Search
Advanced Search
of the following are true
(
)

Results

Items (210,745)
This SAE Recommended Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10 000 lb) or less: a Minimum performance standards for the windshield washer system. b Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities. c Uniform terminology of windshield washer system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d Guides for the design and location of components of the systems for function, servicing of the system, etc. The minimum performance requirements and test procedures, outlined in this document, are based on currently available engineering data. It is intended that all portions of the document will be periodically reviewed and revised as additional data on windshield washer system performance are developed
Wiper Standards Committee
This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods for specifying thickness tolerances
Metals Technical Committee
This SAE Recommended Practice establishes limits for electrical circuits on motor vehicle safety glazing materials
Glazing Materials Standards Committee
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by EPA, and M1 category vehicles as defined by the European Commission
Interior Climate Control Vehicle OEM Committee
This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine-driven cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depends on the volumetric flow rate, or the pressure rise across the fan, since these two
Cooling Systems Standards Committee
This SAE Recommended Practice is intended for stakeholders of the automotive industry that are conducting emission testing on materials, parts, or components used in automotive interiors. Testing methods may specifically define the handling and packaging conditions for the material to be analyzed. In these cases, follow the method as closely as possible. Use this document as a guide where the protocol for handling and packaging the samples between production and testing may be undefined or ambiguous
Volatile Organic Compounds
This SAE recommended practice defines and establishes tolerances and attributes of cold rolled strip steels. Differences between cold rolled strip and cold rolled sheet products are discussed so that process designers can make informed material selection decisions
Metals Technical Committee
Zinc and zinc-alloy coated steel is used to enhance a structure’s protection against corrosion degradation. For the purpose of this SAE Recommended Practice, a galvanized coating is defined as a zinc or zinc-alloy metallic coating. The selection of the optimum galvanized steel sheet product depends on many factors, the most important being: desired corrosion protection, formability, weldability, surface characteristics, and paintability. The trade-offs of these product characteristics are more complex than is the case with uncoated steel sheet products
Metals Technical Committee
This SAE Recommended Practice is intended for use in testing and evaluating the performance of electric cooling fan (ECF) assemblies typically used for vehicle engine cooling. Conducted in a laboratory environment with intended heat exchangers, the performance measurement includes fan output in terms of airflow and pressure and fan motor input in terms of voltage and current. This information can be used to calculate the efficiency of the assembly, including aerodynamic efficiency of the fan and shroud, and electrical efficiency of the motor. The electric power consumption can be used to estimate electrical charging system sizing and fuel economy. The performance of a given fan assembly depends on the installation details of the application, including the effects of system resistance and geometries of the grill, heat exchangers, engine and other underhood components, and front end components. This document provides guidance for duplicating such details in the test setup for accurate
Cooling Systems Standards Committee
This SAE Recommended Practice is applicable to Electric Drive Cooling Fan Assemblies used in Light Duty vehicle cooling systems (typically, passenger cars and light duty trucks). This document outlines the Electric Drive Cooling Fan Motor Mounting interface characteristics such that a common standard is possible
Cooling Systems Standards Committee
This SAE Recommended Practice establishes mechanical property ranges for low-carbon automotive hot-rolled sheet, cold-rolled sheet, and metallic-coated sheet steels. It also contains information that explains the different nomenclature used with these steels
Metals Technical Committee
This specification covers an aluminum alloy in the form of plate 4.001 to 10.000 inches (101.60 to 254.00 mm), inclusive, in nominal thickness
AMS D Nonferrous Alloys Committee
This Recommended Practice applies to engine cooling fans up to 2000 mm in diameter with a mounting interface consisting of a pilot hole and a circular bolt pattern. Most of these fans are belt, gear, clutch, hydraulically, or electrically driven
Cooling Systems Standards Committee
This SAE Recommended Practice is applicable to all heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine the heat transfer and pressure drop performance under specified conditions. This document has been reviewed and revised by adding several clarifying statements to Section 4
Cooling Systems Standards Committee
This specification provides processing and acceptance requirements for electrical discharge machining (EDM) when applied to the manufacturing of parts
AMS B Finishes Processes and Fluids Committee
This standard covers design requirements, performance requirements, and methods of procurement for tools and associated accessories used to cut aerospace vehicle electrical wire and cable. Aerospace vehicle electrical wire has stranded conductors with protective plating and specialized insulation. Poor quality wire cutting can compromise the performance of wiring
AE-8C2 Terminating Devices and Tooling Committee
This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life. The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents. However, when the requirements of this document are in conflict with the customer's requirements or specifications, the requirements of the customer's detailed specification
A-6C2 Seals Committee
This SAE Systems Management Standard specifies the Habitability processes throughout planning, design, development, test, production, use and disposal of a system. Depending on contract phase and/or complexity of the program, tailoring of this standard may be applied. Appendix C provides guidance on tailoring standard requirements to fit the various DoD acquisition pathways. The primary goals of a contractor Habitability program include: Ensuring that the system design complies with the customer Habitability requirements and that discrepancies are reported to management and the customer. Identifying, coordinating, tracking, prioritizing, and resolving Habitability risks and issues and ensuring that they are: ◦ Reflected in the contractor proposal, budgets, and plans. ◦ Raised at design, management, and program reviews. ◦ Debated in working group meetings. ◦ Coordinated with Training, logistics, and the other HSI disciplines. ◦ Included appropriately in documentation and deliverable
G-45 Human Systems Integration
This SAE Aerospace Information Report (AIR) provides information and guidelines on the selection and use of rotary lip seals for their expected duty cycle. Information on seal installation procedures is also included. NOTE: This document does not address mechanical or magnetic face seals
A-6C2 Seals Committee
This SAE Aerospace Standard (AS) specifies scarf-cut polytetrafluoroethylene (PTFE) retainers (backup rings) for use in glands in accordance with AS4716. They are usually used in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with O-rings and other seals for static and dynamic applications. NOTE: This specification includes material tests but does not include hydraulic or pneumatic performance tests
A-6C2 Seals Committee
This SAE Aerospace Standard (AS) specifies the dimensions, tolerances and size codes (dash numbers) for O-rings with a larger cross-section than those to AS568, for use in glands per MIL-G-5514 where squeeze at low temperature is often insufficient to provide a leak-tight seal
A-6C2 Seals Committee
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for back-up rings machined from AMS3678/1 polytetrafluoroethylene materials for use in AS5202 ports. It shall be used for procurement purposes
A-6C2 Seals Committee
This SAE Aerospace Standard (AS) defines gland details for scrapers for rod diameters from 1/4 to 15-1/2 inch (6.35 to 393.70 mm) inclusive, corresponding to AS568 O-ring Dash No. sizes -108/-111, -206/-222, -325/-349, and -425/-460. The gland details herein allow the use of more stable, efficient, and reliable scraper devices than MS33675 glands
A-6C2 Seals Committee
An attempt has been made to consider all features of seal ring design including configuration, materials, hardness, dimensions, surface finishes, surface treatment, leak testing, and general quality. In addition to this, allowable cylinder breathing and general quality requirements of mating hardware are discussed. Also, at the end of this report, there is a brief paragraph on other types of seal rings
A-6C2 Seals Committee
This specification and part standard specifies polytetrafluoroethylene (PTFE) resin material and the dimensional requirements for scarf-cut retainers (backup rings) previously specified by MIL-R-8791 and MIL-R-8791/1. The retainers are intended for use in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with seals and O-rings
A-6C2 Seals Committee
This specification controls surface condition, manufacturing defects and inspection requirements, and defines methods of measurement for elastomeric toroidal sealing rings (O-rings) for static (including gasket) applications
A-6C2 Seals Committee
This SAE Recommended Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less: a Minimum performance standards for windshield wiper systems. b Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities. c Uniform terminology of windshield wiper system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d Guides for the design and location of components of the systems for function, servicing of the system, etc. The test procedures and minimum performance standards outlined in this document are based on currently available engineering data. It is the intent that all portions of the document will be periodically reviewed and revised as additional data regarding windshield wiping system performance are developed
Wiper Standards Committee
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings machined from AMS3617 polyamide material. It shall be used for procurement purposes
A-6C2 Seals Committee
This SAE Aerospace Recommended Practice (ARP) provides guidelines for the application of polymeric bearings for linear actuation systems. Design considerations are included for recommended fit and function in conjunction with material selection and load-bearing capability
A-6C2 Seals Committee
Items per page:
1 – 50 of 210745