This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Spray Characteristics of Five-Hole V.C.O Nozzles of a Diesel Electro- Injector
Annotation ability available
Sector:
Language:
English
Abstract
The study of the spray of standard, five-hole, V.C.O. nozzles for D.I. diesel engine has been carried out. Several pictures of the spray have been taken using the back-light photography technique. Injected volume, feeding pressure, injection duration, spray penetration, angle and thickness, and flash delay from the start of injection have been measured both for nozzles of two different manufacturers and for a group of four injectors before and after a fatigue test of about 1500 hours running. Measurements revealed that each spray strongly depends on the needle lift, the back-pressure and the nozzle geometry and that, for the same injector, sprays are totally different from hole to hole. The causes of the most important differences have been attributed at the different hole inclination, their asymmetric feeding conditions (due to the eccentricity between needle and nozzle) and the microdefects caused by drilling operation.
Authors
Citation
Campanella, R., Laforgia, D., Ficarella, A., and Damiani, V., "Spray Characteristics of Five-Hole V.C.O Nozzles of a Diesel Electro- Injector," SAE Technical Paper 940192, 1994, https://doi.org/10.4271/940192.Also In
References
- Joachin, W.F. Beardsley, E.G. “Factor in the Design of Centrifugal Type Injection Valves for Oil Engines” NACA Report No. 268 and 281 1927
- Decorso, S.M. Kemeny, G. “Effect of Ambient and Fuel Pressure on Nozzle Spray Angle” ASME 605 1957
- Allocca, L. Belardini, P. Bertoli, C. Corcione, F.E. De Angelis, F. “Experimental and Numerical Analisys of a Diesel Spray” SAE Paper No. 920576
- Arai, M. Tabata, M. Hiroyasu, H. Shimizu, M. “Disintegration Process and Spray Characterization of Fuel Jet Injected by a Diesel Nozzle” SAE Paper No. 840275
- Brunello, G. Carlevaro, R. Cossali, G. Daminelli, G. Fazzini, G. Va, C.R. Coghe, A. Reggiori, A. “Simultaneus Evaluation of Tip and Drop Velocities in Unsteady Sprays” ATA 43 October 1990
- Burt, R. Troth, K.A. “Penetretion and Vaporization of Diesel Fuel Spray” Proc. Instn. Mech. Engrs. 1969-70 184 147 170
- Hai, N. Jones, P.L. “Comparison of the Various Correlations for Spray Penetration” SAE Paper No. 720776 1972
- Kosaka, H. Won, Y.H. Kamimoto, T. “A Study of Structure of Diesel Sprays Using 2-D Imaging Tecniques” SAE Paper No. 920107 1992
- Schweitzer, H.P. “Penetration of Diesel Spray” Penn. St. Call. Bull (No. 46, July) 1937
- Gray, LT. Jun Meckel, N.T. Mannheimer, R.L “Some Observations on the Liquid Injection Tecnique as a Reserch Tool” SAE Paper No. 660748 1966
- Reitz, R.D. “Atomization and Other Breakup Regimes of a Liquid Jet” Department of Mechanical and Aerospace Engineering, Princeton University September 1978
- Bergwerk, W. “Flow Pattern in Diesel Nozzle Spray Holes” Proc. Instit. Mech. Engrs. 173 655 1959
- Shundoh, S. Komori, M. Tsujimura, K. Kobayashi, S. “NOx Reduction from Diesel Combustion Using Pilot Injection with High Pressure Fuel Injection” SAE Paper No. 920461 1992
- Laforgia, D. Chehroudi, B. Bracco, F.V. “Structure of Spray from Fuel Injection. The FORD DFI-3 Fuel Injection” SAE Paper No. 890313 1989
- Campanella, R. Laforgia, D. Ficarella, A. Damiani, V. De Matthaeis, S. Ricco, M. “V.C.O. Nozzle Characterization” Polytechnic of Bari and ELASIS BA2 Bari December 1992
- Bruni, G. Damiani, V. Laforgia, D. “Study of the Flow of a Multihole V.C.O. Nozzle and Effects on Spray” Praga ILASS Paper No. 1098 1993
- Iiyama, A. Matsumoto, Y. Kawamoto, K. Ohishi, T. “Spray Formation Improvement of a V.C.O. Nozzle for D.I. Diesel Smoke Reduction” IMechE Seminar “Diesel Fuel Injection System” 1992
- Campanella, R. Damiani, V. Laforgia, D. Bruni, G. “Spray Visualization and Hydraulic Characterization of the Holes of a Five-Hole, V.C.O. Nozzle of an Electronically Controlled Diesel Injector” Praga ILASS Paper No. 3119 1993
- Campanella, R. Laforgia, D. Ficarella, A. Damiani, V. De Matthaeis, S. Ricco, M. “Second V.C.O. Nozzle Characterization” Polytechnic of Bari and ELASIS BA2 Bari May 1993
- Campanella, R. Laforgia, D. Ficarella, A. Damiani, V. De Matthaeis, S. Ricco, M. “Comparison Between Two V.C.O. Nozzles” Polytechnic of Bari and ELASIS BA2 Bari July 1993
- Reliability test - FIAT Standard Torino 1992
- Campanella, R. Laforgia, D. Ficarella, A. Damiani, V. De Matthaeis, S. Ricco, M. “Spray Characteristics of Four Electroinjectors After 1500-Hour Running” Polytechnic of Bari and ELASIS BA2 Bari September 1993