Your Selections

TETES2
Show Only

Collections

File Formats

Content Types

Dates

Sectors

Topics

Publishers

Committees

Committee Codes

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2698_201810
  • Current
Published 2018-10-04 by SAE International in United States
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
Datasets icon
Annotation icon

Combination 11 Conductors and 2 Pairs ECBS Cable

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2742_201806
  • Current
Published 2018-06-03 by SAE International in United States
This SAE standard establishes the minimum construction and performance requirements for a combination cable consisting of 11 conductors and 2 twisted pairs for use on trucks, trailers, and dollies in conjunction with SAE J2691. (15 pole connectors.) The cable includes both power and unjacketed SAE J1939-15 paired signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Datasets icon
Annotation icon

Accelerator Pedal Position Sensor for Use with Electronic Controls in Medium- and Heavy-Duty Vehicle Applications—Truck and Bus

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J1843_201805
  • Current
Published 2018-05-24 by SAE International in United States
The purpose of this SAE Recommended Practice is to provide a common electrical and mechanical interface specification that can be used to design electronic accelerator pedal position sensors and electronic control systems for use in medium- and heavy-duty vehicle applications.
Annotation icon

Truck Tractor Power Output for Trailer ABS

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2247_201805
  • Current
Published 2018-05-24 by SAE International in United States
This SAE Recommended Practice identifies the minimum truck tractor electrical power output of the stop lamp and ABS (antilock brake system) circuits measured at the primary SAE J560 tractor trailer interface connector(s).
Datasets icon
Annotation icon

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2691_201804
  • Current
Published 2018-04-15 by SAE International in United States
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Datasets icon
Annotation icon

Coiled Electrical Cable - Truck and Bus

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2222_201802
  • Current
Published 2018-02-15 by SAE International in United States
This SAE Standard establishes the minimum performance and endurance requirements for coiled electrical cables used for hookup between trucks, trailers and dollies. The component standards SAE J2394 (replaced SAE J1067) for cable and SAE J560 for connectors must be consulted to determine the complete performance and endurance requirements of the system. Related TMC Recommended Practices may be consulted for information associated with selection, installation and inspection of these coiled electrical cables. This document is intended to set out requirements for the majority of conditions rather than for specialized applications or environments.
Datasets icon
Annotation icon

Seven Conductor Cable for ABS Power - Truck and Bus

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2394_201712
  • Current
Published 2017-12-20 by SAE International in United States
This SAE standard establishes the minimum construction and performance requirements for seven conductor 1/8-2/10-4/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
Datasets icon
Annotation icon

Recommended Environmental Practices for Electronic Equipment Design in Heavy-Duty Vehicle Applications

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J1455_201703
  • Current
Published 2017-03-17 by SAE International in United States
The scope of this Recommended Practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment, and agricultural equipment including implements.
Datasets icon
Annotation icon

Inverter Requirements for Class Eight Trucks - Truck and Bus

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J2697_201702
  • Current
Published 2017-02-07 by SAE International in United States
This SAE Recommended Practice is intended to describe the application of single-phase DC to AC inverters, and bidirectional inverter/chargers, which supply power to ac loads in Class heavy duty on-highway trucks (10K GVW). The document identifies appropriate operating performance requirements and adds some insight into inverter selection. This document applies to factory and after-market installed DC-to-AC inverter systems (Including inverter chargers) providing up 3000 W of 120 VAC line-voltage power as a convenience for operator and passenger use. Such inverters are intended to power user loads not essential to vehicle Operation or safety (e.g., HVAC, TV, microwave ovens, battery chargers for mobile phones or laptop computers, audio equipment, etc.). Systems incorporate the inverter itself as well as the input, output, control, and signal wiring associated with the inverter. Requirements are given for the performance, safety, reliability, and environmental compatibility of the system. These are recommended requirements to be used by vehicle manufacturers in the development of their own specifications, which may incorporate more or less stringent requirements. This document scope excludes military vehicles, bus and…
Datasets icon
Annotation icon

Seven Conductor Cable - Truck and Bus

Truck and Bus Electrical Systems Committee
  • Ground Vehicle Standard
  • J1067_201610
  • Current
Published 2016-10-25 by SAE International in United States
This SAE standard establishes the minimum construction and performance requirements for seven conductor 1/8-1/10-5/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications.
Datasets icon
Annotation icon