Your Selections

TEMFF
Show Only

Collections

File Formats

Content Types

Dates

Sectors

Topics

Publishers

Committees

Committee Codes

   This content is not included in your SAE MOBILUS subscription, or you are not logged in.
new

Protective Coatings for Fasteners

Fasteners Committee
  • Ground Vehicle Standard
  • J1648_201910
  • Current
Published 2019-10-07 by SAE International in United States

This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsiblity for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement.

   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

Fasteners Committee
  • Ground Vehicle Standard
  • J174_201908
  • Current
Published 2019-08-07 by SAE International in United States

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.

   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Tension Indicating Washer Tightening Method for Fasteners

Fasteners Committee
  • Ground Vehicle Standard
  • J2486_201804
  • Current
Published 2018-04-24 by SAE International in United States
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Torque-Tension Tightening for Metric Series Fasteners

Fasteners Committee
  • Ground Vehicle Standard
  • J1701M_201711
  • Current
Published 2017-11-08 by SAE International in United States
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers a number of the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of tightening tools or equipment used. Also described in this document is the torque management required to achieve satisfactory fastened joint tightening. This guide is limited in application to clearance fit threads, such as the common 6g/6H class of fit. Other thread types including interference fit, mechanical locking, prevailing torque, or forms other than ISO-Metric may apply to some aspects of this standard but are not specifically covered. The procedures described in this document are based on general principles for the determination of the torque-tension relationship for the use of end users. This is a guide and is not intended to be made a procurement requirement. For critical joint design the assembly torque values should be determined…
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Metric Thread Rolling Screws

Fasteners Committee
  • Ground Vehicle Standard
  • J1237_201709
  • Current
Published 2017-09-07 by SAE International in United States
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Mechanical and Material Requirements for Steel Nuts

Fasteners Committee
  • Ground Vehicle Standard
  • J995_201707
  • Current
Published 2017-07-20 by SAE International in United States
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Nut and Conical Spring Washer Assemblies

Fasteners Committee
  • Ground Vehicle Standard
  • J238_201705
  • Current
Published 2017-05-30 by SAE International in United States
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Torque-Tension Tightening for Inch Series Fasteners

Fasteners Committee
  • Ground Vehicle Standard
  • J1701_201702
  • Current
Published 2017-02-09 by SAE International in United States
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of wrenching employed. Also, described in this document is the torque management required to achieve correct fastener joint tightening. The thread fit of fasteners must be in accordance with Class 2A for external and Class 2B for internal inch threads.
This content contains downloadable datasets
Annotation ability available
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Blind Rivets - Break Mandrel Type

Fasteners Committee
  • Ground Vehicle Standard
  • J1200_201701
  • Current
Published 2017-01-04 by SAE International in United States
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
   This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Surface Discontinuities on Nuts

Fasteners Committee
  • Ground Vehicle Standard
  • J122_201701
  • Current
Published 2017-01-04 by SAE International in United States
This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.