This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Multi-Dimensional Modeling of Turbulent Premixed Charge Combustion
Annotation ability available
Sector:
Language:
English
Abstract
Existing models of combustion for multi-dimensional engine flow calculations have problems that limit their usefulness for investigating combustion dependent engine design issues. An alternative model has been formulated that is applicable to premixed charge combustion in engines. The model is robust enough to treat combustion in the bulk and near wall flow regions, and includes a mechanism for flame quenching at the wall. Combustion is represented in terms of separate entrainment and burn-up processes, which is similar to the two zone models commonly used in engine cycle simulations.
Calculations have been performed of one-dimensional radial flame propagation in a cylindrical chamber, which is initially filled with a homogeneous fuel-air mixture. Deficiencies in existing combustion models have been demonstrated for this case. The performance of the new combustion model was assessed by studying flame propagation over a range of initial gas conditions typical of engines. The results show that the model gives a physically plausible representation of flame behaviour for all conditions considered. Good agreement is obtained with engine measurements of flame speed. Flame quench distances are within the range expected to occur in engines, as given by prior experimental studies presented in the literature.
Further calculations were performed of two-dimensional flame propagation in a pancake geometry combustion chamber. Tangential quenching at the head and piston surfaces gives the flame front a concave shape as it progresses towards the liner. Overall, the calculations demonstrate that the new model shows great potential for providing an accurate representation of turbulent combustion in practical engine geometries. This provides motivation for future development and validation of the model.
Authors
Citation
Jennings, M., "Multi-Dimensional Modeling of Turbulent Premixed Charge Combustion," SAE Technical Paper 920589, 1992, https://doi.org/10.4271/920589.Also In
References
- Abraham, J. Williams, F. A. Bracco, F. V. 1985 ‘A Discussion of Turbulent Flame Structure in Premixed Charges’ SAE Paper 850345
- Beretta, G. P. Rashidi, M. Keck, J. C. 1983 ‘Turbulent Flame Propagation and Combustion in Spark Ignition Engines’ Combustion and Flame 52 217 245
- Brandstatter, W. Johns, R. J. R. 1983 ‘The Application of a Probability Method to Engine Combustion Modeling’ Institute of Mechanical Engineers Paper C58/83
- Butler, T. D. Cloutman, L. D. Dukowicz, J. K. Ramshaw, J. D. Krieger, R. B. 1980 ‘Toward a Comprehensive Model for Combustion in a Direct Injection Stratified Charge Engine’ Combustion Modeling in Reciprocating Engines Plenum Press New York
- Cheng, W. K. Diringer, J. A. 1991 ‘Numerical Modeling of SI Combustion with a Flame Sheet Model’ SAE Paper 910268
- Delamare, L. Borghi, R. Gonzalez, M. 1981 ‘The Modeling and Calculation of a Turbulent Premixed Flame Propagation in a Closed Vessel: Comparisons of Three Models with Experiments’ SAE Paper 910265
- Ferguson, C. R. Keck, J. C. 1977 ‘On Laminar Flame Quenching and Its Application to Spark Ignition Engines’ Combustion and Flame 28 197 205
- Gibson, D. H. Mahaffey, W. A. Mukerjee, T. 1990 ‘In-Cylinder Flow and Combustion Modeling of 1.7L Caterpillar Engine’ SAE Paper 900253
- Goolsby, A. D. Haskell, W. W. 1976 ‘Flame Quench Distance Measurements in a CFR Engine’ Combustion and Flame 26 105 114
- Gosman, A. D. 1986 ‘The EPISO-HC Code for Homogeneous Combustion Engine Prediction’ JRC Workshop June 18 Imperial College London
- Groff, E. G. Matekunas, F. A. 1980 ‘The Nature of Turbulent Flame Propagation in a Homogeneous Spark Ignited Engine’ SAE Paper 800133
- Jennings, M. J. Morel, T. 1990 ‘An Improved Near Wall Heat Transfer Model for Multi-Dimensional Engine Flow Calculations’ SAE Paper 900251
- Jennings, M. J. Morel, T. 1991 ‘A Computational Study of Wall Temperature Effects on Engine Heat Transfer’ SAE Paper 910459
- Johns, R. J. R. 1984 ‘A Unified Method for Calculating Engine Flows’ ASME Paper 84-DGP-18
- Kuo, K. K. 1986 Principles of Combustion John Wiley and Sons New York
- Lancaster, D. R. Krieger, R. B. Sorenson, S. C. Hull, W. L. 1976 ‘Effects of Turbulence on Spark Ignition Engine Combustion’ SAE Paper 760160
- Lavoie, G. A. 1978 ‘Correlations of Combustion Data for SI Engine Calculations - Laminar Flame Speed, Quench Distance and Global Reaction Rates’ SAE Paper 780229
- Magnussen, B. F. Hjertager, B. H. 1976 ‘On Mathematical Modeling of Turbulent Combustion with Special Emphasis on Soot Formation and Combustion’ Sixteenth Symposium on Combustion The Combustion Institute
- Morel, T. Wahiduzzaman, S. Tree, D. R. DeWitt, D. P 1987 ‘Effect of Speed, Load and Location on Heat Transfer in a Diesel Engine - Measurements and Predictions’ SAE Paper 870154
- Rhodes, D. B. Keck, J. C. 1985 ‘Laminar Burning Speed Measurements of Indolene-Air-Diluent Mixtures at High Pressures and Temperatures’ SAE Paper 850047
- Singh, T. Surakomol, K. 1979 ‘Mathematical Modeling of Combustion Process in a Spark-Ignition Engine’ SAE Paper 790354
- Tabaczynski, R. J. 1976 ‘Turbulence and Turbulent Combustion in Spark Ignitiion Engines’ Progress in Energy and Combustion Science 2 143 165
- Tabaczynski, R. J. Trinker, F. H. Shannon, B. A. S. 1980 ‘Further Refinement and Validation of a Turbulent Flame Propagation Model for Spark Ignition Engines’ Combustion and Flame 39 111 121
- Westbrook, C. K. Dryer, F. L. 1981 ‘Simplified Reaction Mechanisms for the Oxidation of Hydrocarbon Fuels in Flames’ Combustion Science and Technology 27 31 43