Results
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems
This SAE Aerospace Standard (AS) defines the overall requirements applicable to oxygen flow indication as required by Airworthiness Requirements of CS/FAR 25.1449 to show that oxygen is being delivered to the dispensing equipment. Requirements of this document shall be applicable to any type of oxygen system technology and encompass “traditional” pneumatic devices, as well electric/electronic indication
This standard covers oxygen masks and breathing valves used with both panel mounted and mask mounted demand and pressure-demand oxygen regulators. Mask mounted oxygen regulators are covered under other standards, but when the mask mounted regulator incorporates an integral exhalation valve, the performance of this valve shall meet the requirements of this standard
This document provides guidance for oxygen cylinder installation on commerical aircraft based on airworthiness requirements, and methods practiced within aerospace industry. It covers considerations for oxygen systems from beginning of project phase up to production, maintenance, and servicing. The document is related to requirements of DOT-approved oxygen cylinders, as well to those designed and manufactured to standards of ISO 11119. However, its basic rules may also be applicable to new development pertaining to use of such equipment in an oxygen environment. For information regarding oxygen cylinders itself, also refer to AIR825/12
This SAE Standard covers low voltage primary cable intended for use at a nominal system voltage of 60 VDC (25 VAC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse
This document covers cable, shielded and jacketed, intended for use at a nominal system voltage up to 1000 V (AC rms or DC). It is intended for use in surface vehicle electrical systems
This standard covers ultra-thin wall low voltage primary cable intended for use at a nominal system voltage of 60 VDC (60 VAC rms) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse. This standard covers SAE conductor sizes which usually differ from ISO conductor sizes
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the development of aircraft and systems, taking into account aircraft functions and operating environment. It provides practices for ensuring the safety of the overall aircraft design, showing compliance with regulations, and assisting a company in developing and meeting its own internal standards. These practices include validation of requirements and verification of the design implementation for safety, certification, and product assurance. The guidelines in this document were developed in the context of U.S. Title 14 Code of Federal Regulations (14 CFR) Part 25 and European Union Aviation Safety Agency (EASA) Certification Specification (CS) CS-25. They may be applicable in the context of other regulations, such as 14 CFR Parts 23, 27, 29, 33, and 35, and CS-23, CS-27, CS-29, CS-E, and CS-P. This document addresses the development cycle for aircraft and systems that implement aircraft and system functions. It
This Standard specifies the test methods, dimensions, and requirements for single-core 60 V cables intended for use in road vehicle applications where the nominal system voltage ≤ 60 V DC (25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is > 60 V DC (25 V AC) to ≤ 600 V DC (600 V AC). Where practical, this standard uses ISO 6722 for test methods, dimensions, and requirements. This standard covers ISO conductor sizes which usually differ from SAE conductor sizes. It also covers the individual cores in multi-core cables. See ISO 6722 for “Temperature Class Ratings
This SAE Standard covers un-shielded balanced single twisted pair data cable intended for use in surface vehicle cables for ≤100 Mb/s Ethernet applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
No scope available
No scope available
This drawing specifies parts AS54712, AS54713, AS54714, AS54715, AS54716, AS54717, AS54718, AS54719, AS54720, AS54721, AS54722, AS54723, AS54724, AS54725, AS54726, AS54727, AS54728, AS54729, AS54730, AS54731, AS54732, AS54734, AS54736, AS54738, AS54740, AS54742, AS54744, AS54746, AS54748, AS54750, AS54752, AS54754, AS54756, AS54758, AS54760, AS54762, AS54764, AS54766, AS54768, AS54770, AS54772, AS54774, AS54776, AS54778, AS54780, AS54782, AS54784, AS54786, AS54788, AS54790, AS54792, AS54794, and AS54796. To view suppliers qualified to manufacture this part, visit https://ts200.sae-itc.org
This drawing specifies parts AS55018, AS55019, AS55020, AS55021, AS55022, AS55023, AS55024, AS55025, AS55026, AS55027, AS55028, AS55029, AS55030, AS55031, AS55032, AS55034, AS55036, AS55038, AS55040, AS55042, AS55044, AS55046, AS55048, AS55050, AS55052, AS55054, AS55056, AS55058, AS55060, AS55062, AS55064, AS55066, AS55068, AS55070, AS55072, AS55074, AS55076, AS55078, AS55080, AS55082, AS55084, AS55086, AS55088, AS55090, AS55092, AS55094, and AS55096. To view suppliers qualified to manufacture this part, visit https://ts200.sae-itc.org
See Table 1
See Table 1
This specification covers a copper alloy (naval brass) in the form of bars and rods (see 8.5
This specification establishes the requirements for etch inspection of steel parts to detect overheating (rehardening or over-tempering) caused by abusive machining or grinding or to detect localized discontinuous carburization
This SAE Standard covers unshielded cable, 22 gauge and larger, intended for use at a nominal system voltage up to 600 V or 1000 V (ACrms or DC). It is intended for use in surface vehicle electrical systems
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.00 inch (25.4 mm) and under in nominal thickness
This specification covers one type of copper in the form of wire (see 8.5
This standard covers a single shielded balanced pair (twisted or parallel) jacketed data cable intended for use in surface vehicle cables for 2.5, 5, and 10 Gb/s Ethernet applications. The tests in this standard are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission
This document specifies the on-board system requirements for vehicle-to-vehicle (V2V) safety system for school buses, including functional requirements and performance requirements. The system can send the SAE J2735-defined basic safety message (BSM) over a wireless communications interface; the communications interface itself is outside the scope of this document. This document provides the specifications necessary to build interoperable systems that support V2V applications that rely on receiving BSMs from school buses
This SAE Recommended Practice presents a method and example results for determining the Automotive Safety Integrity Level (ASIL) for automotive motion control electrical and/or electronic (E/E) systems. The ASIL determination activity is required by ISO 26262-3, and it is intended that the process and results herein are consistent with ISO 26262. The technical focus of this document is on vehicle motion control systems. The scope of this SAE Recommended Practice is limited to collision-related hazards associated with motion control systems. This SAE Recommended Practice focuses on motion control systems since the hazards they can create generally have higher ASIL ratings, as compared to the hazards non-motion control systems can create. Because of this, the Functional Safety Committee decided to give motion control systems a higher priority and focus exclusively on them in this SAE Recommended Practice. ISO 26262 has a wider scope than SAE J2980, covering other functions and accidents
This terminology is intended to provide a common nomenclature for use in publishing road vehicle aerodynamics data and reports
This Recommended Practice provides a procedure for measuring and documenting the aerodynamic performance in a full-scale wind tunnel of passenger vehicles, i.e., mass-produced cars and light-duty trucks intended primarily for individual consumers. Testing or numerical modeling of pre-production and/or reduced-scale models is outside the scope of this document. Aerodynamic development procedures, i.e., methods to improve or optimize aerodynamic performance, are also excluded. It is well-known that aerodynamic performance results depend significantly on vehicle content and loading, as well as the wind tunnel itself (type, scale, and simulation qualities of the wind tunnel). Publication of non-standard test results causes unnecessary additional development work and incorrect perception of a vehicle’s anticipated aerodynamic performance by government, academia, and the general public. The intent of this document is to promote uniformity and traceability of published aerodynamic performance
This SAE Aerospace Recommended Practice (ARP) details the recommended process for correcting measured non-volatile particulate matter (nvPM) mass and number data for particle losses in the sampling and measurement system specified in ARP6320B. This technique is only recommended for conditions where both nvPM mass and number concentration measurements are in the valid measurement ranges of the instruments that are discussed in the tool limitations section. This ARP also supplies an Excel software tool with documentation to automate the process. The body of this ARP details the recommended calculation method, uncertainties, and limitations of the system loss correction factors. It explains, in detail, the required inputs and outputs from the supplied Excel software tool (developed on Windows 7, Excel 2016). Also included are: The Excel correction tools (refer to Attachments I and V). Installation instructions for a Windows-based computer (refer to Attachment II). A user technical manual
This document provides the specifications of horizontal hard-bearing balancing machines, which make such machines suitable for gas turbine rotor balancing
This SAE Information Report has been prepared at the request of the SAE Road Vehicle Aerodynamics Forum Committee (RVAC), incorporating material from earlier revisions of the document first prepared by the Standards Committee on Cooling Flow Measurement (CFM). Although a great deal is already known about engine cooling, recent concern with fuel conservation has resulted in generally smaller air intakes whose shape and location are dictated primarily by low vehicle drag/high forward speed requirements. The new vehicle intake configurations make it more difficult to achieve adequate cooling under all conditions. They cause cooling flow velocity profiles to become distorted and underhood temperatures to be excessively high. Such problems make it necessary to achieve much better accuracy in measuring cooling flows. As the following descriptions show, each company or institution concerned with this problem has invested a lot of time and as a result gained considerable experience in
This specification covers the requirements for black oxide coatings on parts
This specification covers design requirements, performance requirements, and methods of procurement for tools and associated accessories used to strip aerospace vehicle electrical wire and cable. Aerospace vehicle electrical wire has stranded conductors with protective plating and specialized insulation. Poor quality wire strippers or mismatched blades can compromise the performance of wiring
This specification covers an aluminum alloy in the form of clad sheet from 0.006 to 0.249 inches (0.15 to 6.32 mm), inclusive, in thickness (see 8.6
This SAE Aerospace Standard (AS) provides design criteria and performance tests for portable, handheld, battery-powered, electronic megaphones used by aircraft crew members to provide information and guidance in the event of an aircraft emergency or other non-routine situation
This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods
This specification covers a corrosion-resistant steel product in the solution and precipitation heat treated (H1000) condition, 12 inches (305 mm) and under in nominal diameter, thickness, or, for hexagons, least distance between parallel sides
Items per page:
50
1 – 50 of 209383