This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Cooled EGR - A Key Technology for Future Efficient HD Diesels
ISSN: 0148-7191, e-ISSN: 2688-3627
Published February 23, 1998 by SAE International in United States
Annotation ability available
The paper reports on achievements obtained in an ongoing development program which is part of a european EUREKA joint research project named EFFLED (EFFicient Low Emission Diesel) being performed at AVL in cooperation with the companies DAF Trucks, Serck Heat Transfer, Robert Bosch and the Community of the City of Rotterdam. The main objective of this project is the development and refinement of a venturi supported exhaust gas recirculation (EGR) system for a turbocharged and intercooled heavy-duty (HD) diesel engine enabling map controlled cooled EGR rates which are high enough to achieve future low NOx emission standards at acceptable fuel consumption level. In addition to EGR, further technologies have been investigated, which may be required to meet future exhaust emission standards. As a result of these investigations it was found that for EURO 3 standards (NOx / PM = 5/0.1 g/kWh in the new european steady state cycle - ESC) cooled EGR alone leads to the required NOx reduction without worsening fuel consumption from EURO 2 levels. However, for meeting indicated EURO 4 standards (NOx / PM = 3/0.1 g/kWh in new european transient cycle - ETC), the use of a particulate trap will most probably be required with today's diesel fuel qualities in spite of only modest increase of soot due to EGR. Therefore, two different particulate filter systems as potential candidates have been tested, and their pros and cons compared.
INCREASINGLY STRINGENT exhaust emission regulations, which are expected to come into force around the turn of the century and thereafter worldwide in industrialized countries will require NOx and particulate emisson standards to be reduced by up to 60% from today's (1998) levels, see Fig. 1. To meet these future emission standards, the application of new technologies including exhaust gas aftertreatment systems will be indispensable, especially in view of maintaining or even improving the thermal efficiency of HD diesel engines.
Two different routes for meeting the future european standards are currently under discussion, Fig. 2. The application of SCR systems using urea-water solution as a NOx reducing agent (SCR = selective catalytic reduction) is assessed as the most effective NOx reduction technology in the long range /1,2,3,4/, with the benefit of allowing combustion to be optimized for best fuel efficiency and lowest particulates.
However, logistics for urea-water solution is a prerequisite, and on vehicles space for dosage system, urea tank, SCR catalyst and a modified exhaust muffler must be foreseen. Furthermore, durability and on-board-diagnostic (OBD) issues of the system need to be solved.
Alternatively, fig. 2 also suggests that cooled Exhaust Gas Recirculation (EGR) is offering a similar NOx reduction potential as does the SCR approach. Only moderate EGR rates would be necessary to meet EURO 3 standards with fuel consumption being equal to EURO 2 level and with minor effects on particulates /5,6,7/, whereas for EURO 4 at current status of development the use of a soot trap for reducing particulates seems to be a must due to the higher EGR rate requirements. In either case, a variety of potential problems have to be investigated and solved before EGR can be accepted in the heavy-duty diesel engine environment. More specific, major concerns are related to the durability of EGR components, EGR control requirements for transients, engine fouling (EGR cooler, intake ducts), and increased wear due to increased soot-in-oil and/or accelerated oil degradation.
In general, brake specific fuel consumption (BSFC) is of utmost importance to the truck user, and in the future it is expected to be improved continuously. Conducive measures, already in use today on a variety of engines, are the application of multi valve (3V & 4V) cylinder heads instead of two-valve heads, the use of fuel injection systems with increased fuel pressures in conjunction with reduced swirl levels, improved lube oil control, and the use of electronic engine management, especially for injection timing. Thus, fuel consumption for a given NOx level could be improved by up to 5 %. However, the magnitude of improvement depends also on the type of the test cycle.
The change of the european certification test cycle /8/ from the current 13-Mode ECE R49 to the new 13-Mode ACEA/OICA (or new european steady state cycle - ESC) for EURO 3 and finally to the FIGE transient test (or european transient cycle - ETC) for EURO 4, as shown in Fig. 3, makes the assessment of test cycle fuel consumption and emission results more complicated due to the different load/speed operating modes and weightings factors as well as due to transient effects.
The influence of the various test cycles on emissions and fuel consumption of a given EURO 2 engine is shown in Fig. 4. For NOx emissions being nearly at the same level (approx. 6.5 g/kWh) for all three test cycles, particulates and cycle fuel consumption decrease in the ESC due to the higher load factor and operation shifted to the mid speed range in this cycle, whereas in the ETC both fuel consumption and particulates increase, mainly as a result of transient operation.
In view of this background and the development directions discussed previously, a joint research project named EFFLED (EFFicient Low Emission Diesel, EUREKA No. 1593) was initiated by AVL List GmbH in cooperation with companies DAF Trucks N.V., Serck Heat Transfer, Robert Bosch GmbH, and the Community of the City of Rotterdam. The main objective of this project is the development and refinement of a venturi supported EGR system for a turbocharged and air/air intercooled HD diesel engine enabling map controlled cooled EGR with EGR rates high enough to achieve the NOx emission levels required beyond 2000 at competitive fuel consumption level. Since with current diesel fuel qualities particulates inevitably tend to increase with the required high EGR rates, also the use of particulate trap oxidizers is considered within the EFFLED project.
In the following sections, achievements of the still ongoing project are presented, with emphasis on both, the EGR system and its performance, and the behaviour of two different particulate trap systems being envisaged for future field operations of the engine, which finally is to be built into a DAF container vehicle and operated within the Community Vehicle Fleet of the City of Rotterdam.
CitationZelenka, P., Aufinger, H., Reczek, W., and Cartellieri, W., "Cooled EGR - A Key Technology for Future Efficient HD Diesels," SAE Technical Paper 980190, 1998, https://doi.org/10.4271/980190.
- Havenith, C., Verbeek, R. P., Heaton, D. M., van Sloten, P.: Development of a Urea DeNOx Catalyst Concept for European Ultra-Low Emission Heavy-Duty Diesel Engines, SAE Paper 952652
- Havenith, C., Verbeek, R. P.: Transient Performance of a Urea deNOx Catalyst System for Low Emissions Heavy-Duty Diesel Engines, SAE Paper 970185
- Fränkle, G. et al: Ein Abgasreinigungssystem für Nutzfahrzeuge SINOx (SINOx - The Exhaust Gas Purification System for Trucks), 18th International Vienna Motor Symposium, April 1997.
- Backes, R. et al: A Urea Lean NOx Catalyst System for Light Duty Diesel Vehicles, SAE Paper 952493
- Herzog, P. et al: NOx Reduction Strategies for DI Diesel Engines, SAE Paper 92 0470
- Hiereth, H. et al: Untersuchungen zur Kühlung und Rückführung des Abgases von Nutzfahrzeug-Motoren. Entwicklung eines Wärmeübertragers zur Kühlung des Abgases (Investigation of cooling and recirculating exhaust gases in heavy-duty truck engines. Development of exhaust gas cooler), 18th International Vienna Motor Symposium, April 1997.
- Havenith, C., Such, C.H., Porter, B.C., Nicol, A.J.: Erprobung eines Euro 3 Nutzfahrzeug-Dieselmotors mit Abgasrückführung (Demon-stration of a EURO 3 Heavy Duty Diesel Engine Using Exhaust Gas Recirculation), 18th International Vienna Motor Symposium, April 1997.
- Fränkle, G., Havenith, C. Chmela, F.: Test Cycle Development Euro 3 for Heavy Duty Diesel Engines, FISITA Congress Prague 1996, Paper
- Suzuki, T.: Development and Perspective of the Diesel Combustion System for Commercial Vehicles, IMechE, 1997 Prestige Lecture, 22 May 1997
- Bartsch, P.: Einsatz der Ladungswechselrech-nung in der Auslegung moderner 4-Takt-Motoren, Tagung “Ladungswechseloptimierung an 4-Takt-Motoren” (Application of gas exchange modelling in designing modern 4-stroke engines, Conference on Gas Exchange Optimization of 4-stroke Engines), Haus der Technik Essen, 6 November 1997
- Basara, B., Plimom, A., Bachler, G.: On the Simulation of Turbulent Flow and Heat Transfer in an Intake Manifold, Proceedings of 6th International Symposium on Flow Modeling and Turbulence Measurements, Tallahassee/Florida/USA, 8-10 Septtember 1996
- Alkidas, A.C.: Relationships between Smoke Measurements and Particulates Measurements, SAE Paper 840412
- N.N.: Cooeld EGR System to Reduce Emissions, High Speed Diesels & Drives, Nov./Dec. 1994
- Kugland, P., Ulmer, A., Zilmans, R.: Sauberer Diesel (Clean Diesel Engine), Verkehr und Technik, 12 (1989)
- Dursbeck, F., Heine, P., Voss, H.J., Waldeyer, H.: Konzept und Ergebnisse des Rußfilter Großversuchs (Design and Results of the Particulate Filter Large Scale Test), UBA No. 50 441/6 (M 1500), 1994, Berlin, Germany
- Heinrich, U.: Das kanzerogene Potential von Luftschadstoffen - Die Bedeutung von Kfz-Abgasen (The carcenogenic potential of air pollutants - Significance of vehicle exhaust), VDI-Berichte 952, Düsseldorf 1992, Germany
- Koch, K.: Zählen statt wiegen (Counting instead of weighing), Süddeutsche Zeitung No. 297/1996
- Lepperhoff, G., Lüders, H., Barthe, P., Lemaire, J.: Quasi-Continuous Particle Trap Regeneration by Cerium-Additives, SAE Paper 950369
- Mayer, A. et al: VERT - Clean Diesel Engines for Tunnel Construction, SAE Paper 970478
- Pattas, K., Samaras, Z. et al: Regeneration of DPF at Low Temperatures with the Use of a Cerium Based Fuel Additive, SAE Paper 960135
- Psaras, D. et al: Achieving the 2004 Heavy-Duty Diesel Emissions Using Electronic EGR and a Cerium Based Fuel Borne Catalyst, SAE Paper 970189
- Hawker, P. et al: Experience with a New Particulate Trap Technology in Europe, SAE Paper 970182
- Lemaire, J., Mustel, W., Zelenka, P.: Fuel Additive Supported Particulate Trap Regeneration Possibilities by Engine Management System Measures, SAE Paper 942069
- United States Patent No. 4.902.487
- Cooper, B., Thoss, J.: Role of NO in Diesel Particulate Emission Control, SAE Paper 890404
- Krüger, M., Lüders, H., Dürnholz, M.: Einfluß von Abgas-nachbehandlungsmaßnahmen auf die Eigenschaften der Partikel im Abgas von Fahrzeugdieselmotoren (Influence of Exhaust Gas Aftertreatment on Particulate Characteristics of Vehicle Diesel Engines), 6th Vehicle and Engine Engineering Conference, Oct. 1997, Aachen, Germany,
- Dementhon, J.-B., Martin, B.: Influence of Various Diesel Traps on Particulate Size Distribution, SAE Paper 972999
- Bertoli, C., Del Giacomo, N., Beatrice, C.: Diesel Combustion Improvements by the Use of Oxygenated Synthetic Fuels, SAE Paper 972972