Results
With many corporations and suppliers conducting development and validation tests at different climatic wind tunnel sites, there is an increasing need for a recommended best practice that defines a process by which climatic wind tunnels can be correlated. This document addresses the test methods and metrics used to correlate results from different facilities, independent of location, for heating ventilation and air conditioning (HVAC) and powertrain cooling (PTC) development. This document should be used as a guideline to make sure key aspects of tunnel testing are covered when comparing various climatic wind tunnel facilities. The depth of the correlation program is ultimately influenced by program objectives; therefore, a correlation program, for the intent and purposes of this document, can range from just a few tests to a full analysis that involves multiple vehicle tests identifying limitations and statistical boundaries. Using recommendations in this document will eliminate most
This specification covers an aluminum alloy in the form of two types of welding wire
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-rings with a coded part number
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and flash welded rings up through 4.000 in2 (25.81 cm2) cross-section and stock for flash welded rings
SAE J1978/ISO 15031-4 specifies a complementary set of functions to be provided by an OBD-II scan tool. These functions provide complete, efficient, and safe access to all regulated OBD (on-board diagnostic) services on any vehicle which is compliant with SAE J1978/ISO 15031-4. The SAE J1978 content of this document is intended to satisfy the requirements of an OBD-II scan tool as required by current U.S. on-board diagnostic (OBD) regulations. The ISO 15031-4 content of this document is intended to satisfy the requirements of OBD requirements in countries other than the U.S., and includes functionality not required or not allowed in the U.S. This document specifies: A means of establishing communications between an OBD-equipped vehicle and an OBD-II scan tool. A set of diagnostic services to be provided by an OBD-II scan tool in order to exercise the services defined in SAE J1979/ISO 15031-5. SAE J1978/ISO 15031-4 does not preclude the inclusion of additional capabilities or functions
SAE J1502 specifies dimensions, performance requirements, and test procedures for the male half of a diagnostic coupler with either a metric M14x1.5 or an inch 9/16-18 straight thread stud end. The coupler is designed for use with a mineral-based hydraulic fluid. It is used on machines specified in SAE J1116. It does not apply to the mating hydraulic quick action couplings not on the machine. Diagnostic couplings in accordance with SAE J1502 may be used at a working pressure of 42 MPa. The permissible working pressure depends upon the materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of SAE J1502 does not guarantee rated performance. Each manufacturer should perform testing according to the specification contained in this document to ensure that components comply with the performance rating
This standard defines requirements for the preparation and execution of the audit process. In addition, it defines the content and composition for the audit reporting of conformity and process effectiveness to the 9100-series standards, the organization's QMS documentation, and customer and statutory/regulatory requirements. The requirements in this standard are additions or represent changes to the requirements and guidelines in the standards for conformity assessment, auditing, and certification as published by ISO/IEC (i.e., ISO/IEC 17000, ISO/IEC 17021-1). When there is conflict with these standards, the requirements of the 9101 standard shall take precedence
This specification covers fuel-resistant, two-component polysulfide synthetic rubber compounds which cure at room temperature
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings
This specification covers a low-alloy steel in the form of wire supplied as coils, spools, and straight lengths
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings
This specification covers a titanium alloy in the form of round, hexagon and square bars and forgings up through 3.000 inches (76.20 mm), inclusive, rectangular bar and forgings of thickness up through 4.000 inches (101.60 mm), inclusive, and forging stock of any size (see 8.6
The intent of this SAE Aerospace Information Report (AIR) is to summarize and review the E34 committee’s efforts to educate the aerospace propulsion lubrication community on the science of micropitting, its consequences, and the various tribology evaluation methods that can be employed under aviation related conditions to differentiate formulation related aggravating factors
This specification covers a titanium alloy in the form of sheet and strip up to and including 0.125 inch (3.18 mm) in nominal thickness
This SAE Aerospace Standard (AS) defines contamination classes and levels for particulate contamination of hydraulic fluids and includes methods of reporting related data (Appendix A
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This specification covers polyurethane (PUR) in the form of two-component sealing compounds
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal earthboring machines as defined by SAE J2022
Items per page:
50
1 – 50 of 212620