Your Selections
TEMSFCCS2
Filters
Collections
File Formats
Content Types
Dates
Sectors
Topics
Publishers
Committees
Committee Codes
Qualified Hoses for Marine Applications
- Ground Vehicle Standard
- J1942/1_201812
- Current
Published
2018-12-31
by SAE International in United States
The following list consists of hose data provided as of December 2018, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document.
Clip Fastener Fitting
- Ground Vehicle Standard
- J1467_201808
- Current
Published
2018-08-24
by SAE International in United States
This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.
Qualified Hoses for Marine Applications
- Ground Vehicle Standard
- J1942/1_201712
- Historical
Published
2017-12-27
by SAE International in United States
The following list consists of hose data provided as of December 2017, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document.
Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies
- Ground Vehicle Standard
- J343_201712
- Current
Published
2017-12-20
by SAE International in United States
This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.
Hydraulic Hose
- Ground Vehicle Standard
- J517_201710
- Current
Published
2017-10-18
by SAE International in United States
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document (see Tables 1 and 2). This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values. When using SAE J517 hose for marine applications, reference SAE J1475, SAE J1942, and SAE J1942-1. The SAE J517 100R9, 100R10, and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C. The SAE J517 100R1A, 100R2A, 100R2B, and 100R 2BT are discontinued due to lack of demand. For DOD orders replace 100R1A…
Automotive Air Brake Hose and Hose Assemblies
- Ground Vehicle Standard
- J1402_201710
- Current
Published
2017-10-12
by SAE International in United States
This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.
Hose Assemblies, Rubber, Hydraulic, Steel Wire Reinforced - Part 1: Procurement Document
- Ground Vehicle Standard
- J1754/1_201707
- Current
Published
2017-07-14
by SAE International in United States
This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See Part 2, Table 7 for hose operating temperature ranges and identification codes. NOTE: Working pressure is defined as maximum system pressure.
Hydraulic Flanged Tube, Pipe, and Hose Connections, 4-Screw Flange Connection Part 2: 42 MPa (Code 62)
- Ground Vehicle Standard
- J518/2_201704
- Current
Published
2017-04-13
by SAE International in United States
This SAE Standard covers general and dimensional specifications for the Code 62 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS and FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design. The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. THE FOLLOWING GENERAL SPECIFICATIONS SUPPLEMENT THE DIMENSIONAL DATA CONTAINED IN THE TABLES WITH RESPECT TO ALL UNSPECIFIED DETAIL. PARTS MANUFACTURED TO THIS STANDARD ARE INTERCHANGEABLE WITH ISO 6162-2 AND CONNECTORS TO EITHER STANDARD CAN BE SUPPLIED WITH THE EXCEPTION OF THE…
Optional Test Procedures for Hydraulic Hose Assemblies
- Ground Vehicle Standard
- J1405_201701
- Current
Published
2017-01-04
by SAE International in United States
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses.Basic test procedures are to be in accordance with SAE J343 except as modified in this document.
Qualified Hoses for Marine Applications
- Ground Vehicle Standard
- J1942/1_201612
- Historical
Published
2016-12-20
by SAE International in United States
The following list consists of hose data provided as of December 2016, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results. All sizes should be included in the same letter which must also include all of the information necessary to make a SAE J1942-1 listing. c The SAE will review the letter and may, at their discretion, request to see further test results. A copy of the submittal…