Results
Primarily to provide recommendations concerning minimizing stress-corrosion cracking in wrought titanium alloy products.
This specification covers an aluminum alloy in the form of plate 1.000 to 6.000 inches (25.40 to 152.40 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy procured in the form of extruded profiles (shapes) with nominal thickness of over 0.040 to 0.375 inch (over 1.00 to 9.5 mm), inclusive, and cross sections up to 7.75 square inches (5000 mm2) and circle sizes as indicated (see 8.5).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing produced with cross-sectional area of 32 square inches (206 cm2), maximum (see 8.6).
This specification covers the requirements for the application and properties of a titanium nitride coating on metal parts applied by physical vapor deposition (PVD).
This specification covers an aluminum alloy in the form of hand forgings 11.000 inches (280 mm) and under in nominal thickness and of forging stock of any size (see 8.6).
This specification covers an aluminum alloy in the form of die and hand forgings 4 inches (102 mm) and under in thickness, rolled or forged rings 2.50 inches (63.5 mm) and under in radial thickness, and stock of any size for forging or rings (see 8.5).
This document is intended to describe how to conduct lightning direct effects tests and indirect system upset effects tests. Indirect effects upset and damage tolerance tests for individual equipment items are addressed in RTCA DO-160/ED-14. Documents relating to other aspects of the certification process, including definition of the lightning environment, zoning, and indirect effects certification, are listed in Section 2. This document presents test techniques for simulated lightning testing of aircraft and the associated systems. This document does not include design criteria, nor does it specify which items should or should not be tested. Acceptable levels of damage and/or pass/fail criteria for the qualification tests must be approved by the appropriate airworthiness authority for each particular case. When lightning tests are a part of a certification plan, the test methods described herein are an acceptable means, but not the only means, of meeting the test requirements of the
This SAE Standard covers the mini-shed testing methodology to measure the rate of refrigerant loss from an automotive air conditioning (A/C) system. This SAE procedure encompasses both front and rear air conditioning systems utilizing refrigerants operating under sub-critical conditions. The SAE procedure will cover multiple refrigerants to emission testing and is utilized for evaluating air condtioning systems. Heat pump systems can also be evaluated; however, they will have different usage and mission profiles.
This SAE Recommended Practice establishes the method to determine Sound Level of a snowmobile under typical trail operating conditions. Snowmobiles have different engine power levels that depends on the model.
This SAE Standard describes guarding to help prevent hazardous machine movement caused by activation of the starter motor by bypassing the starter control system. This document is applicable to off-road, self-propelled work machines, as identified in SAE J1116, and agricultural tractors, as defined in ANSI/ASAE S390, which have the potential for hazardous machine movement as a result of bypassing the starter control system and powering of the starter motor.
This SAE Standard provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.
This Recommended Practice provides procedures for defining the Accelerator Heel Point and the Accommodation Tool Reference Point, a point on the seat H-point travel path which is used for locating various driver workspace accommodation tools in Class B vehicles (heavy trucks and buses). Three accommodation tool reference points are available depending on the percentages of males and females in the expected driver population (50:50, 75:25, and 90:10 to 95:5). These procedures are applicable to both the SAE J826 HPM and the SAE J4002 HPM-II.
This SAE Aerospace Standard (AS) provides a performance station designation system for aircraft propulsion systems and their derivatives.
This SAE Recommended Practice covers transfer cases used in passenger car and light truck applications. Transfer cases are of the chain, geared, manually and electronically shifted types although other configurations are possible. The operating points (speeds, temperatures, etc.) were chosen to mirror those of the United States Environmental Protection Agency Vehicle Chassis Dynamometer Driving Schedules (DDS).
This SAE Standard applies to dyes intended to be introduced into a mobile air-conditioning system refrigerant circuit for the purpose of allowing the application of ultraviolet leak detection. In order to label any product(s), they shall meet SAE J2297, the certification process as described in SAE J2911 must be followed, and the documentation described in Appendix A shall be submitted to SAE.
This specification covers performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in road vehicle applications that are: low voltage (0 to 60 VDC) or coaxial. Incomplete (mechanical) specifications for jacketed twisted pair connectors are also provided. These procedures are only applicable to terminals used for in-line, header, and device connector systems. They are not applicable to edge board connector systems, twist-lock connector systems, >60 VAC or DC, or to eyelet terminals. No electrical connector, terminal, or related component may be represented as having met USCAR specifications unless conformance to all applicable requirements of this specification have been verified and documented. All required verification and documentation must be done by the supplier of the part or parts. If testing is performed by another source, it does not relieve the primary
This SAE standard specifies a method for testing and measuring a normalized elastic constant of brake pad assemblies using ultrasound. This document applies to disc brake pad assemblies and its coupons or segments used in road vehicles.
This SAE Recommended Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less: a Minimum performance standards for windshield wiper systems. b Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities. c Uniform terminology of windshield wiper system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance. d Guides for the design and location of components of the systems for function, servicing of the system, etc. The test procedures and minimum performance standards outlined in this document are based on currently available engineering data. It is the intent that all portions of the document will be periodically reviewed and revised as additional data regarding windshield wiping system performance are developed.
This SAE Standard for reliability-centered maintenance (RCM) is intended for use by any organization that has or makes use of physical assets or systems that it wishes to manage responsibly.
This specification covers one type of copper in the form of wire (see 8.5).
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.00 inch (25.4 mm) and under in nominal thickness.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness.
The definitions and illustrations in this SAE Recommended Practice are intended to establish common nomenclature and terminology for automotive transmission one-way clutches.
This specification covers a titanium alloy in the form of sheet.
This SAE Recommended Practice establishes uniform procedures for assuring the manufactured quality, installed utility, and service performance of manual automotive adaptive products, other than those provided by the OEM, intended to provide driving capability for persons with physical disabilities. These devices function as adaptive appliances to compensate for lost or reduced performance in the drivers’ arms or legs, or both. Some of the devices are designed to transfer foot functions to the hands, hand functions to the feet, or functions from one side of the body to the other. This document applies only to primary controls as defined in 3.4.1 and in the Foreword. In particular, this document is specifically concerned with those mechanical and hybrid products that are intended by the manufacturer of the adaptive product to: Be installed within the occupant space of the vehicle Be operated by a vehicle driver with a physical disability Be added to, or substituted for, the OEM vehicle
This recommended practice describes general characteristics of VIN systems. It includes certain specific requirements, supporting definitions, basic content, and examples.
Items per page:
50
1 – 50 of 212183