This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Prediction of Preignition Reactivity for n-Butane and iso-Butane Blends Using a Reduced Chemical Kinetic Model
Annotation ability available
Sector:
Language:
English
Abstract
Recently, we reported the development of a new reduced chemical kinetic model for predicting reactivity and autoignition behavior of primary reference fuels in a motored research engine. The predicted oxidation behavior (ignition delay, preignition heat release, and evolution of key chemical species) is in fairly good agreement with experiments. In addition, the model reproduced the experimentally observed dependence of overall reactivity on charge density and manifold inlet conditions. This paper reports our initial effort to apply this new reduced chemical kinetic model to other fuels. Specifically, the model was tested using neat n-butane and n-butane/iso-butane blends (10, 20, and 48 percent by volume iso-butane) under skip fired conditions. The only adjustments made in the model were to the fuel specific rate parameters of the RO2· isomerization reaction, the reaction of aldehydes with OH·, and the reaction forming cyclic ethers. The ignition delay, heat release, fuel consumption and CO formation in the end gas were calculated using this model and were compared with predictions using the Hu and Keck reduced chemical kinetic model. Results showed that with adjustment of fuel specific rate parameters our model can predict the magnitude of cumulative heat release quite well with a 20 CAD discrepancy in the timing. The model can also generally predict the fuel consumption and CO formation, with the characteristic shapes of the profiles varying as the percentage of iso-butane increases in the blend. This demonstrates that the model has the potential to be applicable for a broader range of fuels.
Recommended Content
| Technical Paper | Emission of CO2 and Fuel Consumption for Automotive Vehicles |
| Technical Paper | Series Turbocharging for the Caterpillar ® Heavy-Duty On-Highway Truck Engines with ACERT™ Technology |
Authors
Topic
Citation
Wang, S., Miller, D., and Cernansky, N., "Prediction of Preignition Reactivity for n-Butane and iso-Butane Blends Using a Reduced Chemical Kinetic Model," SAE Technical Paper 961154, 1996, https://doi.org/10.4271/961154.Also In
References
- Cernansky, N.P. Green, R.M. Pitz, W.J. Westbrook, C.K. “Chemistry of Fuel Oxidation Preceding End-Gas Autoignition” Comb . Sci . Technol . 50 3 25 1986
- Green, R.M. Cernansky, N.P. Pitz, W.J. Westbrook, C.K. “The Role of Low Temperature Chemistry in the Autoignition of n-Butane” SAE Paper No. 872108 SAE Trans . 96 1987
- Henig, Y. Addagarla, S. Miller, D.L Wilk, R.D. Cernansky, N.P. “Autoignition of n-Butane/Isobutane Blends in a Knock Research Engine” SAE Paper No. 890157 SAE Trans . 98 1989
- Kalghatgi, G.T. Snowdon, N. McDonald, C.R. “Studies of Knock in a Spark Ignition Engine with ‘CARS’ Temperature Measurements and Using Different Fuels” SAE Paper No. 950690 1995
- Stiebels, B. Schreiber, M. Sakat Sadat, A. “Development of a New Measurement Technique for the Investigation of End-Gas Autoignition and Engine Knock” SAE Paper No. 960827 1996
- Pitz, W.J. Westbrook, C.K. “Chemical Kinetics of the High Pressure Oxidation of n-Butane and Its Relation to Engine Knock” Combust. and Flame 63 113 1986
- Halstead, M.P. Kirsch, L.J. Prothero, A. Quinn, C.P. 1975 “A Mathematical Model for Hydrocarbon Autoignition at High Pressure” Proc. Roy . Soc. A346 515 1975
- Cox, R.A. Cole, J.A. “Chemical Aspects of the Autoignition of Hydrocarbon/Mixtures” Combust . and Flame 60 109 1985
- Hu, H. Keck, J. “Autoignition of Adiabatically Compressed Combustible Gas Mixtures” SAE Paper No. 872110 SAE Trans . 96 1987
- Cowart, J.S. Keck, J.C. Heywood, J.B. Westbrook, C.K. Pitz, W.J. “Engine Knock Predictions Using a Fully-Detailed and a Reduced Chemical Kinetic Mechanism” Twenty-Third Symposium (Int'l) on Combustion 1055 1990
- Mueller, U.C. Peters, N. Linan, A. “Global Kinetics For n-Heptane Ignition at High Pressure” Twenty-Fourth Symposium (Int'l) on Combustion 777 1992
- Li, H. Miller, D.L. Cernansky, N.P. “Development of a Reduced Chemical Kinetic Model For Prediction of Preignition Reactivity and Autoignition of Primary Reference Fuels” SAE Paper No. 960498 1996
- Addagarla, S. Henig, Y. Wilk, R.D. Miller, D.L. Cernansky, N.P. “Effect of Fuel-Air Mixture Stressing on Preignition Heat Release in a Knock Research Engine” SAE Paper No. 892082 SAE Trans. 98 1989
- Ferguson, C.R. Green, R.M. Lucht, R.P. “Unburned Gas Temperature in an Internal Combustion Engine. II: Heat Release Computations” Comb. Sci. and Technol. 55 63 1987
- Li, H. Miller, D.L. Cernansky, N.P. “A Study on the Application of a Reduced Chemical Reaction Prediction” SAE Paper No. 922328 SAE Trans . Section 5 1992
- Li, H. Prabhu, S.K. Miller, D.L. Cernansky, N.P. “Autoignition Chemistry Studies on Primary Reference Fuels in a Motored Engine” SAE Paper No. 942062 SAE Trans. 1994
- Pitz, W.J. Lawrence Livermore National Laboratory Livermore, CA February 1996
- Wilk, R.D. Pitz, W.J. Westbrook, C.K. Addagarla, S. Miller, D.L. Cernansky, N.P. Green, R.M. “Combustion of n-Butane and iso-Butane in an Internal Combustion Engine: A Comparison of Experimental and Modeling Results” Twenty-Third Symposium (Int'l) on Combustion 1047 1990