This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Low Water Tolerant Brake Fluids
- Ground Vehicle Standard
- J1705_200707
- Noncurrent
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
This SAE Recommended Practice was prepared by the Motor Vehicle Brake Fluids Subcommittee of the SAE Hydraulic Brake Actuating Systems Committee to provide engineers, designers, and manufacturers of motor vehicles with a set of minimum performance standards in order to assess the suitability of silicone and other low water tolerant type brake fluids (LWTF) for use in motor vehicle brake systems. These fluids are designed for use in braking systems fitted with rubber cups and seals made from natural rubber (NR), styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
In the development of the recommended requirements and test procedures contained herein, it is concluded that the LWTFs must be functionally compatible with existing motor vehicle brake fluids conforming to SAE J1703 and with braking systems designed for such fluids. To utilize LWTFs to the fullest advantage, they should not be mixed with other brake fluids. Inadvertent mixtures of LWTFs with fluids meeting SAE J1703 are not known to have any adverse effects on performance, but all combinations have not been tested. Vehicle manufacturer's recommendations should be followed where indicated. These fluids are not necessarily suitable for use in central hydraulic or pumped systems and are not intended for use below temperatures of −50 °C (−58 °F). Brake fluids covered under this document are not required to tolerate water and extreme caution should be exercised to prevent accidental entry of water which might lead to brake failure. Other performance characteristics of these LWTFs not covered in this document are discussed in Appendix A.
Rationale
This document has been found to be Noncurrent, therefore, it may be in use by some areas of industry but is not the most up-to-date technical information.
Recommended Content
| Ground Vehicle Standard | Motor Vehicle Brake Fluid |
| Ground Vehicle Standard | Motor Vehicle Brake Fluid Based Upon Glycols, Glycol Ethers, and the Corresponding Borates |
Topic
Data Sets - Support Documents
| Title | Description | Download |
|---|---|---|
| TABLE 1 | CORROSION TEST STRIPS AND MASS CHANGES | |
| TABLE 2 | EFFECT ON RUBBER |
Issuing Committee
Brake Fluids Standards Committee
The scope of the Brake Fluids Standards Committee is to develop and maintain relevant standards; recommended practices and information reports related to non-petroleum based brake fluids covering: The requirements of fluids for use in the hydraulic brake systems of motor vehicles; the handling, dispensing, and packaging of such fluids; service maintenance using such fluids. These documents are reviewed on a regular basis to ensure that they reflect the changing needs and requirements of the industry.
Reference
| Number | Title |
|---|---|
| ASTMD1120 | This document is not part of the subscrption. |
| ASTMD1415 | This document is not part of the subscrption. |
| ASTMD2240 | This document is not part of the subscrption. |
| ASTMD445 | This document is not part of the subscrption. |
| ASTMD91 | This document is not part of the subscrption. |
| ASTME1 | This document is not part of the subscrption. |
| ASTME145 | This document is not part of the subscrption. |
| ASTME203 | This document is not part of the subscrption. |
| FMVSS116 | Motor Vehicle Brake Fluids |
| J1703_201408 | Motor Vehicle Brake Fluid |
| MIL-B-46176 | This document is not part of the subscrption. |
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.