Results
This specification covers bonded honeycomb core made of aluminum alloy and supplied in the form of blocks, slices, or other configurations as ordered (see 8.5
This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine-driven cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depends on the volumetric flow rate, or the pressure rise across the fan, since these two
This specification covers an aircraft-quality, corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.000 inch (25.40 mm) and under in nominal thickness
This specification covers a low-carbon steel in the form of wire up to 0.249 inch (6.32 mm), inclusive, supplied as coils of wire or, when specified, as straight lengths
The supplier shall use the following process to respond to a customer request for corrective and preventive action
This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance
This specification covers the requirements for an electrodeposit of cadmium diffused into an electrodeposit of nickel on carbon, low-alloy, and corrosion-resistant steels
This specification covers the requirements for electrodeposition of tin on metals and the properties of the deposit
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock
This set of criteria is intended for use by accredited Certification Bodies (CBs) to establish compliance and grant certification to AS6081A. It may also be used by others to assess compliance to AS6081A requirements
The purpose of this SAE Recommended Practice is to establish reference standards for airflow measurements in the ranges required for testing automotive engine induction systems and to describe equipment that will facilitate the use of such standards to check the accuracy of various equipment and methods
Define a process enabling network devices to detect the baud rate of a CAN Classic network as specified by physical layers SAE J1939-11, SAE J1939-14, or SAE J1939-15. The intent is to minimize or eliminate communication disruption between existing network devices. These networks only support Classical Base Frame Format (CBFF) and Classical Extended Frame Format (CEFF) Data Frames, as defined in ISO 11898-1:2015. Baud rate detection on a SAE J1939 CAN FD network is not in scope, as SAE J1939-17 is currently the only SAE J1939 CAN FD physical layer option and specifies only one supported baud rate combination (500 kbit/s / 2000 kbit/s
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, O-ring cord, compression seals, and molded-in-place gaskets for aeronautical and aerospace applications
This document establishes age limit and guidance for acceptance of hose and hose assemblies containing elastomeric materials for use in aircraft, space vehicles, missiles and component assemblies thereof at time of delivery to the contractor, procuring activity, or contracting officer. This document does not establish limitations on storage times for military/civil activities nor operating life
This SAE Aerospace Recommended Practice establishes the requirements and procedures for eddy current inspection of open fastener holes in aluminum aircraft structures
This specification covers a precision cold-rolled corrosion- and heat-resistant nickel alloy in the form of sheet and strip over 0.005 to 0.015 inch (0.13 to 0.38 mm), inclusive, in nominal thickness and foil up to 0.005 inch (0.13 mm), inclusive, in nominal thickness (see 8.4
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems
This SAE Standard covers un-shielded balanced single twisted pair data cable intended for use in surface vehicle cables for ≤100 Mb/s Ethernet applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission
This document specifies the on-board system requirements for vehicle-to-vehicle (V2V) safety system for school buses, including functional requirements and performance requirements. The system can send the SAE J2735-defined basic safety message (BSM) over a wireless communications interface; the communications interface itself is outside the scope of this document. This document provides the specifications necessary to build interoperable systems that support V2V applications that rely on receiving BSMs from school buses
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness
This SAE Aerospace Standard (AS) defines the overall requirements applicable to oxygen flow indication as required by Airworthiness Requirements of CS/FAR 25.1449 to show that oxygen is being delivered to the dispensing equipment. Requirements of this document shall be applicable to any type of oxygen system technology and encompass “traditional” pneumatic devices, as well electric/electronic indication
This document provides guidance for oxygen cylinder installation on commerical aircraft based on airworthiness requirements, and methods practiced within aerospace industry. It covers considerations for oxygen systems from beginning of project phase up to production, maintenance, and servicing. The document is related to requirements of DOT-approved oxygen cylinders, as well to those designed and manufactured to standards of ISO 11119. However, its basic rules may also be applicable to new development pertaining to use of such equipment in an oxygen environment. For information regarding oxygen cylinders itself, also refer to AIR825/12
This specification covers the specific requirements for 2017 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing supplied in the annealed (O temper) condition (see 8.4). When specified, product shall be supplied in the “as fabricated” (F) temper
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
This SAE Recommended Practice establishes uniform procedures for assuring the manufactured quality, installed utility, and service performance of manual automotive adaptive products, other than those provided by the OEM, intended to provide driving capability for persons with physical disabilities. These devices function as adaptive appliances to compensate for lost or reduced performance in the drivers’ arms or legs, or both. Some of the devices are designed to transfer foot functions to the hands, hand functions to the feet, or functions from one side of the body to the other. This document applies only to primary controls as defined in 3.4.1 and in the Foreword. In particular, this document is specifically concerned with those mechanical and hybrid products that are intended by the manufacturer of the adaptive product to: Be installed within the occupant space of the vehicle Be operated by a vehicle driver with a physical disability Be added to, or substituted for, the OEM vehicle
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.00 inch (25.4 mm) and under in nominal thickness
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate
This specification covers one type of copper in the form of wire (see 8.5
This SAE Standard covers low voltage primary cable intended for use at a nominal system voltage of 60 VDC (25 VAC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse
Items per page:
50
1 – 50 of 209603