Results
This SAE Recommended Practice provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability, and environmental performance when tested according to SAE J2902
This specification covers a premium aircraft-quality, alloy steel in the form of bars, forgings, and forging stock
This procurement specification covers aircraft-quality bolts and screws made of 6Al - 4V titanium alloy of the type identified under the Unified Numbering System as UNS R56400. The following specification designation and its properties are covered
The scope of this SAE Recommended Practice is limited to gasoline fuel pumps used in automotive direct fuel injection systems. It is primarily restricted to bench tests. This SAE Recommended Practice also defines the minimum design verification testing that is recommended to verify the suitability of gasoline direct injection (GDI) high-pressure fuel pumps used for pumping gasoline or gasoline-blend fuels to direct injection gasoline injectors. Additional tests not specified in SAE J2714 will be required for non-automotive pump applications or pumps, such as those intended for use on aircraft, motorcycles, or marine equipment. The pump and the gasoline direct injector are complementary components, and the direct injector component is fully described in SAE J2713, which provides a full range of test procedures for the characterization of such injectors. Except where specifically stated otherwise, test results are recorded for individual parts under recommended test conditions. Where
The purpose of this SAE Standard is to define a common set of thermodynamic test conditions to evaluate internal heat exchangers for use with R-134a and R-1234yf refrigerants in mobile air-conditioning systems. This SAE Standard can be used to test actual vehicle IHX designs or standardized IHX samples, which can be used for comparison based on a common length and shape
This SAE Recommended Practice promotes uniformity in the evaluation tests and performance measurements that are conducted on fuel injectors used in low-pressure gasoline engine applications. The scope of this document is limited to electronically actuated fuel injection devices that are utilized in automotive gasoline port fuel injection systems where the fuel supply pressure is normally less than 1000 kPa. Detailed test procedures are provided for determining numerous PFI injector parameters, including, but not limited to, flow curves, leakage, electromechanical performance, fluid compatibility and corrosion susceptibility, durability, the effects of vibration and torsional deflection, thermal cycling effects, and noise. The standardized measurement procedures in this document are all bench tests. Characterization of the fuel spray from a low-pressure gasoline port fuel injector is quite important; however, these spray characterization tests are not addressed in this document, but are
This SAE Recommended Practice covers the wiring and rectangularly shaped connector standards for all types of trailers whose gross weight does not exceed 4540 kg (10 000 lb). These trailers are grouped in SAE J684 with running light circuit loads not to exceed 7.5 A per circuit. This document provides circuits for lighting, electric brakes, trailer battery charging, and an auxiliary circuit color code and protection for the wiring from hazards or short circuits. Color code is compatible with SAE J560 and ISO 1724-1980(E
This SAE Recommended Practice provides procedures for determining shot peening coverage and relating coverage to part exposure to the media stream. Effectiveness of shot peening is directly dependent on coverage. Inadequate or excessive coverage can be detrimental to fatigue strength and component life
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder
This specification covers established inch/pound manufacturing tolerances applicable to bars and rods of copper and copper alloys ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of a specified range
This SAE Aerospace Standard specifies the dimensional, design criteria, fabrication, performance, operational, environmental, and testing requirements for interline pallets requiring airworthiness approval for loading onto civil transport aircraft equipped with NAS3610/AS36100 restraint systems and using pallet nets meeting the requirements of AS1492. Type II/2 covers NAS3610/AS36100 code sizes. Type III pallets have been removed from this SAE Aerospace Standard revision
This procedure covers vehicle operation and electric dynamometer (dyno) load coefficient adjustment to simulate track road load within dynamometer inertia and road load simulation capabilities
This specification covers a corrosion- and heat-resistant steel in the form of welding wire
This procedure applies to directional control valves or other valves which in various positions direct or block fluid flow as applied to Off-Road Self-Propelled Work Machines as referenced in SAE J1116
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, and components. Said actuators are used for applying cam type foundation brakes by slack adjuster means
This specification covers all aspects in Electrical Wiring Interconnection Systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles, and external pods
SAE J1362 presents graphical symbols for use on operator controls and other displays on off-road work machines as defined in SAE J1116, plus mobile cranes, but excluding agricultural tractors. Symbols for agricultural tractors are covered by ASABE S304, ISO 3767-1, and ISO 3767-2
This SAE Recommended Practice identifies and defines requirements relating to the safe integration of the fuel cell system, the hydrogen fuel storage and handling systems (as defined and specified in SAE J2579) and high voltage electrical systems into the overall Fuel Cell Vehicle. The document may also be applied to hydrogen vehicles with internal combustion engines. This document relates to the overall design, construction, operation and maintenance of fuel cell vehicles
This document is an information report and intended to provide an overview of the Clock Extension Peripheral Interface (CXPI) protocol
The intent of this SAE Aerospace Information Report (AIR) is to summarize and review the E34 committee’s efforts to educate the aerospace propulsion lubrication community on the science of micropitting, its consequences, and the various tribology evaluation methods that can be employed under aviation related conditions to differentiate formulation related aggravating factors
This SAE Aerospace Information Report (AIR) includes general design information on materials, procurement specifications, and mechanical properties for bolts and screws developed for use on aerospace propulsion systems. Both inch and metric (SI) designs are included
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing
This specification covers a titanium alloy in the form of bars and rods 1.00 inch (25.4 mm) and under in nominal diameter
This specification covers a premium aircraft-quality, low-alloy steel in the form of sheet, strip, and plate
Items per page:
50
1 – 50 of 212827