This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Multidimensional Port-and-Cylinder Gas Flow, Fuel Spray, and Combustion Calculations for a Port-Fuel-Injection Engine
Annotation ability available
Sector:
Language:
English
Abstract
An existing multidimensional in-cylinder flow code, KIVA, was modified to conduct port-and-cylinder gas flow, fuel spray, and combustion calculations in a port-fuel-injection engine. The effect of a moving valve with a stem was modeled using a novel internal obstacle technique in which the valve was represented by a group of discrete computational particles. Previously developed spray and combustion models were used to simulate fuel injection and combustion processes for a solid-cone shaped, pressure-atomized spray with isooctane as the fuel. The spray model was further modified to handle interactions between the spray drops and the valve.
The model was applied to a generic port-fuel-injection engine with variations in port orientation, spray cone angle, and valve configuration (without and with a 180-degree shroud). Calculation results for gas flow, fuel spray, and combustion indicated that the effect of a moving valve was modeled adequately using the new internal obstacle treatment technique. In particular, the proposed spray/valve interaction submodel seems to handle the impingement process between the spray drops and the valve quite well.
The results also indicated that the spray cone angle and valve shroud had strong influences on the time history of injected fuel that enters the cylinder before intake valve closing and on the distribution of fuel-air mixture in the cylinder at the time of the spark. For excessive spray/valve and/or spray/port wall impingement, the amount of present-cycle-injected fuel entering the cylinder can be greatly reduced.
Engines with port-fuel-injection (PFI) systems have become popular as a means of improving vehicle performance through faster response and higher specific output and for improving exhaust emission control [1]*. The combustion process in PFI engines is known to be affected strongly by fuel-air mixing, which is governed by the gas flow and fuel-injection processes. The complex and transient nature of these processes, however, makes it extremely difficult to fully understand the performance and emissions characteristics of these engines [2, 3, 4, 5, 6 and 7]. Those engine parameters that are known to affect the gas flow and fuel injection processes of the PFI system include: port and valve configurations, combustion chamber shape, injector tip location, injection timing, spray cone angle and targeting, spray momentum and drop size. The overall performance of the engine is the net result of these complex interactions. Thus, capability to isolate individual parameter effects on engine performance is clearly needed for better PFI system design. Furthermore, there is current interest in engines that operate on alternate fuels such as methanol. The lower energy content per unit mass and higher latent heat of vaporization of methanol could add additional difficulties in applying alternate fuels to PFI engines. In particular, very different ignition requirements and/or delicate control of the combustion process may be needed as a result of its slow fuel evaporation.
In a previous study [8], General Motors Research Laboratories' (GMR) version of the multidimensional in-cylinder flow code, KIVA, was modified to calculate gas flow and fuel spray in an engine intake port. The code was further modified to conduct port-and-cylinder gas flow and fuel injection calculations in a generic port-fuel-injection engine with a moving valve [9]. The ability to make port-and-cylinder gas flow calculations with a moving valve is essential from a model validation standpoint. For instance, accurate assessment of various submodels is difficult if an assumed flow field is needed at intake valve closing to start the calculation. Furthermore, coupling the cylinder calculation with the valve/port calculation enables us to systematically examine parameters that are known to simultaneously affect the gas flow and fuel injection processes of the PFI engine.
Thus, the objective of this work was to apply the model for a generic port-fuel-injection engine to illustrate the detailed information and understanding the model can provide regarding gas flow, fuel spray, and combustion processes in the port and cylinder of the PFI engine during the intake, compression, and expansion strokes. A parametric study was also made with variations in port orientation, spray cone angle and valve configuration (without and with a 180-degree shroud) to further demonstrate the model's capability.
This paper is organized as follows. First, the port and cylinder geometries are described. Then, details are given of the flow, turbulence, valve, spray, ignition, and combustion submodels including the initial and boundary conditions. Finally, the results of three calculations with variations in port orientation, spray cone angle, and valve configuration are discussed which represent a parametric study of the model performance.
Recommended Content
Authors
Topic
Citation
Kuo, T., "Multidimensional Port-and-Cylinder Gas Flow, Fuel Spray, and Combustion Calculations for a Port-Fuel-Injection Engine," SAE Technical Paper 920515, 1992, https://doi.org/10.4271/920515.Also In
References
- World engines 1990 WARD Engine Update 1990
- Kosowski, M. G. “Soot Formation in a Multipoint-Fuel-Injected Spark-Ignited Engine,” SAE Trans. 94 789 796 1985
- Bandel, W. Fraidl, G. K. Mikulic, L. A. Quissek, F. Carstensen, H. “Investigation of Mixture Preparation and Charge Motion Effects on the Combustion of Fast-Burn Gasoline Engines,” SAE Paper No. 890160 1989
- Quader, A. A. “How Injector, Engine, and Fuel Variables Impact Smoke and Hydrocarbon Emissions with Port Fuel Injection,” SAE Paper No. 890623 1989
- Takemura, J. Sanbuyashi, D. Ando, H. “Effect of Turbulence in Intake Port of MPI Engine on Fuel Transport Phenomena and Nonuniformity of Fuel/Air Mixing in Cylinder,” SAE Paper No. 900162 1990
- Kadota, T. Mizutani, S. Wu, C.-Y. Hoshiro, M. “Fuel Droplet Size Measurements in the Combustion Chamber of a Motored SI Engine via Laser Mie Scattering,” SAE Paper No. 900477 1990
- Kadota, T. Zhao, F.-Q. Miyoshi, K. “Rayleigh Scattering Measurements of Transient Fuel Vapor Consentration in a Motored Spark Ignition Engine,” SAE Paper No. 900481 1990
- Kuo, Tang-Wei Chang, Shengming “Three-Dimensional Computations of Flow and Fuel Injection in an Engine Intake Port,” ASME Trans., Journal of Engineering for Gas Turbines and Power 113 3 427 432 1991
- Kuo, Tang“Wei “Three-Dimensional Port-and-Cylinder Gas Flow and Fuel-Injection Calculations for a Port-Fuel-Injection Engine,” Society of Engineering Science Preprint ESP28-91043 1991
- Amsden, A. A. Ramshaw, J. D. O'Rourke, P. J. Dukowicz, J. K. “KIVA: A Computer Program for Two-and Three-Dimensional Fluid Flows with Chemical Reactions and Fuel Sprays,” LA-10245-MS, Los Alamos National Laboratories February 1985
- Amsden, A. A. Ramshaw, J. D. Cloutman, L. D. O'Rourke, P. J. “Improvements and Extensions to the KIVA Computer Program,” LA-10534-MS, Los Alamos National Laboratories October 1985
- El Tahry, S. H. “The k-ϵ Equations in Compressible Flows,” Journal of Energy 7 4 345 353 1983
- Duggal, V. K. Kuo, Tang-Wei Mukerjee, T. Prezekwas, A. J. Singhal, A. K. “Three-Dimensional Modeling of In-Cylinder Processes in D.I. Diesel Engines,” SAE Trans. 93 30 43 1984
- O'Rourke, P. J. Amsden, A. A. “Three Dimensional Numerical Simulations of the UPS-292 Stratified Charge Engine,” SAE Trans. 96 Reciprocating engines - Spark Ignition and Diesel 710 727 1987
- Kuo, Tang-Wei Yu, R. C. “Modeling of Transient Evaporating Spray Mixing Processes - Effect of Injection Characteristics,” SAE Trans. 93 16 29 1984
- Reitz, R. D. “Modeling Atomization Processes in High-Pressure Vaporizing Sprays,” Atomization and Spray Technology 3 309 337 1988
- Naber, J. D. Reitz, R. D. “Modeling Engine Spray/Wall Impingement,” SAE Paper No. 880107 1988
- Najt, P. M. Kuo, Tang-Wei “An Experimental and Computational Evaluation of Two Dual-Intake-Valve Combustion Chambers,” SAE Paper No. 902140 1990
- Kuo, Tang-Wei Reitz, R. D. “Computation of Premixed-Charge Combustion in Pancake and Pent-Roof Engines,” SAE Paper No. 890670 1989
- Metghalchi, M. Keck, J. “Burning Velocities of Mixtures of Air with Methanol, Isooctane, and Indolene at High Pressure and Temperature,” Combustion and Flame 48 191 210 1982
- Kuo, Tang-Wei “What Causes Slower Flame Propagation in the Lean-Combustion Engine?” ASME Trans., Journal of Engineering for Gas Turbines and Power 112 3 348 356 1990
- Reitz, R. D. Kuo, Tang-Wei “Modeling of HC Emissions due to Crevice Flows in Premixed-Charge Engines,” SAE Paper No. 892085 1989
- Lienesch, J. H. “Engine Simulation Identifies Optimum Combustion Chamber Design,” Paper No. 80.4.4.7, 18th FISITA Congress 1980