This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Diesel Fuel Lubricity
Annotation ability available
Sector:
Language:
English
Abstract
The United States and Europe are mandating increasingly severe diesel fuel specifications, particularly with respect to sulfur content, and in some areas, aromatics content. This trend is directed towards reducing vehicle exhaust emissions and is generally beneficial to fuel quality, ignition ratings, and stability. However, laboratory studies, as well as recent field experience in Sweden and the United States, indicate a possible reduction in the ability of fuels to lubricate sliding components within the fuel injection system. These factors, combined with the trend toward increasing injection pressure in modern engine design, are likely to result in reduced durability and failure of the equipment to meet long-term emissions compliance. The U.S. Army Belvoir Fuels and Lubricants Research Facility (BFLRF) located at Southwest Research Institute (SwRI) developed an accelerated wear test that predicts the effects of fuel lubricity on injection system durability. This test now has been widely used by fuel, additive, and equipment manufacturers. Several thousand fuel samples have been evaluated to date, and collectively, they form one of the largest databases on fuel lubricity currently in existence. This range of data permits a good overview of the commercially available fuels and confirms a general decrease in fuel lubricity due to increased refining severity. The results indicate that no high-sulfur fuel (>0.15 mass%) had poor lubricity, while a number of low-sulfur fuels (<0.05 mass%) did produce unacceptable wear. The lubricity of many highly refined fuels is probably being restored using relatively high concentrations of additive.
Recommended Content
Technical Paper | Fuel Lubricity Reviewed |
Technical Paper | Fuel Lubricity: Statistical Analysis of Literature Data |
Technical Paper | Lubricity of Low Sulfur Diesel Fuels |
Authors
Citation
Lacey, P. and Westbrook, S., "Diesel Fuel Lubricity," SAE Technical Paper 950248, 1995, https://doi.org/10.4271/950248.Also In
References
- Springer, K.J. “Low Emission Diesel Fuel for 1991-1994,” Advances in Engines Emissions Control Technology ICE 5 ASME 1989
- ASTM Designation: D 975-81 “Standard Specification for Diesel Fuel Oils,” ASTM 1916 Race Street, Philadelphia, PA 1981
- Ullman, T.L. “Investigation of the Effects of Fuel Composition and Injection Combustion System Type on Heavy-Duty Diesel Exhaust Emissions,” Southwest Research Institute Report Coordinating Research Council, Inc. March 1989
- Ullman, T.L. “Investigation of the Effects of Fuel Composition on Heavy-Duty Diesel Engine Emissions,” SAE Technical Paper No. 892072 September 1989
- Ullman, T.L. Mason, R.L. Montalvo, D.A. “Study of Fuel Cetane Number and Aromatic Content Effects on Regulated Emissions from a Heavy-Duty Diesel Engine,” Southwest Research Institute Report Coordinating Research Council, Inc. September 1990
- Ullman, T.L. Mason, R.L. Montalvo, D.A. “Effects of Fuel Aromatics, Cetane Number, and Cetane Improver on Emissions From a 1991 Prototype Heavy-Duty Diesel Engine,” SAE Technical Paper No. 902171 October 22-25 1990
- Nikanjam, M. “Development of the First CARB-Certified California Alternative Diesel Fuel,” SAE Technical Paper No. 930728 SAE International Congress and Exposition Detroit, MI March 1-5 1993
- Galiano-Roth, A.S. Page, N.M. “Effect of Hydroprocessing on Lubricant Base Stock Composition and Product Performance,” Lubrication Engineering 50 8 659 654
- Lacey, P.I. “Wear With Low Lubricity Fuels, Part I: Development of a Wear Mapping Technique,” Wear 160 1993 325 332
- Lacey, P.I. “Wear With Low Lubricity Fuels, Part II: Correlation Between Wear Maps and Pump Components,” Wear 160 1993 333 343
- Lacey, P.I. Lestz, S.J. “Effect of Low Lubricity Fuels on Diesel Injection Pumps, Part I: Field Performance,” SAE Technical Paper No. 920823 SAE International Congress and Exposition Detroit, MI February 24-28 1992
- Lacey, P.I. Lestz, S.J. “Effect of Low Lubricity Fuels on Diesel Injection Pumps, Part II: Laboratory Evaluation,” SAE Technical Paper No. 920824 SAE International Congress and Exposition Detroit, MI February 24-28 1992
- Lacey, P.I. “Evaluation of Oxidative Corrosion in Diesel Fuel Lubricated Contacts,” Tribology Transactions 37 2 1994 253 260
- Lacey, P.I. “Development of a Lubricity Test Based on the Transition From Boundary Lubrication to Severe Adhesive Wear in Fuels,” Lubrication Engineering 50 10 October 1994
- Lacey, P.I. “Draft Test Procedure for the U.S. Army Scuffing Load Wear Test,” Belvoir Fuels and Lubricants Research Facility, Southwest Research Institute P.O. Drawer 28510, San Antonio, TX 78228-0510
- Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE), Method D 5001-89 ASTM 1916 Race Street, Philadelphia, PA 1981
- Meeting Minutes International Standards Organization (ISO), Technical Committee 22, Subcommittee 7, Working Group 6 17 October 1994 Baltimore, MD
- Federal Specification for Fuel Oil, Diesel, W-F-800E July 13 1994 Std. Document Order Desk, Bldg. 4D, 700 Robbins Ave., Philadelphia, PA 19111-5094
- Report of the Diesel Fuel Task Force February 18 1994
- Military Specification MIL-I-25017E “Inhibitor Corrosion/Lubricity Improver, Fuel Soluble (Metric),” 15 June 1989
- Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy, Method D 4294-90 ASTM 1916 Race Street, Philadelphia, PA 1981
- Standard Test Method for Determination of Aromatic Content of Diesel Fuels by Supercritical Fluid Chromatography, Method D 5186 ASTM 1916 Race Street, Philadelphia, PA 1991
- Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids and the Calculation of Dynamic Viscosity, Method D 445-88 ASTM 1916 Race Street, Philadelphia, PA 1988
- Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels by Supercritical Fluid Chromatography, Modified Version of ASTM D 5186 Western States Petroleum Association Testing Methodologies Working Group
- Lacey, P.I. Westbrook, S.R. “The Effect of Increased Refining on the Lubricity of Diesel Fuel,” 5th International Conference on Stability and Handling of Liquid Fuels Rotterdam, the Netherlands 3-7 October 1994
- Physical Constants of Hydrocarbons C 1 to C 10 , American Society for Testing and Materials data series publication DS 4A 1968 ASTM 1916 Race Street, Philadelphia, PA 19103