This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
An Intake Charge Cooling System for Application to Diesel, Gasoline and Natural Gas Engines
Annotation ability available
Sector:
Language:
English
Abstract
Low intake manifold temperature, well below ambient, has many applications in internal combustion engines. In diesel engines, it can reduce NOx to a level of 2.0 g/hp-hr or below, going beyond the 1994 heavy duty diesel engine emissions standards. In gasoline engines, it can allow high compression ratio, turbocharged operation without end gas knock. This will permit ready conversion of some heavy duty diesel engines to gasoline operation at increased power density and lower emissions. In natural gas engines, it will allow base diesel engine to be converted to stoichiometric natural gas operation without increasing thermal loads. A three way catalyst can then be used to reduce emissions.
Recommended Content
Topic
Citation
Meyer, R. and Shahed, S., "An Intake Charge Cooling System for Application to Diesel, Gasoline and Natural Gas Engines," SAE Technical Paper 910420, 1991, https://doi.org/10.4271/910420.Also In
References
- Richards, R.R. Sibley J.E. “Diesel Engine Emissions Control for the 1990's,” SAE 880346
- Gill, Alan P. “Design Choices For 1990's Low Emission Diesel Engines,” SAE 880350
- Needham, J.R. May M.P. Doyle D.M. Faulkner S.A. Ishiwata H. “Injection Timing and Rate Control--A Solution for Low Emissions,” SAE 900854
- Shimada, Taizo Shoji Takeshi Takeda Yoshinaka “The Effect of Fuel Injection Pressure on Diesel Engine Performance,” SAE 891919
- Otani, Tetsuya Shigemori Masashi Suzuki Takayuki Shimoda Masatoshi “Effects of Fuel Injection Pressure and Fuel Properties on Particulate Emissions from H.D.D.I. Diesel Engine,” SAE 881255
- Kakegawa, T. Suzuki T. Tsujimura K. Shimoda M. “A Study on Combustion of High Pressure Fuel Injection for Direct Injection Diesel Engine,” SAE 880422
- Schulte, Horst Duernhholz Manfred Wuebbeke Kark “The Contribution of the Fuel Injection System to Meeting Future Demands on Truck Diesel Engines,” SAE 900822
- Arai, Minoru Miyashita Shoichiro “Particulate Regeneration Improvements on Actual Vehicle under Various Conditions,” SAE 900328
- Horiuchi, Makoto Saito Koichi Ichihara Shoichi “The Effects of Flow-through Type Oxidation Catalysts on the Particulate Reduction of 1990's Diesel Engines,” SAE 900600
- Shahed, S.M. Flynn P.F. Lyn W.T. “A Model for the Formation of Emissions in a Direct Injection Diesel Engine,” Combustion Modeling in Reciprocating Engines Aamann C.A. Mattavi J.N. Plenum Press 1970
- Shahed, S.M. “The Role of Fuel-Air Mixing in Diesel Combustion,” International Symposium on Flows in Internal Combustion Engines, ASME Winter Annual Meeting
- Yu, R.C. Shahed, S.M. “Effects of Injection Timing and Exhaust Gas Recirculation on Emissions from a D.I. Diesel Engine,” SAE 811234
- Kato. T. Tsujimura K. Shintani M. Minami T. Yamaguchi I. “Spray Characteristics and Combustion Improvement of D.I. Diesel Engine with High Pressure Fuel Injection,” SAE 890265
- Minami, T. Yamaguchi I. Shintani M. Tsujimura K. Suzuki T. “Analysis of Fuel Spray Characteristics and Combustion Phenomena under High Pressure Fuel Injection,” SAE 900438
- Douad, A.M. Eyzat, P. “Four-Octane Number Method for Predicting Anti-Knock Behaviour of Fuels,” SAE 780080
- Taylor, C.F. The Internal Combustion Engine in Theory and Practice Volume I: Thermodynamics, Fluid Flow, Performance MIT Press 1979
- Pitz, W.J. Westbrook, C.K. “Chemical Kinetics of High Pressure Oxidation of n-Butane and its Relationship to Engine Knock” Combustion & Flame 63 113 133 1986
- Pitz, W.J. Westbrook, C.K. Leppard, W.R. “Autoignition Chemistry of n-Butane in a Motored Engine: A Comparison of Experimental and Modeling Results” SAE 881605
- Beck, N.J. “Natural Gas - A Rational Approach to Clean Air,” SAE 902228
- Helmich, M.J. “Development of Combustion Air Refrigeration System Enabling Reliable Operation at 220 psi bmep for a Large Four-Cycle Spark-Ignited Gas Engine,” ASME 66-DGEP-7