This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Standard for Compressed Natural Gas Vehicle Fuel
- Ground Vehicle Standard
- J1616_201605
- Revised
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
Compressed Natural Gas (CNG) is a practical automotive fuel, with advantages and disadvantages when compared to gasoline. Large quantities of natural gas are available in North America. It has a higher octane number rating, produces low exhaust emissions, no evaporative emissions and can cost less on an equivalent energy basis than other fuels. Natural gas is normally compressed from 20 684 to 24 821 kPa (3000 to 3600 psig) to increase its energy density thereby reducing its on-board vehicle storage volume for a given range and payload. CNG can also be made from liquefied natural gas by elevating its pressure and vaporizing it to a gas. Once converted it is referred to LCNG.
The properties of natural gas are influenced by: (1) source of supply i.e. field, composition or impurities; (2) the processing of natural gas by the production and transmission companies; (3) the regional gas supply, storage, and demand balancing done by distribution companies often in concert with pipeline companies to maintain uninterrupted service throughout the year, e.g., peak shaving with propane-air (see U.S. Bureau of Mines Publication 503); and (4) dispensing site maintenance characteristics i.e. filtration and drying.
The Coordinating Research Council (CRC) has published the results of a national compressed natural gas vehicle fuel survey. Information on the properties of distribution system natural gas and its variability has been included in Figure 1, 2, and 3, and can be found in CRC Report No. PC-2-12. Composition can vary hourly under certain operating conditions in certain areas of the country. Thus the data should generally be considered representative for the areas mentioned with due consideration for local variation.
Natural gases transported throughout the U. S. are not subject to uniform national standards. Under federal government rules covering interstate sales of natural gas, the U. S. Federal Energy Regulatory Commission (FERC) adjudicates tariffs, placing economic and technical requirements upon natural gases entering interstate commerce. In 2006, FERC issued a policy statement advising stakeholders that:
-
1
Only natural gas quality and interchangeability specifications contained in FERC-approved gas tariffs can be enforced;
-
2
Pipeline tariff provisions on gas quality and interchangeability need to be flexible to allow pipelines to balance safety and reliability concerns;
-
3
Pipelines and their customers should develop gas quality and interchangeability specifications based on technical requirements;
-
4
In negotiating technically-based solutions, pipelines and their customers are strongly encouraged to use the Natural Gas Council Plus (NGC+) Interim Guidelines…as a common reference point for resolving gas quality and interchangeability issues; and
-
5
To the extent pipelines and their customers cannot resolve disputes over gas quality and interchangeability, those disputes can be brought before FERC to be resolved on a case-by-case basis…1
The NGC+ Interim Guidelines call for natural gas specifications that include:
-
1
A range of plus or minus 4% Wobbe number variation from local historical average gas, or alternatively, established adjustment or target gas for the service territory, subject to:
-
a
Maximum Wobbe number limit: 1400
-
b
Maximum higher heating value limit: 1110 Btu/scf
-
a
-
2
Additional composition maximum limits:
-
a
Maximum butanes+: 1.5 mole percent
-
b
Maximum total inerts: 4 mole percent
-
a
-
3
EXCEPTION: Service territories with demonstrated experience with supplies exceeding these Wobbe, higher heating value and/or compositional limits may continue to use supplies conforming to this experience as long as it does not unduly contribute to safety and utilization problems of end use equipment.2
While the Interim Guidelines provide only guidance for the setting of tariff limits on gas quality, experience has shown that in most cases the Wobbe and higher heating value limits are used in interstate tariffs. Since the bulk of U. S. sales of natural gas fall under FERC jurisdiction, this means that the Interim Guideline limits represent, in most cases, the limits that apply to natural gases received by distribution systems. Intrastate natural gas sales, by contrast, are not within FERC jurisdiction, but customers including utilities receiving gases from both intrastate and interstate sources, for practical purposes, generally receive natural gas that meets the Interim Guidelines.
The NGC+ Interim Guidelines address combustion issues associated with natural gases. Separately, FERC considered condensable hydrocarbons in response to a second paper from NGC+.3 No specific actions were recommended by FERC in response to the NGC+ recommendations from this report, which basically recommended translation of historical condensable hydrocarbon experience into more general phase diagram-depicted “cricondentherm hydrocarbon dew point” (CHDP) criteria for higher hydrocarbon mixtures. CHDP criteria help ensure that natural gases of various compositions remain in gaseous state at all operating pressures and all reasonable ambient temperatures.
Natural gas is comprised chiefly of methane (generally 88 to 96 mole percent) with the balance being a decreasing proportion of proportion of higher hydrocarbon alkanes such as ethane, propane, and butane. It can also contain nitrogen, water, carbon dioxide, oxygen, sulfur compounds and trace amounts of lubricating oil. At the retail outlet a warning agent, or odorant, is likely present in natural gas.
Experience with natural gas vehicles has grown considerably. Fleet and ongoing in-use applications provide a foundation for characterizing gas composition factors that will help to understand gas quality effects on vehicle and overall performance and may cause fundamental operational problems for natural gas vehicles (NGVs). Water content and other corrosion precursors, heavier hydrocarbons, which may condense within the fuel container, particulate matter, oil, and energy content all need to be considered. Condensable hydrocarbons (liquid state) are also of concern in NGV equipment degradation.
Rationale
This standard sets minimum requirements for compressed natural gas as a surface vehicle fuel for vehicle, engine, and component durability, operating safety, and design performance over the breadth of vehicle applications intended to utilize this fuel.
Recommended Content
| Ground Vehicle Standard | Recommended Practice for Compressed Natural Gas Vehicle Fuel |
| Technical Paper | Measured and Predicted Soot Particle Emissions from Natural Gas Engines |
| Technical Paper | HCNG Evaluation Using a Sequential Gas Injection System for a Passenger Car |
Topic
Data Sets - Support Documents
| Title | Description | Download |
|---|---|---|
| Unnamed Dataset 1 | ||
| Unnamed Dataset 2 | ||
| Unnamed Dataset 3 | ||
| Unnamed Dataset 4 | ||
| Unnamed Dataset 5 | ||
| Unnamed Dataset 6 | ||
| Unnamed Dataset 7 | ||
| Unnamed Dataset 8 | ||
| Unnamed Dataset 9 | CNG Fuels – Reference CRC Report No. E-109 Table 7 | |
| Unnamed Dataset 10 | Methane Number Calculations for CRC test fuels | |
| Table D.1 | Carb certification CNG chemical composition | |
| Table D.2 | Carb commercial CNG chemical composition | |
| Unnamed Dataset 13 | Table 1 of §1065.715—Test Fuel Specifications for Natural Gas |
Issuing Committee
Fuels and Lubricants TC 7 Fuels Committee
The Fuels Technical Committee 7 is responsible for the development of SAE Standards, Recommended Practices, Information Reports and related information pertinent to the technical aspects of fuels for internal combustion engines used in ground vehicles. The Truck and Bus J1616 Task Force has been formed under the committee's direction. Participants in the SAE Fuels Technical Committee include OEMs, suppliers, consulting firms, government and other interested parties.
Reference
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.