This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Safety Standards for Motor Vehicle Refrigerant Vapor Compression Systems
- Ground Vehicle Standard
- J639_201112
- Revised
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
This SAE Standard applies to refrigerant vapor compression systems that provide cooling and/or heating for passenger cars, light trucks and commercial vehicles (on and off road) that use automotive type mobile air conditioning [MAC] systems. Large trucks, buses and other vehicles that do not use typical automotive a/c systems or use refrigerants not listed in this document are not covered by this standard. This standard covers any vehicle with a MAC system using a belt or electric motor driven compressor.
This document provides standards for design, assembly, test and service of MAC systems to minimize environmental, health and safety impacts. Also included are cautionary statements for the service industry to alert technicians to the inadvisability and possible health or safety effects associated with venting refrigerant during service. It is not intended to restrict the use, or further development, of other types of refrigeration systems for mobile air conditioning applications. This document may be amended or additional safety standards created should other systems become practical. This document addresses only HFC-134a (R-134a), carbon dioxide (R-744), and HFO-1234yf (R-1234yf) refrigerants. To prevent system contamination all refrigerants used in mobile air conditioning vapor compression systems require unique service fittings and service equipment. The unique service fittings are intended to eliminate the potential for system refrigerant cross-contamination during service activity.
CFC-12 (R-12) is no longer in use in new MAC systems. The service fitting description is maintained as a reference for older vehicles still in use. When retrofitting an R-12 system to use R-134a or when removing R-12 (vehicle disposal) use service equipment designed for R-12 and certified to meet the requirements of SAE J1990 (R-12 recovery and recycle equipment).
HFC-152a is an A2 flammable refrigerant as classified by ASHRAE 34 and should be used only with a secondary loop application. However, until MAC systems are developed to use R-152a (HFC-152a), no SAE Standards for system design, service equipment or service procedures have been established. The R-152a service fittings described within this Standard were established as part of the industries evaluation of replacement refrigerants and are maintained for future design guidance and to prevent potential refrigerant cross contamination.
Rationale
This document covers refrigerant system design and safety related requirements for refrigerants used in mobile air conditioning (MAC) systems and is being revised to comprehend R-1234yf. The current wording of 4.1.1 prohibits refrigerants that are rated less than A2L which would exclude R-152a. Later in the document, J639 defines the fittings for R-152a. The intent of this revision is to insure safe mobile air conditioning systems by forcing proper risk assessments and appropriate design solutions while correcting this conflict with regards to R152a.
Recommended Content
Topic
Data Sets - Support Documents
| Title | Description | Download |
|---|---|---|
| Unnamed Dataset 1 | ||
| Unnamed Dataset 2 | ||
| Unnamed Dataset 3 | ||
| Unnamed Dataset 4 | ||
| Unnamed Dataset 5 | ||
| Unnamed Dataset 6 | ||
| TABLE 1 | REFRIGERANT SERVICE PORT FITTING DIMENSIONS |
Issuing Committee
Interior Climate Control Vehicle OEM Committee
The Interior Climate Control OEM Committee is responsible for developing and maintaining SAE Standards, Recommended Practices, and Information Reports that serve as guidelines for technicians who service mobile air conditioning systems and operate refrigerant recycling equipment as it applies to automobiles, light trucks and other vehicles with similar R12 systems. Participants in the SAE Interior Climate Control Standards Committee include OEMs, suppliers, consulting firms, government, and other interested parties.
Reference
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.