This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Piston Top Shapes and Their Influence Upon Otto Cycle Combustion
Annotation ability available
Sector:
Event:
SAE Brasil
Language:
English
Abstract
Combustion in reciprocating engines relies on in-cylinder gas motion to speed up the process and enhance burning efficiency. A number of factors capable of influencing such motion can be listed. Among the most important are intake port and piston top geometry. The latter normally referred to as combustion bowl shape is a subject of intense research activity in the Diesel field,in stark contrast to the mild endeavours prevailing in the Otto-cycle partisanship. However, today's environmental and energy resources availability considerations demand that cleaner and more fuel efficient engines have to be made available. Homogeneous mixture Otto-cycle powerplant improvements in fuel economy are hampered by knock incidence, among other factors. It is known that piston top features do interact with the combustion flame front in both negative or positive fashion. In order to better understand how sensitive this interaction is, four piston top shapes were tested in a 4-cyl. SI engine that is representative of the current, high production volume generation. A single cylinder research engine was also used for preliminary testing. The influence of slight differences in piston top geometry upon the Brake Specific Fuel Consumption (BSFC), the Lean Burning Limit (LBL), the Peak Combustion Pressure (Pk) and the Knock Avoidance Margin (KAM) were investigated. Tops were shaped as follows:
The flat topped pistons performances of both engines were taken as references. From the stand-point of BSFC, the 4 cyl. fitted with the convex top piston showed no improvement, the wedge squish-enhancing exhibited about 1% less fuel consumption while the concave, radial squish-enhancing version decreased BSFC by as much as 7.3%. The convex proved itself to have the highest KAM and leanest LBL burning tolerance of all versions tested. Under WOT condition, all versions developed about the same power (within +/- 3%) at 5200 rpm. Maximum torque, developed at 2800 rpm, was also consistent and within +/- 2% except for the concave piston. For this version, the incidence of knocking limited max. torque to 93% of the reference value. The research unit exhibited the same trends except for the BSFC. In this case, it was 4% lower with the convex topped piston. Conclusions of this work are:
Recommended Content
Authors
Topic
Citation
Azevedo, M., "Piston Top Shapes and Their Influence Upon Otto Cycle Combustion," SAE Technical Paper 921465, 1992, https://doi.org/10.4271/921465.Also In
References
- Huber, Eugen Prescher, K. Reduction of Air Pollution by Internal Modification of a SI Engine MTZ 37 1976 4
- Nagayama, I. Araki, Y. Iioka, Y. Effects of Swirl and Squish on SI Engine Combustion and Emission SAE 770217
- Lucas, G. G. Brunt, M.F The Effect of Combustion Chamber Shape on the Rate of Combustion in a SI Engine SAE 820165
- Yoshida, Masahiro An Effect of the Topland Form of the Piston on Hydrocarbon Emissions of a SI Engine MTZ 41 1980 3
- Mikulec, A. Kent, J. C Tabaczynski, R. J The Effect of Swirl on Combustion in a Pancake Chamber SI Engine SAE 880200
- Bolt, J. A Holkeboer, D. H Lean Fuel/Air Mixtures for High Compression SI Engines SAE 1961 Summer Meeting 380D
- Noguchi, M. Sanda, S. Nakamura, N. Development of TOYOTA Lean Burn Engine SAE 760757
- Lancaster, D. R Krieger, R. B Sorenson, S. C. Hull, W. L. Effects of Turbulence on SI Engine Combustion SAE 760160
- Varde, K. S. Lubin, M. J. The Roll of Connecting Nozzle and the Flame Initiation Point in the Performance of a Dual Chamber Stratified Charge Engine SAE 741161
- Wyczalek, F. A et alli EFI Prechamber Torch Ignition of Lean Mixtures SAE 750351
- Nakamura, H. et alli Development of a New Combustion System in Gasoline Engines SAE 780007
- Becker, Clauspeter
- Harada, Masanori et alli Nissan NAPS Z Engine Fuel Economy and Low Nox Emissions SAE 810010
- Audi 5 Cylinder Engine Characteristics SAE 770112
- Swirl Effects Upon Combustion SAE 900353
- Hirotomi, T. et alli Yamamasu, M. Study of Induction Swirl in a SI Engine SAE 810496
- Mikulic, L. Development of High Compression, Fast Burn Systems for Passenger Car and Light Duty Commercial Vehicle Engines. 5th International Paciific Conference Nov. 1989
- Quader, A. A. What Limits Lean Operation in SI Engines-Flame Initiation or Propagation? 760760
- Namazian, M. Heywood, J. B. Flow in the Piston-Cylinder-Ring Crevices of a SI Engine SAE 820088
- Saika, T. Korematsu, K. Flame Propagation into the Ring Crevice of a SI Engine SAE 861528
- Cornetti, G. M. et alli Engine Failure and High Speed Knock SAE 770147
- Quissek, F. AVL Communication
- Nakamura, N. et alli Multipoint SI for Lean Combustion SAE 852092
- Matsui, K. Tanaka, T. Measurement of Local Mixture Strength at Spark Gap of SI Engines SAE 790483
- Lech, G. Harms, V. MTZ 47 1986