Your Selections

TEVTDTS9
Show Only

Collections

File Formats

Content Types

Dates

Sectors

Topics

Publishers

Committees

Committee Codes

Companion Flanges, Type A (External Pilot) and Type S (Internal Pilot)

Driveline Standards Committee
  • Ground Vehicle Standard
  • J1946_200106
  • Historical
Published 2001-06-25 by SAE International in United States
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.

Universal Joints and Driveshafts--Nomenclature--Terminology--Application

Driveline Standards Committee
  • Ground Vehicle Standard
  • J901_200012
  • Historical
Published 2000-12-01 by SAE International in United States
The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see Universal Joint and Driveshaft Design Manual, AE-7.

Front-Wheel-Drive Constant Velocity Joint Boot Seals

Driveline Standards Committee
  • Ground Vehicle Standard
  • J2028_200005
  • Historical
Published 2000-05-17 by SAE International in United States
This SAE Recommended Practice outlines the qualification testing and performance related criteria of elastomeric boot seals used in constant velocity joint applications. These applications are referred to as front- wheel-drive halfshafts or axles, but can also be utilized in rear-wheel-drive halfshaft applications. For additional information regarding CV joint systems and their applications refer to SAE AE-7 "Universal Joint and Driveshaft Design Manual." The grease type and grease quantities, clamps and clamping mechanisms of an assembly are critical and considered to be the same as OEM, service, or aftermarket designation. Although joint lubricating grease and clamping mechanism are not addressed in this document, they are critical to a total system performance. The purpose of this document is to establish a uniform practice for those in the surface vehicle industry that specify and/or manufacture CV joint boot seals (boots) for OEM or aftermarket use with respect to qualification testing for physical and mechanical properties. This document is not intended to include or address propeller shaft, Power Take Off, heavy equipment, and marine boot seal applications.

Cross-Tooth Companion Flanges, Type T

Driveline Standards Committee
  • Ground Vehicle Standard
  • J1945_200004
  • Historical
Published 2000-04-28 by SAE International in United States
This SAE Standard specifies the nominal dimensions and tolerances which affect interchangeability between cross-tooth companion flanges type T and mating parts. Dimensions and tolerances of the mating parts, other than those occurring at the interface of the two flanges, are left to the discretion of the manufacturer of that component. This document is equivalent to ISO 8667-1992.

Front-Wheel-Drive Constant Velocity Joint Boot Seals

Driveline Standards Committee
  • Ground Vehicle Standard
  • J2028_199206
  • Historical
Published 1992-06-01 by SAE International in United States
This SAE Recommended Practice outlines recommended practices for qualification testing and performance related criteria of elastomeric boot seals integral to constant velocity joint applications in surface vehicles. Typically, these applications are referred to as front-wheel-drive halfshafts or axles, but can also be utilized in rear-wheel-drive halfshafts and propeller shaft applications. For additional information regarding CV joint systems and their applications refer to SAE AE-7 "Universal Joint and Driveshaft Design Manual." The grease quantities, clamps, and clamping mechanisms of an installation are considered to be the same as OEM or service designation. They are to be adequate and are not addressed in this document.

Companion Flanges, Type A (External Pilot) and Type S (Internal Pilot)

Driveline Standards Committee
  • Ground Vehicle Standard
  • J1946_199101
  • Historical
Published 1991-01-31 by SAE International in United States
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.

Companion Flanges, Type A (External Pilot) and Type S (Internal Pilot)

Driveline Standards Committee
  • Ground Vehicle Standard
  • J1946_199006
  • Historical
Published 1990-06-01 by SAE International in United States
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.

Cross-Tooth Companion Flanges, Type T

Driveline Standards Committee
  • Ground Vehicle Standard
  • J1945_199001
  • Historical
Published 1990-01-01 by SAE International in United States
This SAE Standard specifies the nominal dimensions and tolerances which affect interchangeability between cross-tooth companion flanges type T and mating parts. Dimensions and tolerances of the mating parts, other than those occurring at the interface of the two flanges, are left to the discretion of the manufacturer of that component. This document is equivalent to ISO 8667-1992.

Universal Joints and Driveshafts--Nomenclature--Terminology--Application

Driveline Standards Committee
  • Ground Vehicle Standard
  • J901_198503
  • Historical
Published 1985-03-01 by SAE International in United States
The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see Universal Joint and Driveshaft Design Manual, AE-7.

Universal Joints and Driveshafts--Nomenclature--Terminology--Application

Driveline Standards Committee
  • Ground Vehicle Standard
  • J901A_196708
  • Historical
Published 1967-08-01 by SAE International in United States
The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see Universal Joint and Driveshaft Design Manual, AE-7.