This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experimental Studies Aimed at Lowering the Electrical Energy Requirements of a Plasma Jet Ignition System for M100 Fuelled Engines
Annotation ability available
Sector:
Language:
English
Abstract
This paper describes experimental studies carried out as part of a program to develop a neat methanol (M100) version of a GM 4-cylinder light truck engine. The engine was originally intended for variable fuel applications with fuels containing up to 80% ethanol. To permit M100 operation, a variable energy ignition circuit and special recessed surface gap ignitors have replaced the standard ignition components. This is referred to as a “plasma jet” ignition system, and is employed both to overcome the cold starting difficulties inherent with neat alcohol fuel and to permit less enrichment to be used during start-up in the interest of reduced hydrocarbon emissions.
The plasma jet ignition systems used in previous related studies suffered from excessively high ignition energy requirements which would be detrimental to ignitor durability. Thus efforts were carried out to optimize the circuit and ignitors with the aim of limiting ignition energy to conventional levels during warm running, while permitting intermittent duty operation during cold starting at approximately ten times the warm running energy level. These studies included both bench tests to determine electrical energy transfer to the spark gap through high speed voltage and current measurements, and engine tests examining cyclic variation and heat release characteristics derived from cylinder pressure measurements. As a result of this work, it was shown that improvements in warm idle combustion characteristics could be achieved with the complete plasma jet system at energy levels below that of the standard ignition system. Use of the plasma jet ignition circuit in combination with conventional spark plugs did not result in similar improvements.
Authors
Topic
Citation
Gardiner, D., Mallory, R., Pucher, G., Todesco, M. et al., "Experimental Studies Aimed at Lowering the Electrical Energy Requirements of a Plasma Jet Ignition System for M100 Fuelled Engines," SAE Technical Paper 961989, 1996, https://doi.org/10.4271/961989.Also In
References
- Hellman, K.H. Environmental Protection Agency, Motor Vehicle Emission Laboratory
- Gardiner, D.P Bardon, M.F Rao, VK. Battista, V “Review of the Cold Starting Performance of Methanol and High Methanol Blends in Spark Ignition Engines Neat Methanol” SAE Paper # 902154 Society of Automotive Engineers Warrendale, PA 1990
- Zelenko, P. Kapus, P Mikulic, L.A. “Development and Optimization of Methanol Fueled Compression Ignition Engines for Passenger Cars and Light Duty Trucks “SAE Paper # 910851 Society of Automotive Engineers Warrendale, PA 1991
- Bretsch, R.I Hellman, K H “Evaluation of a Passenger Car Equipped with a Direct Injection Neat Methanol Engine” SAE Paper # 920196 Society of Automotive Engineers Warrendale, PA 1992
- Last, R.J “Development Status for Two Dedicated Methanol Engine Combustion Technologies DI Hot Surface Ignition and DI Spark Ignited Stratified Charge,” 1993 Windsor Workshop on Alternative Fuels June 14-16 Toronto 1993
- Pike, M S Guglielmello, T.J Hodgson, J W “Development of a Cold-Start Device for Methanol-Fueled Engines” SAE Paper # 932772 Society of Automotive Engineers Warrendale, PA 1993
- Nishimura, J Hosoyai, D Ito, T Iwai, N Akai, M. “Study of Partial Oxidation Combustor Using Ultrasonic Atomizer to Improve Cold Startability of Methanol Engine” SAE Paper # 940767 Society of Automotive Engineers Warrendale, PA 1994
- Dippo, J Karpuk, M. Cowley, S “Design of a Methanol Dehydration Reactor for Cold Starting Methanol-Fueled Engine” Proc of the IX International Symposium on Alcohol Fuels 580 585 Nov 12-15 1991
- Gardiner, D.P Rao, V.K. Bardon, M.F. Dale, J D Smy, P.R Haley, R.F “Improving the Operation of Gasoline and Methanol Fuelled Spark Ignition Engines Under Canadian Winter Conditions” SAE Paper # 920011 Society of Automotive Engineers Warrendale, PA 1992
- Gardiner, D.P Rao, V.K. Bardon, M.F Dale, J D Smy, P.R Haley, R.F Dawe, J.R Battista, V “Sub-Zero Cold Starting of a Port-Injected M100 Engine Using Plasma Jet Ignition and Prompt EGR” SAE Paper # 930331 Society of Automotive Engineers Warrendale, PA 1993
- Dawe, J.R Smy, P.R Haley, R.F Dale, J.D Bardon, M.F Gardiner, D.P “Plasma Jet Ignition of Methanol at Subzero Temperature” Proc Instn Mech Engrs 208 J Automobile Engineering 1994
- Gardiner, D.P Mallory, R W Rao, V.K. Bardon, M.F Battista, V “Vehicle Implementation and Cold Start Calibration of a Port Injected M100 Engine Using Plasma Jet Ignition and Prompt EGR” SAE Paper # 952375 Society of Automotive Engineers, Warrendale, PA. 1995
- Topham, D.R Smy, P.R Clements, R M “An Investigation of a Coaxial Spark Ignitor with Emphasis on its Practical Use” Combustion and Flame 25 187 1975
- Asik, J.R. Piatkowski, P Foucher, M.J Rado, W G. “Design of a Plasma Jet Ignition System for Automotive Application” SAE Paper # 770355 Society of Automotive Engineers Warrendale, PA 1977
- Edwards, C.F. Oppenheim, A.K. Dale, J.D “A Comparative Study of Plasma Jet Ignition Systems” SAE Paper # 830479 Society of Automotive Engineers Warrendale, PA 1983
- Dale, J D Wilson, J.P Santiago, J Smy, P. Clements, R. “Low Temperature Starting of Diesel Engines Using Timed Spark Discharge” SAE Paper # 850049 Society of Automotive Engineers Warrendale, PA 1985
- Cavolowsky, J.A. Paris, D W Oppenheim, A.K. Smy, P.R “Formation of a Plasma Puff” SAE Paper # 870609 Society of Automotive Engineers Warrendale, PA 1987
- Murase, E Ono, S Hanada, K. Nakahara, S. “Plasma Jet Ignition in Turbulent Lean Mixtures” SAE Paper # 890155 Society of Automotive Engineers Warrendale, PA 1989
- Anderson, R. Asik, J “Lean Air Fuel Ignition System Comparison in a Fast Burn Engine” SAE Paper # 850076 Society of Automotive Engineers Warrendale, PA 1985
- Teets, R.E Sell, J.A. “Calorimetry of Ignition Sparks” SAE Paper # 880204 Society of Automotive Engineers Warrendale, PA 1988
- VanDuyne, E. Porreca, P “Performance Improvement from Dual Energy Ignition on a Methanol Injected Cosworth Engine” SAE Paper # 940150 Society of Automotive Engineers Warrendale, PA 1994
- Anderson, H.E. “Low Impedance Capacitor Discharge System and Method” Jan. 29 1974
- Hamley, J.P “High Energy Spark Ignition System” Sep 23 1980
- Imai, I. Yulatsuga, H. “Plasma Jet Ignition System” Dec 29 1981
- Iman, I Some, M. “Plasma Jet Ignition System with Noise Suppressing Arrangement” May 4 1982
- Jorgensen, A.A. “Ignition System with Power Boosting Arrangement” Aug 24 1982
- Ezoe, M “Plasma Jet Ignition System for Internal Combustion Engine” Jan 24 1983
- Anzai M. “Plasma Jet Ignition System” Jan 25 1983
- VanDuyne, E. Porreca, P “Dual Energy Ignition System” 1993
- Treager, I.E. Aircraft Gas Turbine Engine Technology McGraw-Hill New York 1970
- Anderson, R.W “The Effect of Ignition System Power on Fast Burn Engine Combustion” SAE Paper # 870549 Society of Automotive Engineers Warrendale, PA 1987
- Anderson, R.W Asik, J.R. “Plasma Jet Ignition System” Dec 11 1984
- Pischinger, S Heywood, J B “A Study of Flame Development and Engine Performance with Breakdown Ignition Systems in a Visualization Engine” SAE Paper # 880518 Society of Automotive Engineers Warrendale, PA 1988
- Pischinger, S “Effects of Spark Plug Design Parameters on Ignition and Flame Development in an SI-Engine” Massachusetts Institute of Technology January 1984
- Ziegler, G.FW Wagner, E.P Suggau, B Maly, R Herden, W. “Influence of a Breakdown Ignition System on Performance and Emission Characteristics” SAE Paper # 840992 Society of Automotive Engineers Warrendale, PA 1984
- Smy, P.R Clements, R.M. Dale, J.D Simeoni, D. Topham, D.R. “Efficiency and Erosion Characteristics of Plasma Jet Ignitors” J Phys. D Appl, Phys. 16 783 1983
- Smy, P.R Clements, R.M Topham, D.R “Efficiency and Erosion of Plasma Jet Ignitors - Variation with Voltage” Combustion Science and Technology 42 317 1980
- Jiewertz, S Klemisch, B Anderlind, T Gillbrand, P S “Saab Direct Ignition System and Its Cold Start Performance” SAE Paper # 890044 Society of Automotive Engineers Warrendale, PA 1984
- Herweg, R. Maly, R.R “A Fundamental Model for Flame Kernel Formation in S.I Engines” SAE Paper # 922243 Society of Automotive Engineers Warrendale, PA 1992
- Kupe, J Wilhelmi, H. Adams, W “Operational Characteristics of a Lean Burn SI-Engine Comparison Between Plasma-Jet and Conventional Ignition System” SAE Paper # 870608 Society of Automotive Engineers Warrendale, PA 1987
- Ward, M.A.V “A New Spark Ignition System for Lean Mixtures Based on a New Approach to Spark Ignition” SAE Paper # 890475 Society of Automotive Engineers Warrendale, PA 1989
- Brunt, M.F.J Emtage, A.L “Evaluation of IMEP Routines and Analysis Errors” SAE Paper # 960609 Society of Automotive Engineers Warrendale, PA 1996
- Neame, G.R Gardiner, D.P Mallory, R W Rao, V.K. Bardon, M.F Battista, V “Improving the Fuel Economy of Stoichiometrically Fuelled S.I. Engines by Means of EGR and Enhanced Ignition - A Comparison of Gasoline, Methanol and Natural Gas” SAE Paper #952365 Society of Automotive Engineers Warrendale, PA 1995
- Quader, A.A. “What Limits Lean Operation in Spark Ignition Engines - Flame Initiation or Propagation?” SAE Paper #7600760 Society of Automotive Engineers Warrendale, PA 1976
- Kuroda, H. Nakajima, K. Sugihara, Y Muranuka, S “The Fast Burn With Heavy EGR, New Approach for Low NOx and Improved Fuel Economy” SAE Paper # 780006 Society of Automotive Engineers Warrendale, PA 1978
- Modien, R Dale, J “The Effect of Enhanced Ignition Systems on Early Flame Development in Quiescent and Turbulent Conditions” SAE Paper # 910564 Society of Automotive Engineers Warrendale, PA 1991