Search
Advanced Search
of the following are true
(
)

Results

Items (211,878)
This SAE Recommended Practice covers passive torque biasing axle and center differentials used in passenger car and light truck applications. Differentials are of the bevel gear, helical gear, and planetary types, although other configurations are possible.
Drivetrain Standards Committee
This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET. This document is intended to provide design direction for the single phase nominal 120 VAC as it interfaces within the truck 12 VDC battery and electrical architecture providing power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off.
Truck and Bus Electrical Systems Committee
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
A-6C2 Seals Committee
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
AE-8C1 Connectors Committee
This specification establishes the procedure for installing hardened key types studs and inserts, eliminating the need for broaching key slots. It also defines the hole preparation necessary to install the studs and inserts.
E-25 General Standards for Aerospace and Propulsion Systems
This standard describes the accepted methods used for preparing aerospace sealant test specimens for qualification and quality conformance or acceptance testing. AS5127/1 and AS5127/2 are to be used in conjunction with this document and the applicable AMS specifications.
AMS G9 Aerospace Sealing Committee
The objective of this report is to serve as an introductory (educational) document to cover the potential failure mechanisms related to EIS in high voltage electrical component or HV electrical equipment in aircraft power systems. It has the following contents: (1) an overview of the current understandings of potential failure mechanisms related to EIS for high voltage and high-power application in aircraft; (2) main aging stressors and aging processes of EIS in electrical components used in the aircraft power systems and their common failure modes, and (3) the key indicators to assess the status of electrical insulation degradation and related testing needs. This document aims to assist HV power system designers in understanding the key considerations for EIS design and testing of HV components in aircraft, as well as the requirements for predicting their designed service life. Detailed testing guideline including testing methods will be provided in ARP7375, and life modeling in
AE-11 Aging Models for Electrical Insulation in Hi-Enrgy Sys
This specification and its supplementary detail specifications cover a woven nylon cloth coated with polyether (EU) urethane.
AMS P Polymeric Materials Committee
This specification and its supplementary detail specifications cover a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet.
AMS P Polymeric Materials Committee
This paper was prepared to support supersession of MIL-S-8879C with Screw Thread Conformity Task Force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. The STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.
E-25 General Standards for Aerospace and Propulsion Systems
This specification covers a magnesium alloy in the form of welding wire (see 8.5).
AMS D Nonferrous Alloys Committee
This specification covers a titanium alloy in the form of sheet, strip, and plate up to 4.000 inches (101.60 mm), inclusive.
AMS G Titanium and Refractory Metals Committee
Items per page:
1 – 50 of 211878