This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Knock Erosion in Spark-Ignition Engines
Annotation ability available
Sector:
Language:
English
Abstract
The traditional philosophy that all knocking combustion is damaging has caused engine and fuel manufactures to operated with large “safety” margins, incurring both fuel production and consumption costs.
This paper describes an attempt to relate knocking conditions to erosion damage. One of the goals was to discover a measurable knock intensity parameter which describes the propensity of knock to cause erosion damage.
An experimental technique was developed in which test specimens were subjected to controlled knocking conditions in the combustion chamber of a modified engine. A photographic method was employed to measure the relative level of erosion on the test specimens. This methodology was used to determine the effect of fuel type and operating conditions on knock-induced erosion. It was confirmed that the geometry as well as the temperature played a considerable role in the damage mechanism.
The data from these tests showed no correlation between the classical knock intensity criteria (i.e.: peak-to-peak pressure amplitude) and the measured erosion damage. This result was understood as an indication that the classical knock intensities are a measure of the global aftermath of knocking combustion, which is not directly related to the local condition in the end-gas crevices during the auto-ignition-detonation process.
This was confirmed by a stress calculation applied to bent specimens, which revealed the existence of local pressure differences of greater than 350 bar. This is many times greater than that recorded by the pressure transducers.
The erosion test results showed that the cylinder pressure at the point of auto-ignition was correlated to the measured erosion damage. It was concluded that the strength of the developing-detonation process in the crevice region was strongly related to the initial conditions in the end-gas prior to auto-ignition.
Microscopy revealed that knock damage is accompanied by the development and propagation of micro-cracks within the erosion zones.
This work now provides a means of measuring the knock-erosion potential and not simply the knock intensity.
Recommended Content
Authors
Citation
Fitton, J. and Nates, R., "Knock Erosion in Spark-Ignition Engines," SAE Technical Paper 962102, 1996, https://doi.org/10.4271/962102.Also In
References
- Clark, D. Trans. Faraday Soc. 22 338 1926
- Litzinger, T.A. “A review of experimental studies of knock chemistry in engines” Proc. Energy Comb. Sci. 16 1990
- König, G. et al “Role of Exothermic Centres on Knock Initiation and Knock Damage” SAE Paper No. 902136 1990
- Maly, R.R. Klein, R. Peters, N. König, G. “Theoretical and Experimental Investigation of Knock Induced Surface Destruction” SAE Paper No. 900025 1990
- Yates, A. Dutkiewicz, R.K. “Petrol octane requirements for South Africa” Report No.GEN 123 Energy Research Institute University of Cape Town January 1988
- Taylor, C.F. “The Internal Combustion Engine in Theory and Practice, Vol.2” The MIT Press Massachusetts 1980
- French, C.C. Atkins, K.A. “Thermal Loading of A Petrol Engine” Proc. Of IMechE 187 49/73 1973
- Betts, W.E. “Avoiding high speed knock engine failures” Int. Symp. on Knocking Combustion Engines Wolfsburg Nov 1981
- Betz, G. Ellerman, J. “Knock-related piston damage in gasoline engines, knock measurement technique, aspects of knock failure” Int. Symp. on Knocking Combustion Engines Wolfsburg Nov 1981
- Essig, G. “Piston loading at knocking combustion (detonation)” Int. Symp. on Knocking Combustion Engines Wolfsburg Nov 1981
- Lee, W. Schaefer, H.J. “Analysis of Local Pressures, Surface Temperatures and Engine Damages under Knocking Conditions” SAE Paper 830508 1983
- Spicher, U. Kroger, H. Ganser, J. “Detection of Knocking Combustion Using Simultaneous High Speed Schlieren Cinematography and Multi Optical Fibre Technique” SAE Paper 912312 1991
- Evans, P.G. “A Fast Data-Acquisition System for Investigating Combustion Phenomena in Spark-Ignition Engines” SAE Paper 840057 1984
- Pischenger, R. Krassig, G. Glaser, J. “Methods for the Evaluation of Quartz Pressure Transducers” Technische Universitat Graz Austria ISATA 85043
- Nates, R.J. Yates, A.D.B. “Knock Damage Mechanisms in Spark-Ignition Engines” SAE Paper No. 942064 1994
- Fitton, J.C. “Knock-Erosion Damage in Spark-Ignition Engines” MSc Thesis University of Cape Town December 1995
- Nates, R.J. “Knock Damage in Spark-Ignition Engines” Phd Dissertation University of Cape Town December 1995
- Pan, J Sheppard, G. “A Theoretical and experimental study of the modes of end-gas auto-ignition leading to knock in SI engines” SAE Paper No. 942060 1994
- Klein, R. Breitbach, H. Geratz, K.J. Senger, W. “Surface Erosion by High Speed Combustion Waves” Proc. 25th Int. Symp. on Combustion California August 1994