Your Selections

TETCHS3
Show Only

Collections

File Formats

Content Types

Dates

Sectors

Topics

Publishers

Committees

Committee Codes

   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1671_201910
  • Current
Published 2019-10-17 by SAE International in United States
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Setting Preload in Heavy-Duty Wheel Bearings

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J2535_201910
  • Current
Published 2019-10-07 by SAE International in United States
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J2696_201909
  • Current
Published 2019-09-03 by SAE International in United States
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less-common applications are not covered.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Fastener Hardware for Wheels for Demountable Rims

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1835_201906
  • Current
Published 2019-06-17 by SAE International in United States
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Wheels/Rims - Military Vehicles Test Procedures and Performance Requirements

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1992_201906
  • Current
Published 2019-06-06 by SAE International in United States
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

ABS Exciter Ring Location Standardization

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1730_201902
  • Current
Published 2019-02-11 by SAE International in United States
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1842_201808
  • Current
Published 2018-08-08 by SAE International in United States
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Nomenclature - Wheels, Hubs, and Rims for Commercial Vehicles

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J393_201710
  • Current
Published 2017-10-23 by SAE International in United States
This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Road Vehicles - Wheels for Commercial Vehicles and Multipurpose Passenger Vehicles - Fixing Nuts - Test Methods

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1965_201710
  • Current
Published 2017-10-03 by SAE International in United States
This SAE Recommended Practice applies to fasteners/fixing nuts as specified in SAE J694 and SAE J1835 used for disc wheels and demountable rim attachment respectively. Only the test methods necessary to ensure proper wheel or rim assembly are specified. Fasteners for less common and special applications are not included.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Dimensional Compatibility for Commercial Vehicles Fitment of Complete Wheels in Drum Brake Applications - Truck and Bus

Truck and Bus Wheel Committee
  • Ground Vehicle Standard
  • J1865_201607
  • Current
Published 2016-07-01 by SAE International in United States
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 inch, 22.5 inch, and 24.5 inch diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The lines provided establish the maximum envelope for brakes, including all clearances, and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
This content contains downloadable datasets
Annotation ability available