This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Investigations on the Design and Performance of Two Types of Hot Surface Ignition Engines
Annotation ability available
Sector:
Language:
English
Abstract
Use of methanol and ethanol in conventional diesel engines is associated with problems on account of the high self ignition temperature of these fuels. The Hot Surface Ignition (HSI) method wherein a part of the injected fuel is made to touch an electrically heated hot surface for ignition, is an effective way of utilizing these fuels in conventional diesel engines. In the present work two types of HSI engines, one using a large ceramic base and the other using a conventional glowplug were developed. These engines were tested with methanol, M.spirit (about 90 % methanol and 10 % ethanol) and diesel. The results of performance, fuel economy emissions and combustion parameters including heat release rates for these fuels with both the types of HSI engines are presented.
Diesel engines are commonly used as primemovers in the mass transportation and agricultural sectors because of their high brake thermal efficiency and reliability. On the other hand, the rapid depletion, rising prices, uncertain supplies and ever increasing requirement of petroleum products have forced researchers to find alternative fuels for diesel engines. The concern for a clean environment has given further impetus to this search.
Methanol and ethanol are the most favoured alternative fuels since they can be produced from a wide variety of feedstock including the renewable ones. They also burn without soot. In general, alcohols are excellent spark ignition engine fuels. However, their use in diesel engines is associated with problems on account of their low cetane numbers, low viscocity & poor missibility with diesel in the presence of moisture. Use of neat alcohol in the diesel engine will need a compression ratio of 23:1 for starting and 20:1 for normal running (1). To use neat alcohols in diesel engines at normal compression ratios, ignition assistance in the form a timed spark or a hot surface is needed.
In the Hot Surface Ignition (HSI) engine a part of the injected fuel is made to touch an electrically heated hot surface for ignition. Combustion then follows in the normal way. The proneness of methanol and to a lesser extent ethanol to surface ignite make them ideal fuels for the HSI engine(2). This method has the following advantages over its spark assisted counterpart (3&4):
-
(a)
Better ignitability,
-
(b)
Possibility to switch off the electrical input at high outputs and
-
(c)
Better multifuel capability.
In the present work two types of HSI engines, the first using a Ceramic Hot Surface and the second using a conventional Glowplug were developed. Both the engines were identical except for the ignition source. Experiments were carried out to obtain the performance, fuel economy, emissions and combustion parameters using alcohols and diesel at a compression ratio of 16.9.
Recommended Content
Authors
Topic
Citation
Ramesh, A., Nagalingam, B., and K. V., G., "Investigations on the Design and Performance of Two Types of Hot Surface Ignition Engines," SAE Technical Paper 921632, 1992, https://doi.org/10.4271/921632.Also In
References
- Siebers Dennis L. Edwards C.F. ‘Autoignition of Methanol and Ethanol Sprays under Diesel Engine Conditions’ SAE Paper No 870558
- Pischinger Franz F. Hilger U. Bartunek B. Adams W. Walder G.Finster ‘Suitability of the Hot Surface Ignition Engine for Using Alcohol Fuels ’ VI International Symposium on Alcohol Fuels Technology Paris, France 1986 272 277
- Imoto K. Kiyota Y. ‘New Combustion System for the Methanol Fuelled IDI Diesel Engine ’ VI International Symposium on Alcohol Fuels Technology Paris, France 1986 226 271
- Ramesh A. ‘Investigations on the Design and Performance of Two types of Hot Surface Ignition engines’ Ph.D Thesis Department of Mechanical Engineering Indian Institute of Technology Madras, India 1990
- Browning L.H. Pefley P.K. ‘Thermokinetic Modelling of Methanol Combustion Phenomenon with Application to Spark Ignition Engines’ III International Symposium on Alcohol Fuels Technology Asilomar, California, U.S.A. 1979 1
- ‘Basic Considerations in the Combustion of Hydrocarbon fuels with Air’ NACA report No. 1300 102 108
- Enomoto Kenjiro Furuhama Shoichi Nishiguchi Tomoyuki ‘Ignitability of Hydrogen-Air Mixture by Hot Surface and Hot Gases in Hydrogen Fuelled Engine’ JSME Review July 1981 24 29
- Ramesh A. Nagalingam B. Gopalakrishnan K.V. ‘A Simple Method to obtain the Heat release Rates of a Diesel engine using a Signal Ananyser’ X National Conference on I.C. Engines and combustion Rajkot, India 1987 PA55 PA60
- Singal S.K. Semval P.B. Kumar D. Pundir B.P. ‘Combustion Rate Analysis of a Surface ignition Methanol engine’ X National Conference on I.C. Engines and Combustion Rajkot, India 1987 AF103 AF110
- Nanni H. Domschke A.D. Brunetti F. Rozov V. Rosa F. de o Borba M.L. De Abreu R.S. ‘Use of Glowplugs in Order to obtain Multifuel Capability in Diesel Engines’ IV International Symposium on Alcohol Fuels Technology Brazil October 1980 3 1075 1082
- Nanni H. Domsche A.G. Brunetti F. Rozov V. Rosa F. de o Borba M.L. Russo R. Koschar M. Madureria O. ‘New Developments in Multifuel Capability of Diesel engines through the use of Glowplugs’ V International Symposium on Alcohol Fuels Technology Auckland, New Zealand 1982