Search
Advanced Search
of the following are true

Results

Items (207,327)
This SAE Aerospace Recommended Practice (ARP) provides recommendations for: The audit process in general A list of specific areas of attention to be audited Maintaining the test facility in such a manner that it meets audit requirements
EG-1E Gas Turbine Test Facilities and Equipment
This document provides background information, rationale, and data (both physical testing and computer simulations) used in defining the component test methods and similarity criteria described in SAE Aerospace Recommended Practice (ARP) 6330. ARP6330 defines multiple test methods used to assess the effect of seat back mounted IFE monitor changes on blunt trauma to the head and post-impact sharp edge generation. The data generated is based on seat and IFE components installed on type A-T (transport airplane) certified aircraft. While not within the scope of ARP6330, generated test data for the possible future development of surrogate target evaluation methods is also included
Aircraft Seat Committee
The procedures contained in this specification cover the laboratory testing of Exterior Lamps for use in automotive road illumination. The following tests are intended to be run under the following conditions. This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards. If other manufacture’s components are intended to be approved for use in the lamp assembly, then those possible combinations of components shall be considered a new lamp assembly and shall also be tested
USCAR
The purpose of this SAE Recommended Practice is to establish guidelines for the automatic transmission and hydraulic systems engineer to design cast iron sealing rings and select acceptable width, thickness, coatings, and other accepted design details
Automatic Transmission and Transaxle Committee
This SAE Standard measures the percent thermal efficiency of materials in sleeve form used to contain heat or insulate around a hot component. The percent thermal efficiency (%TE) is determined by measuring the power difference expended by the heat source (cartridge heater) with and without the test sleeve at the specified temperature. See SAE J2302 to measure radiant heat flow of sleeves
Harness Covering Standards Committee
This SAE Standard covers the general and dimensional data for industrial quality spherical rod ends commonly used on control linkages in metric automotive, marine, construction, and industrial equipment applications. The rod ends described are available from several manufacturers within the range of the interchangeable specifications. The sliding contact spherical self-aligning bearing members (ball and socket) are available in a variety of materials in the types shown. The load capacities and wear capabilities vary considerably with the design and fabrication. It is suggested that the manufacturers be consulted for recommendations for the type and design appropriate to particular applications
Materials, Processes and Parts Council
With many corporations and suppliers conducting development and validation tests at different climatic wind tunnel sites, there is an increasing need for a recommended best practice that defines a process by which climatic wind tunnels can be correlated. This document addresses the test methods and metrics used to correlate results from different facilities, independent of location, for heating ventilation and air conditioning (HVAC) and powertrain cooling (PTC) development. This document should be used as a guideline to make sure key aspects of tunnel testing are covered when comparing various climatic wind tunnel facilities. The depth of the correlation program is ultimately influenced by program objectives; therefore, a correlation program, for the intent and purposes of this document, can range from just a few tests to a full analysis that involves multiple vehicle tests identifying limitations and statistical boundaries. Using recommendations in this document will eliminate most
Interior Climate Control Vehicle OEM Committee
The SAE Recommended Practice specifies the test procedure to assure valve assemblies which are satisfactory for vehicle usage, and it is applicable to new valve assemblies for commercial production. It covers such valves where they are employed in passenger car and light truck brake systems utilizing motor vehicle hydraulic brake fluids. This procedure and requirements (SAE J1137) was developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3); however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These procedure specifications were developed for base brake operation and do not consider the effects of ABS (anti-lock brake systems) or traction control systems which may have a significant effect on the valve. Careful analysis of the particular type ABS and/or traction control (if included in the system) should be made and additional tests are required which are not included in this document. Provisions for ABS and traction control will be incorporated
Hydraulic Brake Components Standards Committee
This SAE Standard provides test procedures, requirements, and guidelines for motorcycle turn signal lamps. It does not apply to mopeds
Motorcycle Lighting Standards Committee
This document provides the technical requirements for implementing the SAE J1939 Functional Safety Communication Protocol in a manner determined suitable for meeting industry applicable functional safety standards
Truck Bus Control and Communications Network Committee
Differences, where they exist, are shown in Appendix A with associated rationale. This SAE Standard defines the most commonly used terms for piston rings. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. The terms and definitions apply to piston rings for reciprocating internal combustion engines and compressors working under analogous conditions. Appendix B is included which lists equivalent terms in English, French, Russian, German, Spanish, Portuguese, Italian, and Japanese
Piston and Ring Standards Committee
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations
Surface Enhancement Committee
These general operator precautions apply to horizontal earthboring machines as defined in SAE J2022. These should not be considered as all-inclusive for all specific uses and unique features of each particular type of machine. Other more specific operator precautions not mentioned herein should be covered by users of this SAE Recommended Practice for each particular machine application. Purpose This document is intended to be used as a guide for manufacturers and users of horizontal earthboring machines to improve the degree of personal safety for operators and others during normal operation and servicing. Avoidance of accidents also depends upon the care exercised by such persons. Inclusion of this practice in state, federal, or any laws or regulations where flexibility of revision is lacking is discouraged
MTC9, Trenching and Horizontal Earthboring Machines
This SAE Standard establishes the minimum construction and performance requirements for seven conductor 1/8-2/10-4/12 cable for use on trucks, trailers, and converter dollies for 12 VDC nominal applications. Where appropriate, the standard refers to two types of cables (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction
Truck and Bus Electrical Systems Committee
This SAE Standard establishes uniform test procedures for the defrosting systems of off-road, self-propelled work machines used in construction, general purpose industrial, agricultural, and forestry machinery as referenced in table one of this document. It includes tests that can be conducted with uniform test equipment in commercially available laboratory facilities, as well as in an appropriate outdoor environment
HFTC6, Operator Accommodation
This SAE Standard provides a uniform method for determining rated and struck capacity for buckets used on excavators, mini-excavators, and backhoes as defined in SAE J1057 and equipped with hoe attachment. Calculations are based on the inside physical dimensions of the bucket only, without use of optional side cutters, spill guards, teeth, or other accessories and without regard to bucket action provided by any specific machine. This document does not cover shovel, clam, or dragline buckets described in SAE J67 or loaders buckets described in SAE J742
MTC1, Earthmoving Machinery
Specifications, test methods, and usage provisions for safety glazing materials used for glazing of motor vehicles and motor vehicle equipment operating on land highways
Glazing Materials Standards Committee
This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE band friction test machine is used to evaluate the frictional characteristics of automatic transmission band friction materials with automatic transmission fluids. It can also be used to conduct durability tests on wet friction systems
Automatic Transmission and Transaxle Committee
This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull. It also provides the means for documenting and checking the declared (rated) power published by the manufacturer
Marine Technical Steering Committee
This SAE Standard applies to electronic probe-type leak detectors used to service motor vehicle passenger compartment air-conditioning systems. This document does not address any safety issues concerning their design or use
Interior Climate Control Service Committee
This SAE Recommended Practice establishes the recommended locations for the air brake and electrical connections for the back of a truck-tractor and the front of a truck-trailer
Truck and Bus Brake Supply and Control Components Committee
This information report presents the terminology and definitions as used in the fiberboard industry
Textile and Flexible Plastics Committee
The subject matter contained within this SAE Information Report is set forth by the Class A Task Force of the Vehicle Network for Multiplexing and Data Communications (Multiplex) Committee as information the network system designer should consider. The Task Force realizes that the information contained in this report may be somewhat controversial and a consensus throughout the industry does not exist at this time. The Task Force also intends that the analysis set forth in this document is for sharing information and encouraging debate on the benefits of utilizing a multiple network architecture
Vehicle Architecture For Data Communications Standards
This SAE Recommended Practice describes the test procedures for conducting quasi-static frontal strength test for COE heavy truck applications. Its purpose is to establish recommended test procedures which will standardize the procedure for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included
Truck Crashworthiness Committee
This SAE Recommended Practice is intended for the determination of the losses of hydrocarbon fluids, by permeation through component walls, as well as through "microleaks" at interfaces of assembled components while controlling temperature and pressure independently of each other. This is achieved in a recirculating system in which elements of a test fuel that permeate through the walls of a test specimen and migrate through the interfaces are transported by a controlled flow of dry nitrogen to a point where they are measured. That measurement point is a device, such as a canister containing activated charcoal or other means of collection or accumulation where the hydrocarbon losses are then measured by weight change or analyzed by some other suitable means
Fuel Systems Standards Committee
This SAE Recommended Practice establishes uniform test procedures and performance requirements for engine coolant type heating systems of enclosed truck cabs. The intent is to provide a test that will ensure acceptable comfort for cab occupants. It is limited to a test that can be conducted on uniform test equipment in commercially available laboratory facilities. There are two options for producing hot coolant in this document. Testing using these two approaches on the same vehicle will not necessarily provide identical results. Many vehicle models are offered with optional engines, and each engine has varying coolant temperatures and flow rates. If the test is being conducted to compare the performance of one heater design to another heater design, then the external coolant source approach (Test A) will yield the most comparable results. If the test is being conducted to validate the heater installation on a specific vehicle model with a specific engine, then using the engine to heat
Truck and Bus Windshield Wipers and Climate Control Comm
Data from this SAE Recommended Practice permit mapping axle efficiency and/or waste energy over the operating range of trucks, busses, and other highway vehicles based on truck chasses
Truck and Bus Powertrain Committee
This SAE Recommended Practice outlines a series of performance recommendations which concern the whole data channel. These recommendations are not subject to any variation and all of them should be adhered to by any agency conducting tests to this practice. However, the method of demonstrating compliance with the recommendations is flexible and can be adapted to suit the needs of the particular equipment the agency is using. It is not intended that each recommendation be taken in a literal sense, as necessitating a single test to demonstrate that the recommendation is met. Rather, it is intended that any agency proposing to conduct tests to this document should be able to demonstrate that if such a single test could be and were carried out, then their equipment would meet the recommendations. This demonstration should be undertaken on the basis of reasonable deductions from evidence in their possession, such as the results of partial tests. In some systems it may be necessary to divide
Safety Test Instrumentation Standards Committee
This SAE Standard specifies a procedure for approximating the volume of typical materials contained in the bowl of Open Bowl scrapers as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and representative volumes on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application
MTC1, Earthmoving Machinery
The purpose of this SAE standard is to define test conditions, describe tests to be made, specify data to be obtained, show formulas and calculations, define terms, and establish a uniform method of reporting so that performance data obtained on various makes and models of tractors, tested in accordance with this document, will be comparable regardless of where the tests are made. Because of the availability of many tractor models and types that can be equipped with a variety of special or optional equipment, the scope of this standard must be limited to obtaining and reporting only the most significant of widely used performance data. Test performed to either the Standard Code as outline in Section 4 or the Restricted Coed as outlined in Section 5 will satisfy requirements of this Agricultural Tractor Test Code. This document is technically equivalent to the OECD Tractor Test Code C(87)53, Annex I and Annex II. It is intended as a guide to development and pre-testing of tractors prior
ATSC Test Standards Subcommittee
This SAE Recommended Practice applies to mobile cranes when used in lifting crane service which are equipped with boom length indicating devices
Cranes and Lifting Devices Committee
This document was developed to provide a method of obtaining repeatable measurements that accurately reflects the performance of a propulsion electric drive subsystem, whose output is used in an electrified vehicle regardless of complexity or number of energy sources. The purpose is to provide a familiar and easy-to-understand performance rating. Whenever there is an opportunity for interpretation of the document, a good faith effort shall be made to obtain the typical in-service performance and characteristics and avoid finding the best possible performance under the best possible conditions. Intentional biasing of operating parameters or assembly tolerances to optimize performance for this test shall not be considered valid results in the scope of this document
Hybrid - EV Committee
Supplementary to the heat or cast analysis, a product analysis may be made on steel in the semifinished or finished form. For definitions and methods of sampling steel for product chemical analysis, refer to SAE J408. A product analysis is a chemical analysis of the semifinished or finished steel to determine conformance to the specification requirements. The range of the specified chemical composition is normally expanded to take into account deviations associated with analytical reproducibility and the heterogeneity of the steel. Individual determinations may vary from the specified heat or cast analysis ranges or limits to the extent shown in Tables 1 through 5. The several determinations of any element in a heat or cast may not vary both above and below the specified range except for lead. Tables 1 through 5 provide permissible limits for various steel forms and composition types. For rephosphorized and resulfurized steels, the product analysis tolerance limits are not applicable
Metals Technical Committee
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length
Signaling and Marking Devices Stds Comm
This SAE Standard applies to self-propelled sweepers and scrubbers as defined in SAE J2130-1 and J2130-2
MTC2, Sweeper, Cleaner, and Machinery
This document focuses on the latest in-force regulations. However, in addition to latest information, the report may include historical information. As regulations are superseded, the previous entry will remain to help understand the change in requirements over time. The initial focus of the document includes light-, medium-, and heavy-duty on-road vehicles with all propulsion systems. The document will include information from the United States and Canada, with later publications expanding to other regions. Forecasts for future regulations will not be included in the spreadsheet but be kept in a separate document. The document may be expanded to other types of applications/vehicles as information becomes available
null, null
The SAE Recommended Practice covers the application requirements for terminals and splice clips attached to stranded low tension wiring and cable as shown in SAE J1127 and SAE J1128. In addition, it covers maximum voltage drop limits for friction type connections
Connector Systems Standards Committee
This SAE Recommended Practice provides a minimum standard for evaluating squeeze-type resistance spot welding (STRSW) equipment and minimum weld performance criteria for two-sided automotive collision repair welding. This document contains several standardized test methods that are designed for evaluating equipment performance in a laboratory environment
Motor Vehicle Council
This SAE Standard provides test procedures and performance requirements for emergency warning devices (triangular shape), without self-contained energy sources, that are designed to be carried in motor vehicles and used to warn approaching traffic of the presence of a stopped vehicle, except for devices designed to be permanently affixed to the vehicle, and provides test procedures and performance requirements for protective containers for such emergency warning devices
Heavy Duty Lighting Standards Committee
This SAE Recommended Practice describes the test procedures for conducting rear impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mount testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included
Truck Crashworthiness Committee
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps intended for use on vehicles 2032 mm or more in overall width. Tail lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width
Heavy Duty Lighting Standards Committee
This SAE Standard applies to all combinations of pneumatic tires, wheels, or runflat devices (only as defined in SAE J2013) for military tactical wheeled vehicles only as defined in SAE J2013. This applies to original equipment and new replacement tires, retread tires, wheels, or runflat devices. This document describes tests and test methodology, which will be used to evaluate and measure tire/wheel/runflat system and changes in vehicle performance. All of the tests included in this document are not required for each tire/wheel/runflat assembly. The Government Tire Engineering Office and Program Office for the vehicle system have the responsibility for the selection of a specific test(s) to be used. The selected test(s) should be limited to that required to evaluate the tire/wheel/runflat system and changes in vehicle performance. Selected requirements of this specification shall be used as the basis for procurement of a tire, wheel, and/or runflat device for military tactical wheeled
Truck and Bus Tire Committee
This SAE Recommended Practice is applicable to all types of reciprocating engines including two-stroke cycle and free piston engines, and was prepared to facilitate clear understanding and promote uniformity in nomenclature. Modifying adjectives in some cases were omitted for simplicity. However, it is good practice to use adjectives when they add to clarity and understanding
SAE IC Powertrain Steering Committee
This information report is a companion document to SAE Recommended Practice J1376, Fuel Economy Measurement Test (Engineering Type) for Trucks and Buses. It provides background information and explanations to better understand the measurement procedure and its use. It also provides references and data which were developed by the SAE/DOT Program in support of the particular limitations or parameters selected for the various items in the test procedure. The format used in this document is similar to the recommended practice so that corresponding topics can be found under the same headings
Truck and Bus Aerodynamics and Fuel Economy Committee
This recommended practice describes a process for testing the comprehension of static (i.e., fixed or non-dynamic) symbols for all ground vehicles, for both OEM and aftermarket products. With advancing display technology, it is now possible to display dynamic symbols (e.g., a spinning beach ball to show that a process is ongoing, or a diagram showing energy distribution in hybrid vehicles). Such graphics are outside of the scope of this recommended practice, though extensions of this process may be useful for testing them. However, several symbols which occupy the same space on a display may change state without movement (e.g. play/pause button); these are within the scope of this recommended practice. The process described in this recommended practice includes criteria that are used to identify how well the perceived meaning matches the intended meaning for a representative sample of drivers. The data from this process are analyzed to determine the drivers’ comprehension of the symbol
Driver Vehicle Interface (DVI) Committee
This SAE Recommended Practice contains a series of test methods for use in measuring characteristics of automotive-type sealers, adhesives, and deadeners. The test methods which are contained in this document are as follows: ADS-1—Methods of Determining Viscosity ADS-2—Low Temperature Tests ADS-3—Weld-Through Tests ADS-4—Enamel, Lacquer, and Fabric Staining Test ADS-5—Wash-Off Resistance Test ADS-7—Solids Test ADS-8—Flash Point Test ADS-9—Sag and Bridging Tests ADS-10—Flow Test The intent of this document is to provide a series of test methods which can be used in testing the various qualities of sealers, adhesives, and deadener material. In later revisions of this document, attempts will be made to reduce the number of tests now presented. The specific temperatures and times at which some of these tests are to be conducted are not dictated in these test procedures, but they will be found in the material standards which govern each type of material to be tested
Materials, Processes and Parts Council
This SAE Recommended Practice promotes uniformity in the evaluation tests and performance measurements that are conducted on fuel injectors used in low-pressure gasoline engine applications. The scope of this document is limited to electronically actuated fuel injection devices that are utilized in automotive gasoline port fuel injection systems where the fuel supply pressure is normally less than 1000 kPa. Detailed test procedures are provided for determining numerous PFI injector parameters, including, but not limited to, flow curves, leakage, electromechanical performance, fluid compatibility and corrosion susceptibility, durability, the effects of vibration and torsional deflection, thermal cycling effects, and noise. The standardized measurement procedures in this document are all bench tests. Characterization of the fuel spray from a low-pressure gasoline port fuel injector is quite important; however, these spray characterization tests are not addressed in this document, but are
Gasoline Fuel Injection Standards Committee
This SAE Recommended Practice applies to upper coupler kingpins for commercial trailers and semitrailers conforming to the dimensional requirements of SAE J700 when new and originally installed. The dimensions of SAE J700 are the frame of reference for this document
Truck and Bus Total Vehicle Steering Committee
The purpose of this SAE Recommended Practice is to review factors that influence the behavior of elastomers under conditions of dynamic stress and to provide guidance concerning laboratory procedures for determining the fatigue characteristics of elastomeric materials and fabricated elastomeric components
Materials, Processes and Parts Council
Items per page:
1 – 50 of 207327