This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
GASKET, FITTING END, 37° FLARED
- Aerospace Standard
- AS4824B
- Revised
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Rationale
ADDITION OF THE OPTION TO ARGON QUENCH NICKEL AND CORROSION RESISTANT STEEL DURING THE HEAT TREATMENT PROCESS SO THAT A VENDOR’S CURRENT PROCESS MAY BE USED.
Recommended Content
Aerospace Material Specification | Rubber: Acrylonitrile-Butadiene (NBR) Engine Oil Resistance, 65 to 75 Hardness, for Seals in Aircraft Engine Oil Systems |
Aerospace Standard | FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI /9/ |
Aerospace Standard | GASKET, FITTING END, 24° CONE |
Topic
Data Sets - Support Documents
Title | Description | Download |
---|---|---|
TABLE 1 | DIMENSIONS AND WEIGHTS |
Issuing Committee
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This Committee is responsible for developing and maintaining standards for design, test, and procurement of fluid systems part standards to improve reliability and economy. Their primary focus is on AS standards development and support of military standards. The Committee also develops ISO standards in a Subcommittee Advisory Group (SCAG) to ISO/TC 20/SC 10, and SAE-MA derivatives thereof.
Structure: SAE G-3 -- Parent committee SAE G-3A -- Aerospace Couplings Subcommittee SAE G-3B -- Aerospace Fittings Subcommittee SAE G-3D -- Aerospace Hose Subcommittee SAE G-3E - Aerospace Tubing Assemblies Subcommittee U.S. SCAG to ISO/TC 20/SC 10 -- ISO standards Major projects: Support of Military Standards Reform Support of military standard conversions to MIL-PERF and MIL-DTL. Development of AS replacements for military standards designated for conversion. Establish document to list G-3 accepted replacements for replaced part standards and military back-up specifications. Development of PRI QML/QPL Development of Performance Review Institute (PRI) process for approval and surveillance of manufacturers (Qualified Manufacturer List, QML) and for approval of standard parts as qualified for use (Qualified Parts List, QPL). Development of ISO Standards, Imperial Units ISO/TC 20/SC 10 standards have typically been developed in SI units. The ISO has approved development of inch-based ISO standards to support commercial aviation. Basic design, test, and procurement specifications will be selected from military standards that are to be converted to Non-Government standard (NGS) and developed as ISO standards.Reference
Number | Title |
---|---|
AMS2750 | PYROMETRY |
AMS2770 | HEAT TREATMENT OF ALUMINUM AND ALUMINUM-BASE ALLOYS |
AMS4001 | ALUMINUM SHEET AND STRIP (2S-0) |
AMS5553 | NICKEL SHEET AND STRIP Low (0.02 max) Carbon Annealed |
AS4395 | FITTING END - FLARED TUBE CONNECTION, DESIGN STANDARD |
ASMEB46.1 | This document is not part of the subscrption. |
ASMEY14.36M | This document is not part of the subscrption. |
ASMEY14.5M | This document is not part of the subscrption. |
ASTMA240 | This document is not part of the subscrption. |
ASTMB152 | This document is not part of the subscrption. |
ASTMB162 | This document is not part of the subscrption. |
ASTMB451 | This document is not part of the subscrption. |
FED-QQ-A-1876 | This document is not part of the subscrption. |
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.