Results
This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine-driven cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depends on the volumetric flow rate, or the pressure rise across the fan, since these two
This specification covers an aircraft-quality, corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings
This specification covers bonded honeycomb core made of aluminum alloy and supplied in the form of blocks, slices, or other configurations as ordered (see 8.5
This specification covers a low-carbon steel in the form of wire up to 0.249 inch (6.32 mm), inclusive, supplied as coils of wire or, when specified, as straight lengths
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate 1.000 inch (25.40 mm) and under in nominal thickness
This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance
The supplier shall use the following process to respond to a customer request for corrective and preventive action
This specification covers the requirements for an electrodeposit of cadmium diffused into an electrodeposit of nickel on carbon, low-alloy, and corrosion-resistant steels
The purpose of this SAE Recommended Practice is to establish reference standards for airflow measurements in the ranges required for testing automotive engine induction systems and to describe equipment that will facilitate the use of such standards to check the accuracy of various equipment and methods
This specification covers the requirements for electrodeposition of tin on metals and the properties of the deposit
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock
This standard establishes requirements for Process Control Methods to sustain product conformity. This includes training, selection of control methods, analysis and improvement of their effectiveness, and subsequent monitoring and control. It applies to all controls documented in the Control Plan. This will include but is not limited to Key Characteristics (KCs) and Critical Items (CIs). This standard aligns and collaborates with the requirements of AS9100, AS9103, AS9145, AS13000, AS13002, AS13003, and AS13004. Commercial-Off-The-Shelf (COTS) items and Standard Catalogue Items (that neither the customer nor supplier hold design authority for) are not included
This set of criteria is intended for use by accredited Certification Bodies (CBs) to establish compliance and grant certification to AS6081A. It may also be used by others to assess compliance to AS6081A requirements
This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence
Define a process enabling network devices to detect the baud rate of a CAN Classic network as specified by physical layers SAE J1939-11, SAE J1939-14, or SAE J1939-15. The intent is to minimize or eliminate communication disruption between existing network devices. These networks only support Classical Base Frame Format (CBFF) and Classical Extended Frame Format (CEFF) Data Frames, as defined in ISO 11898-1:2015. Baud rate detection on a SAE J1939 CAN FD network is not in scope, as SAE J1939-17 is currently the only SAE J1939 CAN FD physical layer option and specifies only one supported baud rate combination (500 kbit/s / 2000 kbit/s
This document establishes age limit and guidance for acceptance of hose and hose assemblies containing elastomeric materials for use in aircraft, space vehicles, missiles and component assemblies thereof at time of delivery to the contractor, procuring activity, or contracting officer. This document does not establish limitations on storage times for military/civil activities nor operating life
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, O-ring cord, compression seals, and molded-in-place gaskets for aeronautical and aerospace applications
This SAE Aerospace Recommended Practice establishes the requirements and procedures for eddy current inspection of open fastener holes in aluminum aircraft structures
This specification covers a precision cold-rolled corrosion- and heat-resistant nickel alloy in the form of sheet and strip over 0.005 to 0.015 inch (0.13 to 0.38 mm), inclusive, in nominal thickness and foil up to 0.005 inch (0.13 mm), inclusive, in nominal thickness (see 8.4
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
The 3D crush model can be obtained by any suitable photogrammetry method using this image set and is intended to graphically represent in photographs the shape and orientation of the damaged surface(s) relative to the undamaged, or least damaged, portion of the vehicle. The procedure is intended to provide an image set sufficient to determine, with the use of photogrammetric methodologies, the 3D location of points on the crushed surface of the damaged vehicle. Measurement of the exterior damaged surface(s) on a vehicle is a necessary step in quantifying the deformation caused by a collision and the energy dissipated by the deformation process. The energy analysis is sometimes called a crush analysis. Evaluation of the energy dissipated is useful in reconstructing the change in the velocity of the vehicles (delta-V) involved in a collision. This guideline is intended for use by investigators who do not have photogrammetry expertise, special equipment or training and may be constrained
This SAE Recommended Practice describes methods for determining total and specular reflectance for mirrors with flat and curved surfaces and a method for determining diffuse reflectance and haze for mirrors with flat surfaces
This specification defines test methods and performance criteria for ultrasonically welded wire-to-terminal bonds as shown in Figure 1. This specification subjects parts to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures referenced in this specification include thermal shock, temperature humidity cycling, and mechanical stress. This specification is intended to evaluate the strength and performance of the interface between wires and the electrical terminal pad. The graphics used are specific to the linear weld type of process equipment. Validation of the terminal is a separate task (refer to a component validation test such as SAE/USCAR-2). If the weld under test (WUT) is different than described in this section or is subjected to conditions beyond what is typical of automotive use, the test sequence may not be applicable. Ensure that parts used in other conditions are validated for the actual conditions encountered. Vehicle and product
This SAE Recommended Practice establishes uniform procedures for assuring the manufactured quality, installed utility, and service performance of manual automotive adaptive products, other than those provided by the OEM, intended to provide driving capability for persons with physical disabilities. These devices function as adaptive appliances to compensate for lost or reduced performance in the drivers’ arms or legs, or both. Some of the devices are designed to transfer foot functions to the hands, hand functions to the feet, or functions from one side of the body to the other. This document applies only to primary controls as defined in 3.4.1 and in the Foreword. In particular, this document is specifically concerned with those mechanical and hybrid products that are intended by the manufacturer of the adaptive product to: Be installed within the occupant space of the vehicle Be operated by a vehicle driver with a physical disability Be added to, or substituted for, the OEM vehicle
This SAE Standard is intended to provide personnel protection guidelines for skid steer loaders. This document is intended as a guide towards standard practice, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. This document provides performance criteria for newly manufactured loaders and it is not intended for in-service machines
The SAE J2954 standard establishes an industry-wide specification that defines acceptable criteria for interoperability, electromagnetic compatibility, EMF, minimum performance, safety, and testing for wireless power transfer (WPT) of light-duty plug-in electric vehicles. The specification defines three charging levels up to 11 kVA and in future revisions up to 22 kVA. A standard for WPT based on these charge levels enables selection of a charging rate based on vehicle requirements, thus allowing for better vehicle packaging and ease of customer use. This is meant to be used in conjunction with communications standard SAE J2847/6 and use cases J2836/6 and ground assembly WPT Certification UL 2750. The specification supports home (private) charging and public wireless charging. In the near term, vehicles that are able to be charged wirelessly under SAE J2954 should also be able to be charged conductively by SAE J1772 plug-in chargers. This standard addresses stationary light-duty
This practice applies to guarding of engine cooling fans used on Off-Road Self-Propelled Work Machines defined in SAE J1116. It does not include guarding for belts, pulleys, or other rotating equipment used on these machines
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a Ability of the parking brake system to lock the braked wheels. b The trailer holding or sliding on the grade, fully loaded, or unloaded. c Applied manual effort. d Unburnished or burnished brake lining friction conditions. e Down and upgrade directions
This SAE Recommended Practice is applicable to two- or three-wheel motorcycles intended for highway use. Unless noted, requirements apply to both metallic and nonmetallic tanks. Accessory or aftermarket tanks as well as original equipment tanks are covered
This SAE Standard characterizes grapple skidders and identifies the major components and parts most commonly associated therewith. Illustrations used herein are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been included to facilitate application of this document
This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853
Items per page:
50
1 – 50 of 209626