This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Empirical-Numerical Simulation Technique for Improving the Quality of Rolled Rods by Roll Pass Design
Annotation ability available
Sector:
Language:
English
Abstract
Improper roll pass designs can lead to either underfill which results in the formation of hairline cracks on the surface of the finished bars or overfill which results in roll overloading and the formation of fins. Therefore to reduce downtime, and improve yield and quality, it becomes important to design an acceptable roll pass in reasonable time. This paper presents a methodology for roll pass design which uses a three dimensional finite element technique along with an empirical procedure to arrive at an iterative scheme for reducing the number of passes and improving metal flow in the passes. This methodology is applied to improving an existing seven pass square - to - round rolling sequence, resulting in the reduction of the number of passes and improved distributions of effective strains in the rolled product.
Authors
Citation
Shivpuri, R., Shin, W., and Mehrotra, R., "Empirical-Numerical Simulation Technique for Improving the Quality of Rolled Rods by Roll Pass Design," SAE Technical Paper 920783, 1992, https://doi.org/10.4271/920783.Also In
References
- Roberts, William L. 1983 Hot Rolling of Steel New York. NY Marcel Dekker
- Altan, T. Oh, S. Gegel, H. 1983 Metal Forming: Fundamentals and Applications American Society for Metals
- Raghupathi, P. S. Altan, T. 1982 Roll pass design in shape rolling: A survey of German technical literature Battelle Columbus Labs
- Wusatowski, Z. 1957 Average stretching strains in irregular roll passes Neue Huette 24 35
- Neumann, H. Schulze, R. 1974 Programmed roll pass design for blocks Neue Huette 460 471
- Lendl, A. E. 1948 Rolled bars - Calculation of spread between non-parallel roll surfaces Iron and Steel 397 402 Sept. 1948
- Lendl, A. E. 1948 Rolled bars - Part II - Application of spread calculation to pass design Iron and Steel 601 604 Dec. 1948
- Lendl, A. E. 1949 Rolled bars - Part III - Application of spread calculation to diamond passes Iron and Steel 499 501 Nov. 1949
- Ekelund, S. 1927 Jernkontorets Annaler III 39 97
- Kennedy, K. F. Lahoti, G. D. Altan, T. 1982 Computer aided analysis of metal flow, stresses and roll pass design in rolling of rods AISE J.
- Sevenler, K. Raghupathi, P. S. Altan, T., May 1986 Spread and bulging in bar and rod rolling using flat rolls Iron and Steel Engineer 57 62
- Oh, S. I. Kobayashi, S. 1975 An approximate method for a three-dimensional analysis of rolling Int. J. Mech. Sci. 17 293 305
- Shima, S. Mori, K. Oda, T. Osakada, K. 1980 Rigid-plastic finite element analysis of strip rolling Proc. 4th International Conf. Prod. Eng. 82 87
- Li, G. Kobayashi, S. 1982 Rigid-plastic finite-element analysis of plane strain rolling ASME Trans., Journal of Engineering for Industry 104 55 64
- Mori, K. Osakada, K. Oda, T. 1982 Simulation of plane-strain rolling by the rigid-plastic finite element method Int. J. Mech. Sci. 24 519 527
- Mori, K. Osakada, K. 1982 Simulation of three-dimensional rolling by the rigid-plastic finite element method Numerical Methods in Industrial Forming Processes 747 756
- Mori, K. Osakada, K. 1984 Simulation of three-dimensional deformation in rolling by the finite element method Int. J. Mech. Sci. 26 515 525
- Bertrand, C. David, C. Chenot, J. L. Buessler, P. 1986 Stresses calculation in finite element analysis of three-dimensional hot shape rolling Proceedings of the NUMIFORM 86 207 212
- Mori, K. Osakada, K. 1989 Finite element simulation of three-dimensional deformation in shape rolling Proc. NUMIFORM 89 Thompson et al. (eds) Balkema, Rotterdam
- Bertrand-Corsini, C. Montmittonnet, P. Chenot, J. L. et al. 1989 A three-dimensional analysis of hot rolling with a steady state thermomechanical approach Proc. NUMIFORM 89 Thompson et al (eds) Balkema, Rotterdam
- Kiuchi, M. Yanagimoto, J. 1988 Computer aided simulation of shape rolling processes North American Manufacturing Research Conference Proceedings 34 40
- Park, J. J. Oh, S. I. 1990 Application of three dimensional finite element analysis to shape rolling processes ASME Trans., Journal of Engineering for Industry 112 36 46
- Kim, N. Kobayashi, S. Altan, T. 1990 Three-dimensional analysis and computer simulation of shape rolling by the finite and slab element method Int. J. Mach. Tools and Manufacture
- Kim, N. Lee, S. M. Shin, W. Shivpuri, R. 1990 Simulation of square-to-oval single pass rolling using a computationally effective finite and slab element method Trans. ASME, J. Engr. for Industry
- Shin, W. Lee, S. M. Shivpuri, R. Altan, T. 1990 Finite-slab element investigation of square-to-round multipass shape rolling J. Materials Processing Technology
- Lee, S. M. Shin, W. Shivpuri, R. 1990 Investigation of Two Square-to-Round Multipass Rolling Sequences by the Finite and Slab Element Method Int. J. Mach. Tools and Manufacture
- Shin, W. 1990 Studies on the improvement of roll pass sequence in rolling of shapes using finite and slab element method program “TASKS” The Ohio State University