This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Application of Lda And Piv Techniques to the Validation of a Cfd Model of a Direct Injection Gasoline Engine
Annotation ability available
Sector:
Language:
English
Abstract
Two experimental techniques, Particle Image Velocimetry (PIV) using a water-analogy Dynamic Flow Visualisation Rig (DFVR) and Laser Doppler Anemometry (LDA) in a motored research engine, were used to investigate the flow pattern generated within the combustion chamber of a gasoline direct injection (G-DI) engine. The in-cylinder flow was also modelled for the two cases using the Computational Fluid Dynamics (CFD) code VECTIS; that is, models were created using first water and then air as the working fluid. The experimental and computational results were converted into the same format and hence compared qualitatively and quantitatively. All results showed good agreement and were used to validate the different techniques. The correlation between the CFD air simulation results and the LDA results demonstrates that the CFD code can be used to predict reliably the air motion created in the combustion chamber of a G-DI engine. The results from the CFD simulations using air and water showed the same general flow pattern within the induction stroke. The fact that the results from the DFVR also compared favourably with the CFD water and air models, indicates that these techniques can be used confidently in the development of the ports and combustion chamber of a G-DI engine.
Recommended Content
Authors
- S. M. Begg - University of Brighton
- L. S. Pommier - University of Brighton
- M. R. Heikal - University of Brighton
- M. A. Faure - Ricardo Consulting Engineers Ltd.
- M. Sadler - Ricardo Consulting Engineers Ltd.
- K. K. Oversby - Ricardo Consulting Engineers Ltd.
- J. Stokes - Ricardo Consulting Engineers Ltd.
Citation
Faure, M., Sadler, M., Oversby, K., Stokes, J. et al., "Application of Lda And Piv Techniques to the Validation of a Cfd Model of a Direct Injection Gasoline Engine," SAE Technical Paper 982705, 1998, https://doi.org/10.4271/982705.Also In
References
- Jackson N. S. Stokes J. Whitaker P. A. Lake T. H. “Stratified and Homogeneous Charge Operation for the Direct Injection Gasoline Engine - High Power with Low Fuel Consumption and Emissions” SAE 970543 1997
- Khalighi B. Haworth D. Huebler M. “Multidimensional Port-and-in-Cylinder Flow Calculations and Flow Visualization Study in an Internal Combustion Engine with Different Intake Configurations” SAE 94 187 1 1994
- Wren C. S. Johnson 0. “Gas Dynamics Simulation for the Design of Intake and Exhaust Systems - Latest Techniques” SAE 95 1367 1995
- Jackson N.S Stokes J. Heikal M.R. Downie J.H. “A Dynamic Flow Visualisation Rig for Automotive Combustion System Development’* SAE 950728 1995
- Faure M.A. H e i k a l M.R. J a c k s o n N.S. “PIV Measurements and Characterisation of In-Cylinder Flows in Combustion Engines” 8th International Symposium On Applications Of Laser Techniques To Fluid Mechanics Lisbon, Portugal 1996
- Glover A.R. Hundleby G.E. Hadded 0. ‘The Development of Scanning LDA for the Measurement of Turbulence in Engines” SAE 880378 1988
- Glover A.R. Hundleby G.E. H a d d e d 0. “An Investigation Into Turbulence in Engines Using Scanning LDA” SAE 880379 1988
- Hadded 0. Denbratt I. “Turbulence Characteristics of Tumbling Air Motion in Four-Valve S.I. Engines and Their Correlation with Combustion Parameters” SAE 9 10478 1991
- L a k e T.H. Stokes J. Whitaker P.A. Crump J.V. “Comparison Of Direct Injection Gasoline Combustion Systems” SAE 980154 1998
- Sadler M. Stokes. J. E d w a r d s S.P. Zhao H. Ladommatos N. “Optimisation of the Combustion System for a Direct Injection Gasoline Engine, Using a High Speed In-Cylinder Sampling Valve” Euro IV Challenge - Future Technologies & Systems IMechE 1997