This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
The In-Service Braking Levels of Australian Heavy Vehicles
Annotation ability available
Sector:
Language:
English
Abstract
A lack of knowledge of driver behaviour and vehicle performance at everyday braking levels has made it difficult to develop Australian Design Rules which achieve a balance of braking between heavy vehicle tractors and trailers under all operating conditions. This paper examines the in-service braking behaviour of heavy vehicle drivers to provide information for use in the development of design rules, which would improve tractor/trailer braking compatibility under routine braking regimes. Results show that while braking is required every 500 m under heavily trafficked urban driving conditions, on roads with high levels of service this can reduce to once every 11 km on average. Under the right road and traffic conditions, heavy vehicles were shown to travel up to 90 kms between brakings. Average braking duration was between 6 and 9 seconds with average deceleration rates of between 0.4 and 0.7 m/s2. These decelerations are considerably less than the 0.25 g accepted as the limit of comfortable passenger car braking, as well as those within which the current Australian Design Rules for truck braking are framed. The average speed change during braking was found to be small for all road types considered, with very few brakings made from very high to low speeds. The constant adjustment of speed to the conditions by drivers appears to pre-empt the need for severe braking. The majority of pedal pressures were found to be below 100 kPa and the rate of pressure rise was modest compared with expectations. Less than 1% of brakings showed the driver to be modulating his braking during the deceleration. The profile of normal braking behaviour developed by the research has allowed recomendations to be made for changes to the Australian Design Rules for heavy vehicle braking and these are currently under industry review.
Recommended Content
Authors
Topic
Citation
Jarvis, J., "The In-Service Braking Levels of Australian Heavy Vehicles," SAE Technical Paper 892505, 1989, https://doi.org/10.4271/892505.Also In
References
- JARVIS J.R. “The nature of braking behaviour”. ARRB Internal Report AIR 453-1. Australian Road Research Board 1988
- TIGNOR S.C. “Braking performance of motor vehicles” Public Roads 34 4 1966
- SAMUELS S.E. JARVIS J.R. “Acceleration and deceleration of modern vehicles”. ARRB Research Report ARR No. 86, Australian Road Research Board 1978
- WILSON E.E. “Deceleration distances for high speed vehicles” Proc. H.R.B. Vol 2 1940
- WORTMAN R.M. MATTHIAS J.S. “Evaluation of driver behaviour at signalised intersections”. Trans. Res. Record No. 954 10 16. Washington 1983
- MORTIMER R.G. SEGAL L. DUGOFF H. CAMPBELL J.D. JORGENSON CM. MURPHY R.W. “Brake force requirement study: Driver-vehicle braking performance as a function of brake system design variables”. Report No. HuF-6, Highway Safety Research Institute, University of Michigan 1970
- MacKAY J.G. “Vehicle braking task report”. Heavy commercial vehicle speed and operational safety study. Road Safety and Traffic Authority. Melbourne 1978
- THOMPSON W.T. “Vehicle speeds task force” Heavy commercial vehicle speed and operational safety study. Road Safety and Traffic Authority Melbourne 1978
- HORSHAM A. “Certification Testing”. Seminar on Braking. Soc. of Auto, Eng. Aust. Melbourne 1980
- RADLINSKl R.W. FLICK M.A. “Tractor and Trailer Brake System Compatibility” SAE Technical Paper Series No. 861942 , Warrendale 1988
- FROOD A.D.M. MacKENZIE D.K. NEWCOMB T.P. “Brake usage in a heavy vehicle”. Proc. Auto. Div. Inst, of Mech. Eng. pp 351 358 1960
- NEWCOMB T.P. SPURR R.T. “Braking of road vehicles”. Chapman and Hall Ltd. London 1967
- JARVIS J.R. “In-service vehicle decelerations”. ARRB Project 281, working papers. Australian Road Research Board 1985
- GLYNN L. “Optimising truck and trailer brake compatibility: A study of cause and effect” Trucks and Trailers Seminar, Soc. Auto. Eng. Aust. Melbourne 1988
- FRASER P.J. “The ARRB Vehicle Detector Data Acquisition System (VDDAS)” ARRB Technical Manual ATM No. 12, Australian Road Research Board 1981
- GLYNN L. “Developing truck-trailer brake compatibility standards”. Third International Heavy Vehicle Seminar, Inst. Rd. Transp. Eng. Christchurch, New Zealand 1989