This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Flame Shape Determination Using an Optical-Fiber Spark Plug and a Head-Gasket Ionization Probe
Annotation ability available
Sector:
Language:
English
Abstract
A method for determining the flame contour based on the flame arrival time at the fiber optic (FO) spark plug and at the head gasket ionization probe (IP) locations has been developed. The experimental data were generated in a single-cylinder Ricardo Hydra spark-ignition engine. The head gasket IP, constructed from a double-sided copper-clad circuit board, detects the flame arrival time at eight equally spaced locations at the top of the cylinder liner. Three other IP's were also installed in the cylinder head to provide additional intermediate data on flame location and arrival time. The FO spark plug consists of a standard spark plug with eight symmetrically spaced optical fibers located in the ground casing of the plug. The cylinder pressure was recorded simultaneously with the eleven IP signals and the eight optical signals using a high-speed PC-based data acquisition system.
Based on these flame arrival times, the development of the flame radius in each direction from the center of the spark plug toward each head gasket IP (Ri=f(time)) was estimated using a cubic spline interpolation. The flame contour for a given time is then drawn from a spline interpolation. The engine was run at various spark timing settings, speeds, and relative air-fuel ratios for two distinct flow configurations. This curve fitting methodology produces reasonable flame shape contours and therefore provides a useful tool for studying cycle-to-cycle variations in the combustion rate as well as the effect of different flow characteristics on flame development and end-gas region geometry and location.
Recommended Content
Authors
Topic
Citation
Salvat, O., Cheng, A., Cheng, W., and Heywood, J., "Flame Shape Determination Using an Optical-Fiber Spark Plug and a Head-Gasket Ionization Probe," SAE Technical Paper 941987, 1994, https://doi.org/10.4271/941987.Also In
References
- Dyer, T.M. “New Experimental Techniques for In-Cylinder Engine Studies” Trans. SAE 94 196 1985 SAE paper 850396
- Amann, C. A. “Classical Combustion Diagnostics for Engine Research” Trans. SAE 94 168 1985
- Witze, P. O. Hall, M. J. Wallace, J. S. “Fiber-Optic Instrumented Spark Plug for Measuring Early Flame Development in Spark Ignition Engines” Trans. SAE 97 813 1988 SAE paper 881638
- Witze, P. O. Hall, M. J. Bennet, M. J. “Cycle-Resolved Measurements of Flame Kernel Growth and Motion Correlated with Combustion Duration” Trans. SAE 99 74 1990 SAE paper 900023
- Bianco, Y. Cheng, W. K. Heywood, J. B. “The Effect of Initial Flame Kernel Condition on Flame Development in SI Engines” SAE paper 912402
- Lord, D. D. Kim, Y. Anderson, R. W. Brehob, D. D. “Fiber Optic Spark Plug Analysis of Early Flame Kernel Characteristics in Production Engines with Various Charge Motions” SAE paper 930463
- Meyer, R. Kubesh, J. T. Shahed, S. M. “Simultaneous Application of Optical Spark Plug Probe and Head Gasket Ionization Probe to a Production Engine” SAE paper 930464 1993
- Curry, S. “A Three-Dimensional Study of Flame Propagation in a Spark Ignition Engine” Trans. SAE 71 628 1963
- McDougal, J. A. “Separation of Variables in an Ion Gap Controlled Engine” 1990
- Witze, P. O. “Cycle-Resolved Multipoint Ionization Probe Measurements in a Spark Ignition Engine” Trans. SAE 98 2074 1989 SAE paper 892099
- Witze, P. O. Bopp, S. C. “Investigation of In-Cylinder Fluid Motion Using a Head Gasket Instrumented with Ionization Probes“ Trans. SAE 100 1227 1991 SAE paper 910719
- Witze, P. O. Green, R. M. “Determining the Location of End-Gas Autoignition Using Ionization Probes Installed in the Head Gasket” SAE paper 932645
- Nicholson, D. E. Witze, P. O. “Flame Location Measurements in a Production Engine Using Ionization Probes Embodied in a Printed-Circuit-Board Head Gasket” SAE paper 930390
- Cheng, A., S. “The Head Gasket Ionization Probe as a Combustion Diagnostic for Spark Ignition Engines” Department of Mechanical Engineering, Massachusetts Institute of Technology 1994
- Cheung. H. Heywood J. B. “Evaluation of a One-Zone Burn Rate Analysis Procedure Using Production SI Engine Pressure Data” SAE paper 932749 1993
- Keck, J., C. “Turbulent Flame Structure and Speed in Spark-Ignition Engines” Nineteenth Symposium (International) on Combustion The Combustion Institute 1982 1451 1466