Alloy Steels Committee
Material Specification
Items per page:
1 – 50 of 212033