This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Pressure Modulated Injection and Its Effect on Combustion and Emissions of a HD Diesel Engine
Annotation ability available
Sector:
Language:
English
Abstract
The paper describes the concept selection, design and performance of a fuel injection equipment (FIE) which provides high flexibility in shaping the injection rate. With this injection system standard and boot shaped injection rates as well as pilot injections and post injections can be achieved throughout the hole speed and load range. Special emphasis was drawn to realize boot rate shaping by pressure modulation rather than by throttling the fuel flow (i.e.: the system is operated with fully opened needle during the whole injection period and no throttling device limits the fuel flow in front of the nozzle to reduce the injection rate).
Initial engine tests on a single cylinder research engine with 2 liter displacement were carried out at one operating point (1000 rpm, 200 mm3/str = 75% of full load fueling). Boot and pilot (split) injection rate shaping strategies are compared to a standard injection without rate shaping. At constant smoke and BSFC the boot injection shows a considerable improvement potential in NOx emissions of up to -14%, or NOx and BSFC can be reduced simultaneously by -9% and -7 respectively. The results with pilot injection are less promising than the results with boot injection. Furthermore, they are sensitive to pilot timing and to injection pressure as well as fueling during pilot injection.
Recommended Content
Authors
Citation
Erlach, H., Chmela, F., Cartellieri, W., and Herzog, P., "Pressure Modulated Injection and Its Effect on Combustion and Emissions of a HD Diesel Engine," SAE Technical Paper 952059, 1995, https://doi.org/10.4271/952059.Also In
Diesel Engine Combustion and Emissions From Fuel to Exhaust Aftertreatment
Number: SP-1113; Published: 1995-09-01
Number: SP-1113; Published: 1995-09-01
References
- Herzog, P. “The Ideal Rate of Injection for Swirl Supported HSDI Diesel Engines” IMECHE Conference Birmingham 1989
- Herzog, P. 1989
- Erlach, H. Herzog P. Jihlava Tschechoslowakia Oct. 1991
- Herzog. P. Bürgler, L. Winklhofer, E. Zelenka, P. Cartellieri, W. “NOx Reduction Strategies for DI Diesel Engines” SAE-Paper 920470
- Athenstaedt, G. Herzog, P. Noraberg, J. Ruhri, F. 1988
- Needham, J. R. May, M. P. Doyle, D. M. Faulkner, S.A. Ishiwata, H. “Injection Timing and Rate Control - A Solution for Low Emissions” SAE-Paper 900854
- Klein, H. Frankfurt 1992
- Augustin, U. 1990
- Wojik, K. Herzog, P. 1990
- Priesner, H. 1990
- Bech. N. H. Chen, S.K. “Injection Rate Shaping and High Speed Combustion Analysis - New Tools for Diesel Engine Combustion Development” SAE- Paper 900639
- Omori, T. “New Electronically Controlled Fuel Injection System ECD-U2 for Clean Diesel Engines” AVL Tagung Motor und Umwelt 1992
- Lauvin. P. Löffler, A. Schmitt, A. Zimmermann, W. Fuchs, W. “Electronically Controlled High Pressure Unit Injector System for Diesel Engines” SAE Paper 911819
- Gill, A. P. “Design Choices for 1990's Low Emission Diesel Engines” SAE-Paper 880350
- Ofner, H. Gill, D.W. “A General Purpose Simulation Model for High Pressure Fuel Injection and Other Mechanical-Hydraulic Systems” IMECHE Cambridge 1991
- Dekena, M. Erlach, H. 1990
- Bosch, W. 1964
- Chmela, F.G. Werlberger, P. Cartellieri, W.P. “Parameters Affecting In-Cylinder Soot and NOx Formation in a Direct Injection Diesel Engine” XXIV FISITA Congress London 1992
- Pierpont. D. A. Montgomery, D. I. Reitz, R. D. “Reducing Particulate and NOx Using Multiple Injections and EGR in a D.I. Diesel” SAE-Paper 950217
- Nehmer, D. A. Reitz, R.D. “Measurement of the Effect of Injection Rate and Split Injections on Diesel Engine Soot and NOx-Emissions” SAE-Paper 940668
- Klein, H. Rulfs, H. 1992
- Bürgler L. Herzog, P. Zelenka, P. “Strategies to meet US 1994/95 diesel engine federal emission legislation for HSDI diesel engine powered vehicles” Proc. Inst. Mech. Engrs. 206 1991
- Zelenka, P. Kriegler, W. Herzog, P. Cartellieri, W. “Ways Toward the Clean Heavy Duty Diesel” SAE Paper 900602
- Aoyama, T. Mizuta, J. Oshima, Y. “NOx Reduction by Injection Control” SAE-Paper 900637
- Decker, R. Huber, G. Schmöller, R. Frankfurt 1989
- Cartellieri, W. Herzog, P. “Swirl Supported or Quiescent Combustion for 1990's Heavy Duty DI Diesel Engines - An Analysis” SAE-Paper 880342
- Bürgler, L. Herzog. P Winklhofer, E. “The Influence of Injection System Parameters on DI-Diesel Spray Structure, Spray Ignition and Combustion” IMECHE Birmingham 1992