Results
This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine-driven cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depends on the volumetric flow rate, or the pressure rise across the fan, since these two
This specification covers bonded honeycomb core made of aluminum alloy and supplied in the form of blocks, slices, or other configurations as ordered (see 8.5
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.000 inch (25.40 mm) and under in nominal thickness
This specification covers a low-carbon steel in the form of wire up to 0.249 inch (6.32 mm), inclusive, supplied as coils of wire or, when specified, as straight lengths
This specification covers an aircraft-quality, corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings
The supplier shall use the following process to respond to a customer request for corrective and preventive action
This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance
The purpose of this SAE Recommended Practice is to establish reference standards for airflow measurements in the ranges required for testing automotive engine induction systems and to describe equipment that will facilitate the use of such standards to check the accuracy of various equipment and methods
This set of criteria is intended for use by accredited Certification Bodies (CBs) to establish compliance and grant certification to AS6081A. It may also be used by others to assess compliance to AS6081A requirements
This standard establishes requirements for Process Control Methods to sustain product conformity. This includes training, selection of control methods, analysis and improvement of their effectiveness, and subsequent monitoring and control. It applies to all controls documented in the Control Plan. This will include but is not limited to Key Characteristics (KCs) and Critical Items (CIs). This standard aligns and collaborates with the requirements of AS9100, AS9103, AS9145, AS13000, AS13002, AS13003, and AS13004. Commercial-Off-The-Shelf (COTS) items and Standard Catalogue Items (that neither the customer nor supplier hold design authority for) are not included
This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence
This specification covers the requirements for an electrodeposit of cadmium diffused into an electrodeposit of nickel on carbon, low-alloy, and corrosion-resistant steels
This specification covers the requirements for electrodeposition of tin on metals and the properties of the deposit
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock
This document establishes age limit and guidance for acceptance of hose and hose assemblies containing elastomeric materials for use in aircraft, space vehicles, missiles and component assemblies thereof at time of delivery to the contractor, procuring activity, or contracting officer. This document does not establish limitations on storage times for military/civil activities nor operating life
Define a process enabling network devices to detect the baud rate of a CAN Classic network as specified by physical layers SAE J1939-11, SAE J1939-14, or SAE J1939-15. The intent is to minimize or eliminate communication disruption between existing network devices. These networks only support Classical Base Frame Format (CBFF) and Classical Extended Frame Format (CEFF) Data Frames, as defined in ISO 11898-1:2015. Baud rate detection on a SAE J1939 CAN FD network is not in scope, as SAE J1939-17 is currently the only SAE J1939 CAN FD physical layer option and specifies only one supported baud rate combination (500 kbit/s / 2000 kbit/s
This SAE Aerospace Recommended Practice establishes the requirements and procedures for eddy current inspection of open fastener holes in aluminum aircraft structures
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, O-ring cord, compression seals, and molded-in-place gaskets for aeronautical and aerospace applications
This specification covers a precision cold-rolled corrosion- and heat-resistant nickel alloy in the form of sheet and strip over 0.005 to 0.015 inch (0.13 to 0.38 mm), inclusive, in nominal thickness and foil up to 0.005 inch (0.13 mm), inclusive, in nominal thickness (see 8.4
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems
This set of Abstract Syntax Notation (ASN.1) modules contains the precise definitions of data structures used in the SAE J3287 standard. Using the ASN.1 specification, a compiler tool can produce libraries that enable software applications to use the data structures and produce corresponding encodings using the Octet Encoding Rules (OER). For further information see the body of SAE J3287. You may also be interested in: V2X Misbehavior Reporting™ the J3287 PDF. V2X Misbehavior Reportingt™ SET File that includes the J3287 ASN File and the J3287 PDF (ZIP format) - download purchase only
This Abstract Syntax Notation (ASN.1) file precisely specifies the structure of the data used to support implementation of SAE International Standard J3217/R. Using the ASN.1 specification, a compiler tool can be used to produce encodings as required by the encoding rules identified in the standard (SAE J3217/R messages are encoded with UPER encoding). Both this file and the SAE J2735 ASN.1 files are necessary to collectively implement the data exchanges described in SAE J3217/R. The combined library can be used by any application (along with the additional logic of that application) to exchange the data using interfaces conformant to J3217/R. SAE J3217/R specifies interface requirements and message exchanges for configuration and reporting in road use charging systems
This SAE Recommended Practice describes how to position and posture the H-point design tool (HPD) described in Appendix B, and how to establish the seating reference point (SgRP), design H-point travel path, and other key reference points that are used in the design and specification of both driver and passenger seat positions. This practice also provides a method for determining the length of the seat track for a driver seat that adjusts fore/aft. The seat track length is based on a desired level of driver accommodation, assuming a U.S. population containing an equal number of male and female drivers. The procedure can be used to establish driver seat track accommodation for new vehicle designs or to evaluate accommodation in existing vehicles. A general method for determining driver seat track length for any driver population (male and female stature distribution) at any selected accommodation percentile and gender mix is given in Appendix A. Application of this document is limited
The scope of this SAE Recommended Practice is limited to cranes mounted on a fixed platform lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a work boat as defined in 3.14
This specification covers performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in road vehicle applications that are: low voltage (0 to 20 VDC) or Coaxial. Incomplete (mechanical) specifications for jacketed twisted pair connectors are also provided. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems. They are not applicable to Edge Board connector systems, twist-lock connector systems, >20 VAC or DC, or to eyelet terminals. No electrical connector, terminal, or related component may be represented as having met USCAR specifications unless conformance to all applicable requirements of this specification have been verified and documented. All required verification and documentation must be done by the supplier of the part or parts. If testing is performed by another source, it does not relieve the primary
The procedures contained in this specification cover the laboratory testing of replaceable halogen incandescent bulbs for use in automotive road illumination. The following tests are intended to be run under the following conditions. New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test The completion of one calendar year, accept as noted in the following Test Schedule Table. Test Title Yearly Physical Dimensions X Mean Spherical Candela (MSCD) X External Visual Examination X Color X Leak/Sealability Through Terminals and Seals X Deflection X Fluid Compatibility Terminal Retention X Resonant Frequencies Aged Resonant Frequency Salt Spray Outgassing Temperatures Requirement Laboratory Life at 14.0 VDC X Luminous Intensity Maintenance X Vibration Durability Shock Aged Vibration Durability Terminal Requirements DRL (SAE J2087
This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connectors, direct wire wedge base sockets, bayonet base sockets with integral connectors, direct wire bayonet base sockets, wedge base and bayonet base sockets with circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendices E and F whenever the following occurs: New design. Design, material, or process change made to an existing device, which could affect the outcome of the test. The test sequences shown in Appendix G shall be run annually
This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray, and different thicknesses of the holes that the clip is inserted into. Clips are typically inserted into sheet or rolled metal
This specification defines test methods and performance criteria for ultrasonically welded wire-to-terminal bonds as shown in Figure 1. This specification subjects parts to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures referenced in this specification include thermal shock, temperature humidity cycling, and mechanical stress. This specification is intended to evaluate the strength and performance of the interface between wires and the electrical terminal pad. The graphics used are specific to the linear weld type of process equipment. Validation of the terminal is a separate task (refer to a component validation test such as SAE/USCAR-2). If the weld under test (WUT) is different than described in this section or is subjected to conditions beyond what is typical of automotive use, the test sequence may not be applicable. Ensure that parts used in other conditions are validated for the actual conditions encountered. Vehicle and product
The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917
This document is a supplement to SAE/USCAR 17 and is intended to give recommended usages for one and two-way RF connectors and dimensional requirements for 2-way RF connectors and hybrid (RF & DC power) connectors which are not currently specified elsewhere. The radio frequency (RF) connector interface specified herein is suited for unsealed and sealed automobile applications up to 6 GHz and is intended for in-line, board mount, device mount, straight or angled applications. Dimensional requirements are specified in this document to ensure interchangeability. Compliance with the dimensional requirements of this specification will not guarantee interoperability between different suppliers mating connectors. It is the supplier responsibility to ensure RF performance requirements are met with other suppliers mating connectors. Performance requirements are specified in SAE/USCAR-2, and in SAE/USCAR-17
This test procedure is intended to evaluate and/or validate electrical ground schemes for use on the body or chassis. There are two classes based on the expected environmental conditions. Exposed Grounds can be located anywhere in the vehicle (except on the powertrain) and is the class for which most schemes should be tested. Unexposed Grounds can only be used in the passenger compartment or trunk and as such are special cases. This procedure as written is not intended for testing powertrain grounds where high temperatures and vibration levels may be encountered. These situations may require modifications to this procedure and are left to the Responsible Engineer to determine. This specification does not specifically address validation of terminal to wire electrical crimps. Crimps are tested to SAE/USCAR-21
The scope of this SAE Information Report is limited to a lift crane mounted on a fixed or floating platform, lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a workboat as defined in 3.15
Items per page:
50
1 – 50 of 209626