Search
Advanced Search
of the following are true

Results

Items (208,189)
ARINC 858 Part 2 provides aviation ground system gateway considerations necessary to transition to the Internet Protocol Suite (IPS). ARINC 858 Part 2 describes the principles of operation for an IPS gateway that enables ACARS application messages to be exchanged between an IPS aircraft and a ground ACARS host. ARINC 858 Part 2 also describes the principles of operation for an IPS gateway that enables OSI-based application messages to be exchanged between an IPS host and an OSI end system. This product was developed in coordination with ICAO WG-I, RTCA SC-223, and EUROCAE WG-108
Airlines Electronic Engineering Committee
This ARP describes recommended sampling conditions, instrumentation, and procedures for the measurement of nonvolatile particle number and mass concentrations from the exhaust of aircraft gas turbine engines. Procedures are included to estimate sampling system loss performance. This ARP is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode. This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances
E-31P Particulate Matter Committee
This User Guide describes the content of the Enterprise Architect (EA) version of the UCS Architectural Model and how to use this model within the EA modeling tool environment. The purpose of the EA version of the UCS Architectural Interface Control Document (ICD) model is to provide a working model for Enterprise Architect tool users and to serve as the source model for the Rational Software Architect (RSA) and Rhapsody models (AIR6516 and AIR6517). The AIR6515 EA Model has been validated to contain the same content as the AS6518 model for: all UCS ICD interfaces all UCS ICD messages all UCS ICD data directly or indirectly referenced by ICD messages and interfaces the Domain Participant, Information, Service, and Non-Functional Properties Models
AS-4UCS Unmanned Systems Control Segment Architecture
This specification has been "CANCELLED" by the Aerospace Materials Division, SAE, as of October 1995
AMS P Polymeric Materials Committee
The process detailed within this document is generic and applies to the entire end-to-end health management capability, covering both on-board and on-ground elements, in both commercial and military applications throughout their lifecycle. This ARP addresses a gap in guidance related to usage of ground-based health management equipment for airworthiness credit, ensuring a level of integrity commensurate with the potential aircraft-level consequences of the relevant failure conditions. The practical application of this standardized process is detailed in the form of a checklist. The on-board elements described here are typically the source of the data acquisition used for off-board analysis. The on-board aspects relating to airworthiness and/or safety of flight, e.g., pilot notification, are addressed by existing guidance and policy documents. If a proposed health management capability for airworthiness credit involves modification of the on-board systems, the substantiation of those
E-32 Aerospace Propulsion Systems Health Management
Various emergency situations may require the dispensing of oxygen to all occupants of aircraft during flight. During an emergency event, depending on the aircraft operational flight capability, all cabin occupants must be serviced by a mask presentation system connected to an operational oxygen source. Several regulations specify the functional characteristics and requirements of the oxygen systems for aircraft in support of different missions. These should be referred to for the exact functional performance requirements. It is not the intent of this document to ensure conformance with these regulations, but only to recommend general concepts for the location of the oxygen masks and oxygen system outlets for proper accessibility by the aircraft occupants, whether cabin occupants or crew members. Different requirements may apply when the mission of the pressurized aircraft or the operational altitude of the aircraft is not in excess of FL250. When the aircraft is operating above FL100
A-10 Aircraft Oxygen Equipment Committee
This SAE Aerospace Standard (AS) covers the requirements and technical guidance for evaluation of life-cycle cost, productivity, and safety/health factors related to power hand tool selection. It applies approaches to selection of quieter and lower vibration handheld powered tools, with optimal ergonomic features, for the prevention of hand-arm vibration syndrome (HAVS), hearing loss, and repetitive motion injuries. Equipment selection for control of physical safety and electrical safety hazards are essential components of a tool safety program. It suggests use of noise and vibration data provided by vendors to be verified and supplemented by information available through the National Institute for Occupational Safety and Health (NIOSH) and European Union (EU) databases. This AS has been updated to better address physical safety hazards. An appendix (APPENDIX D) on dust control has been included. A supporting SAE Aerospace Information Report (AIR6916) has been developed to facilitate
EG-1B1 Power Tools - Productivity, Ergonomics and Safety
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) b Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) Different thread forms on each end are permissible. c Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches) UNRC threads (1/4 through 4 inches) UNRC threads (1/4 through 4 inches) UNRF
Ship Systems - Fasteners Committee
This SAE Part Standard covers selected machine screw nuts manufactured in accordance with American Society for Mechanical Engineers (ASME) dimensional standards. This document covers material most often used in ship systems and equipment but its use may be applied wherever nuts of the covered materials are used. This document permits the nuts to be identified and ordered by a part identification number (PIN) as defined in this document
Ship Systems - Fasteners Committee
This SAE Recommended Practice covers a procedure for evaluating plastic and multiple-layer coatings exposed to gravelometer testing (as defined in SAE J400) with an optical imaging and analysis system. The intent of the procedure is to detect, count and characterize instances of damage in the coated surface that fracture the top coat layer or penetrate through multiple layers of the coating system. It may be possible to extend this methodology of coating damage evaluation to specimens that have undergone test procedures or exposures that produce similar, discrete damage sites in the coating system. If so applied, evaluation results must be interpreted with respect to the limitations and intent implied by the original evaluation procedure and its associated rating system, if applicable
Textile and Flexible Plastics Committee
This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control
Connector Systems Standards Committee
This specification covers a general-purpose disinfectant in the form of a concentrated liquid
AMS J Aircraft Maintenance Chemicals and Materials Committee
This specification covers a corrosion-resistant steel in the form of bars, forgings, and forging stock
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers the engineering requirements for producing brazed joints in parts fabricated from steels, iron alloys, nickel alloys, cobalt alloys, and copper alloys by use of silver alloys, and the properties of such joints
AMS B Finishes Processes and Fluids Committee
SAE GEIA-STD-0007C defines logistics product data generated during the requirement definition and design of an industry or government system, end item, or product. It makes use of the Extensible Markup Language (XML) through the use of entities and attributes that comprise logistics product data and their definitions. The standard is designed to provide users with a uniform set of data tags for all or portions of logistics product data. The standard can be applied to any industry or government product, system or equipment acquisition program, major modification program, and applicable research and development projects. This standard is for use by both industry and government activities. As used in this standard, the requiring authority is generally the customer and the customer can be a government or industry activity. The performing activity may be either a industry or government activity. The use of the term “contract” in this standard includes any document of agreement between
LCLS Life Cycle Logistics Supportability
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403
Truck Bus Control and Communications Network Committee
This SAE Recommended Practice is intended to provide basic recommended practices for aid in the development and use of safe and efficient practices for all operations involving the production, handling, and dispensing of SAE J1703 motor vehicle brake fluids and SAE J1704 borate ester-based brake fluids
Brake Fluids Standards Committee
This specification defines test methods and performance criteria for ultrasonically welded wire-to-terminal bonds as shown in Figure 1. This specification subjects parts to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures referenced in this specification include thermal shock, temperature humidity cycling, and mechanical stress. This specification is intended to evaluate the strength and performance of the interface between wires and the electrical terminal pad. The graphics used are specific to the linear weld type of process equipment. Validation of the terminal is a separate task (refer to a component validation test such as SAE/USCAR-2). If the weld under test (WUT) is different than described in this section or is subjected to conditions beyond what is typical of automotive use, the test sequence may not be applicable. Ensure that parts used in other conditions are validated for the actual conditions encountered. Vehicle and product
USCAR
This document covers un-shielded balanced single twisted pair data cable intended for use in surface vehicle cables for 100 Mbps Ethernet applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission
Cable Standards Committee
This specification covers one grade of commercially pure titanium in the form of sheet, strip, and plate 1.000 inch (25.40 mm) and under in nominal thickness (see 8.5
AMS G Titanium and Refractory Metals Committee
This specification covers a corrosion-resistant steel in the form of investment castings
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers an aluminum alloy in the form of flat sheet and plate 0.020 to 0.500 inch (0.51 to 12.70 mm) and under in nominal thickness (see 8.5
AMS D Nonferrous Alloys Committee
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This interface control document (ICD) specifies all software services in the Unmanned Systems (UxS) Control Segment Architecture, including interfaces, messages, and data model
AS-4UCS Unmanned Systems Control Segment Architecture
This SAE Recommended Practice establishes a standard method to perform screening test sequences that identify a brake friction material’s effectiveness under various test conditions. The result is an evaluation of brake friction material effectiveness under a set of defined braking conditions considered most relevant to automobile braking system development
Brake Dynamometer Standards Committee
This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensure that the particle retention ability of the filter is measured in a single pass, as no appreciable loading or regression will occur
Filter Test Methods Standards Committee
This SAE Standard covers general and dimensional specifications for the Code 62 metric (Type 1) and inch (Type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS and FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flange clamps are not for new design. The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail
Hydraulic Hose and Hose Fittings Committee
This specification covers a corrosion and heat resistant steel in the form of welded tubing
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers one width and strength of nylon tape
AMS P Polymeric Materials Committee
This SAE Aerospace Standard (AS) standardizes inspection and test procedures, workmanship criteria, and minimum training and certification requirements to detect Suspect/Counterfeit (SC) Electrical, Electronic, and Electromechanical (EEE) parts. The requirements of this document apply once a decision is made to use parts with unknown chain of custody that do not have pedigree back to the original component manufacturer or have been acquired from a broker or independent distributor, or when there are other known risk elements that result in the User/Requester to have concerns about potential SC EEE parts. The tests specified by this standard may also detect occurrences of malicious tampering, although the current version of this standard is not designed specifically for this purpose. This standard ensures consistency across the supply chain for test techniques and requirements based on assessed risk associated with the application, component, supplier, and other relevant risk factors
G-19A Test Laboratory Standards Development Committee
This SAE Aerospace Standard (AS) specifies solid, un-cut polytetrafluoroethylene (PTFE) retainers (backup rings) for use in glands in accordance with AS4716. They are usually used in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with O-rings and other seals for static and dynamic applications
A-6C2 Seals Committee
This standard provides the guideline for enhancements to adaptive cruise control (ACC) by the addition of wireless communication from relevant vehicles (V2V) and/or the infrastructure (I2V) to augment the ACC active sensing capability. The CACC system operates under driver responsibility and supervision and is limited to the following: Does only longitudinal control of the vehicle. Uses time gap control strategy similar to ACC. Motor vehicles covered in the scope of this document include light and heavy vehicles. The message elements to realize CACC and platooning are part of the scope. The initial release covers definitions for CACC and platooning and requirements for CACC, while a subsequent release will cover the platooning requirements
V2X Vehicular Applications Technical Committee
This recommended practice establishes test procedures and best practices for PM measurements under partial flow conditions. PFDS PM testing and certification is primarily used in heavy duty applications as described in 40 CFR Part 1065 because full flow sampling systems with a dilution tunnel and CVS can be very bulky for large heavy duty engines. 40 CFR Part 1066 also allows the use of partial flow systems for light duty applications in lieu of full flow systems. PFDS does not require the use of a CVS sampling system or a full flow dilution tunnel. This makes it easier and more convenient to perform PM measurement in smaller test cells that cannot fit a large CVS or a full flow dilution tunnel. This document describes the different components/specifications of LD and HD PFDS as well as the required quality checks necessary to ensure the integrity of the sampling system. It also addresses the many sampling options and calculations that are approved by the regulations. Correlation
Emissions Standards Committee
This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor
Truck and Bus Low Speed Communication Network Committee
This design standard provides information on the use of self-locking shank nuts, thread sizes .1640-36 through .3750-24, together with details of flange hole and abutment shoulder for their installation
E-25 General Standards for Aerospace and Propulsion Systems
This SAE Aerospace Recommended Practice (ARP) recommends the maintainability features that should be considered in the design of aircraft wheels and brakes. The effect on other factors, such as cost, weight, reliability, and compatibility with other systems, should be weighed before incorporation of any of these maintainability features into the design
A-5A Wheels, Brakes and Skid Controls Committee
Enhanced License for Data Dictionary for Quantities Used in Cyber Physical Systems (AS6969B) allowing for greater usage as outlined in the terms of the Enhanced License. Terms can be reviewed prior to purchase once item is added to the cart. Data Dictionary for Quantities Used in Cyber Physical Systems (AS6969B) This data dictionary provides definitions for quantities commonly used in the command and control of cyber physical systems. It defines mathematical and logical terms, quantities, measurement units, reference systems, measurands, and measurements. It also defines common quantity modalities. The dictionary is structured to be convenient to data modelers. It is also extendable so that users can create their own quantity domains
AS-4UCS Unmanned Systems Control Segment Architecture
The purpose of this document is to give the reader an overview of the document package which makes up AIR825, Introduction to Oxygen Equipment for Aircraft, and a basic overview (see Section 4) of the operational concerns driven by human physiology during altitude exposure
A-10 Aircraft Oxygen Equipment Committee
This SAE Part Standard covers selected inch screws, bolts, structural bolts, and nuts manufactured in accordance with ASTM International and SAE fastener standards. Appendix A covers bolt blanks to manufacture fitted bolts of specific materials. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document
Ship Systems - Fasteners Committee
This SAE Parts Standard provides dimensional and quality assurance requirements for M6 through M36 metric sizes of studs in the following configurations in materials needed for ship system applications: a Continuous thread studs in M thread profile. b Double end studs—clamping type (also called bolt-studs) where both ends are of the same thread series but different lengths (M thread profile
Ship Systems - Fasteners Committee
This SAE Part Standard covers selected inch dimensioned set screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document
Ship Systems - Fasteners Committee
SAE J2886 Design Review Based on Failure Modes (DRBFM) Recommended Practice is intended for Automotive and Non-Automotive applications. It describes the basic principles and processes of DRBFM including planning, preparation, change point FMEA, design reviews, decisions based on actions completed, and feedback loops to other processes, such as design, validation and process guidelines (Appendix B - DRBFM Process Map). The intent of each fundamental step of the DRBFM methodology is presented. It is intended for use by organizations whose product development processes currently (or intend to) use Failure Mode & Effects Analysis (FMEA) or DRBFM as a tool for assessing the potential risk and reliability of system elements (product or process) or as part of their product improvement processes. DRBFM is not intended to replace FMEA however, companies interested in adopting DRBFM will benefit from the focus on specific change points and supporting engineering decisions based on detailed
Automotive Quality and Process Improvement Committee
This SAE Standard applies to refrigerant identification equipment used for identifying an acceptable level of R-1234yf purity in a refrigerant tank or vehicle MAC system labeled as containing R-1234yf, and not misidentify other refrigerants, per 5.7
Interior Climate Control Service Committee
This standard covers ultra-thin wall low voltage primary cable intended for use at a nominal system voltage of 60 VDC (60 VAC rms) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse. This standard covers SAE conductor sizes which usually differ from ISO conductor sizes
Cable Standards Committee
Items per page:
1 – 50 of 208189