This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
In-Cylinder Gas Velocity Measurements Comparing Crankcase and Blower Scavenging in a Fired Two-Stroke Cycle Engine
Annotation ability available
Sector:
Language:
English
Abstract
The in-cylinder flow field of a Schnürle (loop) scavenged two-stroke engine has been examined under conditions simulating both blower and crankcase driven scavenging. Measurements of the radial component of velocity were obtained along the cylinder centerline during fired operation at delivery ratios of 0.4, 0.6, and 0.8. Both mean velocity profiles and root mean square velocity fluctuations near top center show a strong dependence on the scavenging method. Complementary in-cylinder pressure measurements indicate that combustion performance is better under blower driven scavenging for the engine geometry studied.
IN THE PAST TEN YEARS the engine research and development community has demonstrated a renewed interest in two-stroke engine technology. Many manufacturers have new engine designs operating on test stands and in prototype vehicles being road tested. This recent development activity has resulted in the adoption of both crankcase and external blower scavenged designs as the baseline engine configurations. Both design concepts have their advantages and disadvantages, and there seem to be situations where each is best used.
Crankcase scavenging with piston-controlled porting and dry-sump lubrication is certainly the simplest engine configuration from the size/weight/complexity point-of-view. The General Motors CDS2 design and one of the Orbital Engine Company designs are examples of current crankcase scavenged configurations (Wyczalek [1]*). This design offers the potential of improved fuel economy at light load operation due to lower pumping and friction losses. Some disadvantages, however, include the need to either mix or inject lubricating oil into the intake charge and a crankcase design requiring individual cylinder sealing along with the use of roller bearings. In addition, the crankcase pumping by the reciprocating piston leaves little flexibility in controlling the scavenging flow, leading under some conditions to undesirably low scavenging efficiency. The scavenging efficiency can be somewhat improved using crankcase compression with uni-flow scavenging, which requires the use of valves and valve control mechanisms with the associated increase in complexity.
External blower scavenging can be implemented in different configurations. For example, Subaru uses piston-controlled porting and a screw-type compressor; Toyota uses camshaft-driven valves and a roots-type blower; and Orbital employs flywheel mounted centrifugal blowers with piston-controlled porting in two of their current designs (Wyczalek [1]). These blower scavenged engines use wet-sump lubrication systems. The use of an external blower itself adds to the mechanical complexity of the engine, and the additional use of valves further increases the complexity. On the other hand, the use of an external blower and valves can lead to an improvement in the control of the scavenging process and, in turn, an improvement in engine performance. Furthermore, wet-sump lubrication allows the use of common, inexpensive journal bearings and a less-complex crankcase arrangement along with a reduced concern over exhaust catalyst poisoning due to use of improper lubrication oil.
Previous investigations of the scavenging process have been focused on one or the other scavenging mode and not on a comparison of the two. In addition to a global understanding of the good and bad features of the two scavenging methods, a direct comparison of the two could provide engine designers with additional insight as to which method is more suitable for their application. The intent of the work reported in this paper is to characterize and compare the in-cylinder flow fields associated with both crankcase and external blower scavenging configurations, in an engine that can be operated in either mode. In-cylinder pressure measurements are also reported to provide a relative indication of the combustion performance associated with the two scavenging methods. A comparison of this sort provides
information on the general features associated with each flow field, and the possible suitability of each configuration to specific engine geometries.
Recommended Content
Authors
Topic
Citation
Miles, P., Green, R., and Witze, P., "In-Cylinder Gas Velocity Measurements Comparing Crankcase and Blower Scavenging in a Fired Two-Stroke Cycle Engine," SAE Technical Paper 940401, 1994, https://doi.org/10.4271/940401.Also In
Two-Stroke Engines: Theoretical and Experimental Investigations
Number: SP-1019; Published: 1994-03-01
Number: SP-1019; Published: 1994-03-01
References
- Wyczalek, F.A. “Two-Stroke Engine Technology in the 1990's,” SAE Paper No. 910663 1991
- Groff, E.G. Fansler, T.D. Matthes, W.R. General Motors NAO R&D Center Warren, Ml private communication 1993
- Green, R.M. Cousyn, B.J. “An Optical Research Engine for the Study of Two-Stroke Cycle In-Cylinder Phenomena,” COMODIA 90, International Symposium on Diagnostics and Modeling of Combustion in Internal Combustion Engines Kyoto, Japan 1990
- Bopp, S.C. Cousyn, B.J. Green, R.M. Witze, P.O. “Experimental Study of the Scavenging and Combustion Processes in a Two-Stroke Cycle Research Engine,” Trans. SAE 101 245 1992
- Groff, E.G. General Motors NAO R&D Center Warren, Ml private communication 1993
- Morel, T. Flemming, M.F. LaPointe, L.A. “Characterization of Manifold Dynamics in the Chrysler 2.21 S.I. Engine by Measurements and Simulation” SAE Paper No. 900679 1990
- Ikeda, Y. Ohhira, T. Takahashi, T. Nakajima, T. “Misfiring Effects on Scavenging Flow at Scavenging Port and Exhaust Pipe in a Small Two-Stroke-Engine,” SAE Paper No. 930498 1993
- Obokata, T. Hanada, N. Kurabayashi, T. “Laser Doppler Anemometer Measurement of Gas Flow in the Wedge-Type Combustion Chamber of a Two-Cycle Spark Ignition Engine,” Combustion in Engines - Technology and Applications Institution of Mechanical Engineers, Mechanical Engineering Publications Ltd. 213 1988
- Fansler, T.D. French, D.T. “The Scavenging Flow Field in a Crankcase Compression Two-Stroke Engine - A Three Dimensional Laser Velocimetry Survey,” Trans. SAE 101 581 1992
- Okuyama, L. Kousaka, Y. Tohge, N. Yamamoto, S. Wu, J.J. Flagan, R.C. Seinfeld, J.H. “Production of Ultrafine Metal Oxide Aerosol Particles by Thermal Decomposition of Metal Alkoxide Vapors,” AIChE J . 32 12 2010 1986
- Witze, P.O. Baritaud, T.A. “Particle Seeding for Mie Scattering Measurements in Combusting Flows,” Proceedings of the Third International Symposium on Applications of Laser Anemometry to Fluid Mechanics Lisbon July 1986