This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Optimization of the Metallic Three-Way Catalyst Behavior
Annotation ability available
Sector:
Language:
English
Abstract
Manufacturers of automotive catalytic converters are constrained to design more effective and reliable systems to meet the stringent emission limits anticipated for the end of the decade. Reactor models and computer simulations may offer new possibilities for optimal catalytic converter design. For this reason, transient models have been developed using the commercial CFD (Computer Fluid Dynamics) code PHOENICS.
In this work the effects of catalyst design parameters are studied using the one-dimensional transient model for a single catalyst channel. The results indicate that the catalyst precious metal loading has a great influence on the catalyst light-off, and the geometric area (catalyst length and cell density) and the hydraulic radius (catalyst cell density) on the steady state conversion efficiency. The ceramic catalyst seems to have a higher tendency towards thermal shock than the metallic. The optimization of the metallic catalyst behavior inevitably leads to the use of a high cell density to obtain the best steady state behavior. The precious metal loading needed to reach fast light-off can be optimized by shortening the substrate length.
The behavior of the advanced metallic catalyst is compared with the 400 cpsi ceramic catalyst using the three-dimensional transient model. This simulates the fluid dynamics, chemical kinetics and heat and mass transfer taking place in a catalyst and its assembly. The volume of the metallic catalyst is a half of that of the ceramic. The geometric areas of the catalysts are almost identical. Both catalysts contain the same amount of precious metals. The length of the ceramic honeycomb is double compared to that of the metallic. Due to the smaller heat capacity, better heat conduction and heat transfer the 800 cpsi metallic catalyst heats up faster than the 400 cpsi ceramic one. Furthermore, the better mass transfer characteristics of the metallic catalyst enable an almost 4.5 % higher conversion efficiency than the ceramic.
Recommended Content
Authors
Topic
Citation
Luoma, M., Härkönen, M., Lylykangas, R., and Sohlo, J., "Optimization of the Metallic Three-Way Catalyst Behavior," SAE Technical Paper 971026, 1997, https://doi.org/10.4271/971026.Also In
References
- Luoma, M. Lappi, P. Lylykangas, R. Evaluation of high cell density Z-flow catalyst Warrendale 1993 SAE Technical Paper Series 930940 187 198
- Luoma, M. Modeling of exhaust gas catalytic converters Oulu 1996 University of Oulu, Dep. of Process Engineering 94
- Mannila, P. Salmi, T. et al. Stationary kinetics of essential reactions on automobile exhaust Pt-RH/AI 2 O 3 catalyst Appl. Catalysis, B: Environmental 7 1996 179 198
- Ahola, J. Transient kinetics of automobile exhaust catalyst Oulu 1993 University of Oulu, Dep. of Process Engineering 83
- Oh, S.H. Cavendish, J.C. Transients of monolithic catalytic converters. Response to step changes in feed-stream temperature as related to controlling automobile emissions. Ind.Eng.Chem.Prod.Res.Dev. 21 1982 1 29 37
- Voltz, S. Morgan, C.R. et al. Kinetic study of carbon monoxide and propylene oxidation on platinum catalysts Ind.Eng.Chem.Prod.Res.Dev. 12 1973 4 294 301
- Luoma, M. Smith, A.G. The use of Phoenics in the design of catalytic converters The Phoenics Journal 9 1996 76 100
- Clarkson, R.J. Benjamin, S.F. et al. An integrated computational model for the optimization of monolith catalytic converters Warrendale 1993 SAE Technical Paper Series 931071 11 24
- Fueyo, N. 1-D simulation of a catalytic converter for car Phoenics Demonstration Report PDR/CFDU/IC/35 CHAM Ltd. London 1987 30
- Will, N.S. Bennett, C.J. Flow maldistributions in automotive converter canister and their effect on emission control. Warrendale 1992 SAE Technical Paper Series 922339 183 210
- Kays, W.M. Convective Heat and Mass Transfer New Delhi 1979 Tata McGraw-Hill Publishing Company Ltd. 387
- Shah, R.K. London, A.L. Laminar flow forced convection in ducts Irvine, T.F. Harnett, J.P Advances in heat transfer Supplement I New York 1978 Academic Press 476
- Day, J.P. Thompson, D.F. a comparison of ceramic and metallic automotive supports Mater.Sci.Monogr., Ceramics Today - Tomorrow's Ceramics 1991 66D 2531 2540
- Socha, L.S. Jr. Day, J.P. Barnett, E.H. Impact of catalyst support design parameters on FTP emissions Warrendale 1989 SAE Technical Paper Series 892041 9
- Taylor, K.C. Automobile catalytic converters New York 1984 54
- Ryan, M.J. Becker, E.R. Zygourakis, K. Light-off performance of catalytic converters: The effect of heat/mass transfer characteristics Warrendale 1991 SAE Technical Paper Series 910610 12
- Cundari, D. Nuti, M. A one-dimensional model for monolithic converter: Numerical simulation and experimental verification of conversion and thermal responses for two-stroke engine Warrendale 1991 SAE Technical Paper Series 910668 45 52
- Day, J.P. Socha, L.S. Jr. The design of automotive catalyst supports for improved pressure drop and conversion efficiency Warrendale 1991 SAE Technical Paper Series 910371 10
- Brück, R. Diewald, R. et al. Design criteria for metallic substrates for catalytic converters Warrendale 1995 SAE Technical Paper Series 950789 11
- Jasper, T.S. Robinson, K. et al. Monolilth substrate effects on catalyst light-off Crucq A. Catalysis and automotive pollution control II Amsterdam 1991 Elsevier Science Publishers B.V. 523 535
- Oh, S.H. Catalytic converter modeling for automotive emission control Chem. Ind. (Dekker) 51 1993 259 295
- Psyllos, A. Philipopoulos, C. Performance of a monolithic catalytic converter used in automotive emission control: The effect of a longitudinal parabolic active metal distribution Ind.Eng.Chem.Res. 32 1993
- Bressler, H. Weltens, H. Terres, F. Multiple disc catalytic converters - an innovative approach for improved conversion at lower cost Warrendale 1994 SAE Technical Paper Series 940936 317 329
- Andersson, S.L. Schöön, N.-H. Methods to increase the efficiency of a metallic monolithic catalyst Ind.Eng.Chem.Res. 32 1993 1081 1086