This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Development of a New Optical Technique for Measuring Diesel Spray Penetration
Annotation ability available
Sector:
Language:
English
Abstract
A new optical measuring technique of tip penetration of a diesel fuel spray was developed by detecting the arrival times of the spray tip at several light sheets which were preset at various axial locations downstream. Verified by the instantaneous photographic technique, it was confirmed that this technique is effective, with sufficient accuracy, for measuring the spray tip penetration much more easily than the conventional photographic technique. The tip penetrations of diesel sprays injected through single-hole nozzles with various orifice lengths and diameters has been investigated over a wide range of the operating conditions by this technique. The spray injected through two multihole nozzles, either with or without a sac volume, has also been characterized. The results showed that the spray tip penetration is affected somewhat by the operating conditions. Eventually it is affected by the injected fuel momentum flowrate, nozzle geometry and ambient gas density.
Recommended Content
Citation
Xu, M. and Hiroyasu, H., "Development of a New Optical Technique for Measuring Diesel Spray Penetration," SAE Technical Paper 902077, 1990, https://doi.org/10.4271/902077.Also In
References
- Schweitzer P.H. “Penetration of Oil Sprays” Pennsylvania State College Bulletin 1937
- Wakuri Y. Fujii M. Amitani T. Tsuneya R. “Studies of the Penetration of a Fuel Spray in a Diesel Engine” Bull. JSME 3 9 1960
- Dent J.C. “A Basis for the Comparison of Various Experimental Methods for Studying Penetration” SAE paper, No. 710571 1971
- Hay N. Jones P.L. “Comparison of the Various Correlations for Spray Penetration” SAE paper. No. 720776 1972
- Hiroyasu H. Arai M. “Structure of Fuel Sprays in Diesel Engines” SAE paper, No. 900475 1990
- Reitz R.D. Bracco F.B. “On the Dependence of Spray Angle and Other Spray Parameters on Nozzle Design and Operating Conditions” SAE paper, No. 790494 1979
- Varde K.S. Popa D.M. “Diesel Fuel Spray Penetration at High injection Pressures” SAE paper, No. 830448 1983
- Hiroyasu H. Arai M. “Fuel Spray Penetration and Spray Angle in Diesel Engines” Trans.JSME 34 385 1978 3208
- Yule A.L. Mo S.-L. Tham S.Y. Aral S.M. “Diesel Spray Structure” ICLASS-85, Paper IIB/2/1 1985
- Arcoumanis C. Cossali E. Paal G. Whitelaw J.H. “Transient Characteristics of Single-Hole Diesel Sprays” SAE paper, No. 890314 1989
- Matsuoka S. Yokota K. Kamimoto T. Igoshi M. Yamada H. “A Study on Fuel Injection System in Diesel Engine (Part 1)” Tran.JSME 40 332 1974 1130
- Kuniyoshi H. Tanabe H. Sato G.T. Fujimoto H. “Investigation on the Characteristics of Diesel Fuel Spray” SAE paper, No. 800968 1980
- Ha J.Y. Hayashi A. Tanabe N. Kuniyoshi H. Sato G.T. Fujimoto H. “Investigation on the Initial Part and the Spray Formation Delay of Diesel Spray” SAE paper, No. 830451 1983
- Shimizu M. Arai M. Hiroyasu H. “The Measurements of Breakup Length in High Speed Jet” Trans.JSME 49 448 1983 2890
- Arcoumanis C. Cossali E. Paal G. Whitelaw J.H. “Transient Characteristics of Multi-Hole Diesel Sprays” SAE paper, No. 900480 1990
- Andoh H. Shiraishi K. “Influence on Injection and Combustion Phenomena by Elimination of Hole Nozzle Sac Volume” SAE paper, No. 860416 1986
- Greeves G. Khan I.M. Wang C.H.T. Fenne I. “Origins of Hydrocarbon Emissions from Diesel Engines” SAE paper, No. 770259 1977