Results
This SAE Standard provides test procedures, requirements, and guidelines for motorcycle turn signal lamps. It does not apply to mopeds
This test method provides a standardized procedure for evaluating the electrochemical resistance of automotive coolant hose and materials. Electrochemical degradation has been determined to be a major cause of EPDM coolant system hose failures. The test method consists of a procedure which induces voltage to a test specimen while it is exposed to a water/coolant solution. Method #1, referred to as a “Brabolyzer” test, is a whole hose test. Method #2, referred to as a “U” tube test, uses cured plate samples or plates prepared from tube material removed from hose (Method No. 2 is intended as a screening test only). Any test parameters other than those specified in this SAE Recommended Practice, are to be agreed to by the tester and the requester
This test code describes tests for determining characteristics of hydraulic positive displacement motors as used on off-road self-propelled work machines as referenced in SAE J1116
This SAE Standard applies to horizontal earthboring machines found in SAE J2022 of the following types: a Auger boring machines b Rod pushers c Rotary rod machines d Impact machines This document does not apply to horizontal directional drilling (HDD) machines as defined in ISO 21467, mining machinery covered in SAE J1116, Table 1, nor does it apply to conveyors, tunnel boring machines, pipe jacking systems, micro tunnelers, or well drilling machines
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness
This specification covers polyvinyl chloride insulated single conductor electric wires made with tin-coated copper conductors or silver-coated copper alloy conductors. The polyvinyl chloride insulation of these wires may be used alone or in combination with other insulating or protective materials
This specification defines the requirements for a grooved clamp coupling and flanges suitable for joining intermediate pressure and temperature ducting in aircraft air systems. The rigid coupling joint assembly, hereafter referred to as "the joint", shall operate within the temperature range of -65 °F to +800 °F
This specification covers a titanium alloy in the form of round bar and wire 0.625 inch (15.88 mm) and under in nominal diameter or thickness (see 8.7
This specification covers a premium aircraft-quality corrosion-resistant steel in the form of bars, forgings, and forging stock
This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm) in nominal diameter or least distance between parallel sides, inclusive, and maximum cross-sectional area of 32 square inches (206.5 cm2), forgings of thickness up through 4.000 inches (101.60 mm), inclusive, and maximum cross-sectional area of 32 square inches (206.5 cm2), and stock for forging of any size (see 8.6
This SAE Aerospace Information Report (AIR) has been written for individuals associated with ground level testing of turbofan and turbojet engines and particularly for those who might be interested in investigating the performance characteristics of a new test cell design or of proposed modifications to an existing test cell by means of a scale model test
This specification covers an aluminum alloy in the form of plate 0.250 to 5.500 inch (6.35 to 139.70 mm), inclusive, in nominal thickness (see 8.5
This specification covers aluminum and aluminum alloy foil in the form of laminated sheet (see 8.6
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4 inches (101.6 mm) (see 8.5
This specification covers a silicone (MQ/VMQ/PVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be designated for use in molded O-rings and molded O-ring cord, molded rings, compression seals, molded-in-place gaskets, and plate seals for aeronautical and aerospace applications
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, mechanical tubing, forgings, and forging stock
This specification covers a discontinuously reinforced aluminum alloy (DRA) made by mechanical alloying 2124A aluminum powder and silicon carbide particulate (SiC). It is produced in the form of extruded bar, rod, wire, and shapes with cross section inclusive of 1-inch (25.4-mm) diameter or less (see 8.7
This specification covers an age-hardenable nitriding grade of aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light trucks having gross vehicle weight rating (GVWR) of 4540 kg (10 000 lb) or less. The test procedure is characterized by having fixed initial conditions (specified initial vehicle speed and gear selection at the starting point on the test site) to obtain vehicle interior sound measurement during road load operation over various road surfaces at specified constant speeds. The measurement data so derived is useful for vehicle engineering development and analysis
This SAE Recommended Practice is intended for use in testing and evaluating the performance of electric cooling fan (ECF) assemblies typically used for vehicle engine cooling. Conducted in a laboratory environment with intended heat exchangers, the performance measurement includes fan output in terms of airflow and pressure and fan motor input in terms of voltage and current. This information can be used to calculate the efficiency of the assembly, including aerodynamic efficiency of the fan and shroud, and electrical efficiency of the motor. The electric power consumption can be used to estimate electrical charging system sizing and fuel economy. The performance of a given fan assembly depends on the installation details of the application, including the effects of system resistance and geometries of the grill, heat exchangers, engine and other underhood components, and front end components. This document provides guidance for duplicating such details in the test setup for accurate
This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These are often called “mini coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the mini coax connection system described here is 50 Ω, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable
This specification covers a titanium alloy in the form of bars up through 1.000 inch (25.40 mm) in diameter or least distance between parallel sides, inclusive, forgings of thickness up through 1.000 inch (25.40 mm), inclusive, high-strength fastener stock up through 1.250 inch (31.75 mm), inclusive, and stock for forging of any size (see 8.7
This specification covers a discontinuously reinforced aluminum alloy (DRA) made by mechanical alloying 2124A aluminum powder and silicon carbide (SiC) particulate. It is produced in the form of extruded bar, rod, wire, and shapes with cross section inclusive of 1-inch (25.4-mm) diameter or less (see 8.7
This SAE Recommended Practice applies to motor vehicle Forward Illumination Devices which incorporate limited adaptive beam pattern capabilities. This document is to be used in conjunction with other forward lighting standards and/or recommended practices which define the base beam procedures, requirements, and guidelines
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings
This specification covers virgin, unfilled polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in dimension parallel to the direction of applied molding pressure, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm
This specification covers the requirements for electrodeposited bronze plate and its subsequent removal
This specification covers two types of virgin, unfilled polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in length, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm
This SAE Aerospace Recommended Practice (ARP) provides an overview of the various types of polytetrafluoroethylene (PTFE) backup rings for hydraulic and pneumatic fluid power applications, including their advantages and disadvantages
This standard establishes basic design criteria including preferred bend radii, straight lengths between bends, flattening and surface conditions in the bend area. Also included is a table of preferred tubing sizes and wall thicknesses and a formula for determining a minimum bend radius for a given tube diameter
The environment and test waveforms defined in this SAE Aerospace Recommended Practice (ARP) account for the best lightning data and analysis currently available. The quantified environment and levels herein represent the minimum currently required by certifying authorities, which is consistent with the approach applied in related lightning documents. Lightning, like other weather phenomenon, is probabilistic in nature. Levels and waveforms vary considerably from one flash to the next. Within this document, standardized voltage and current waveforms have been derived to represent the lightning environment external to an aircraft. These standardized waveforms are used to assess the effects of lightning on aircraft. The standardized external current waveforms have, in turn, been used to derive standardized transient voltage and current test waveforms that can be expected to appear on cable bundles and at equipment interfaces within an aircraft. When deriving these latter internal induced
Items per page:
50
1 – 50 of 212826