This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Modeling of Diesel Spray Impingement on a Flat Wall
Annotation ability available
Sector:
Language:
English
Abstract
This paper presents an analysis using a model of the dispersion process of a Diesel spray impinging on a flat wall. The objective is to simulate the spray / wall interaction process inside Diesel engines. This analysis has two parts: one for non - evaporative spray and the other for evaporative spray. For the non - evaporative spray analysis, a single spray of n - tridecane was injected at high - pressure from a single hole nozzle into a quiescent atmosphere at room - temperature. The spray impinged vertically on the wall at room temperature. Thus, the wall temperature Tw was less than the saturation temperature Tsat of the fuel, that is the boiling temperature. A new submodel including fuel film formation on the wall, its breakup process due to droplet impingement and the dispersion process of breakup - droplets was developed. Also, the droplet density distribution was measured experimentally by the laser light extinction method. For the evaporative spray analysis, the fuel spray was injected into a high - pressure and high - temperature atmosphere and impinged on a wall at a temperature of 550 K. Here, Tw was above Tsat. A submodel for the heat transfer from the wall to the droplet, the breakup behavior of impinging droplets owing to boiling at the liquid - solid interface and the dispersion process of breakup - droplets was considered. Further, the vapor and the liquid phases in the spray were separated experimentally by using exciplex fluorescence method. The new submodels for both temperature conditions were incorporated into the KIVA code and compared with the spray/wall impingement model of Naber & Reitz to calculate the dispersion process. It was found in 2 - dimensional calculations that the new submodels have better qualitative agreement with the experimental one, when compared with that of Naber & Reitz.
Recommended Content
Authors
Citation
Jiro, S., Kobayashi, M., Iwashita, S., and Fujimoto, H., "Modeling of Diesel Spray Impingement on a Flat Wall," SAE Technical Paper 941894, 1994, https://doi.org/10.4271/941894.Also In
References
- Fujimoto, H. Saito, M. Minoura, A. Katsura, N. Cho, I.Y. Senda, J. “Characteristics of a Diesel Spray Impinging on a Flat Wall” ICLASS - '88 A9 1 439 446 1988
- Katsura, N. Saito, M. Senda, J. Fujimoto, H. “Characteristics of a Diesel Spray Impinging on a Flat Wall” SAE Trans. 98 890264 191 207 1989
- Fujimoto, H. Senda, J. Nagae, M. Hashimoto, A. “Characteristics of a Diesel Spray Impinging on a Flat Wall” Int. Sympo. COMODIA 90 193 198 1990
- Senda, J. Fukami, Y. Tanabe, Y. Fujimoto, H. “Visualization of Evaporative Diesel Spray Impinging upon Wall Surface by Exciplex Fluorescence Method” SAE Trans. 101 920578 1 10 1992
- Senda, J. Tanabe, Y. Fujimoto, H. “Visualization and Quantitative Analysis on Fuel Vapor Concentration in Diesel Spray” Advanced Study Institute on Unsteady Combustion II 27.1 27.6 1993
- Amsden, A. A. Ramshaw, J. D. O'Rourke, P. J. Dukowicz, J.K. “KIVA: A Computer Program for Two - and Three - Dimensional Fluid Flow with Chemical Reactions and Fuel Sprays” Los - Alamos National Laboratory report, LA-10254-MS 1985
- Naber, J.D. Reitz, R.D. “Modeling Engine Spray / Wall Impingement” SAE Paper, No. 881316 1 23 1988
- Wachters, L. H. J. Westerling, N. A. J. “The Heat Transfer from a Hot Wall to Impinging Water Drops in the Spheroidal State” Chem. Eng. Sic. 21 1047 1057 1966
- Naber, J. Enright, B. Farrell, P. “Fuel Impingement in a Direct Injection Diesel Engine” SAE Paper No. 881316 1 14 1988
- Senda, J. Takeuchi, K. Sato, Y. ICLASS - 82 14 4 397 404 1982
- Senda, J. Takeuchi, K. Sato, Y. “Atomization of Spray Droplet Impinging upon a Hot Surface Internal Combustion Engine 21 268 9 18 1982
- Senda, J. Yamada, K. Takeuchi, K. Miki, H. “Deformation and Breakup Behavior of a Small Droplet Impinging upon a Hot Surface” Trans. of JSME 52 481 3372 3379 1986
- Senda, J. Yamada, K. Fujimoto, H. Miki, H. “The Heat - Transfer Characteristics of a Small Droplet Impinging upon a Hot Surface” JSME Int. Journal, Series II 3 1 105 111 1988
- Kurabayashi, T. Karasawa lida, K. JSME 175 153 156 1967