This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Constrained Adjustment of Analytical Stiffness Matrices
Annotation ability available
Sector:
Language:
English
Abstract
A procedure is described that can use mode data, static test data, and structural geometry information to optimally adjust deficient stiffness matrices. The adjustments can be performed subject to weighting of individual stiffness coefficients, and the physical configuration of the analytical model is preserved. In addition, the adjustments can be performed such that the adjusted model will reproduce the modes used in the identification. The theoretical development is presented, and the procedure is demonstrated by numerical simulation of several test problems. Furthermore, the procedure's sensitivity to noise in measured mode data is studied.
Recommended Content
Citation
Kabe, A., "Constrained Adjustment of Analytical Stiffness Matrices," SAE Technical Paper 851932, 1985, https://doi.org/10.4271/851932.Also In
References
- Fleming, E. R. “The Use of Component Mode Synthesis in the Dynamic Analysis of Aerospace Systems,” Combined Experimental/ Analytical Modeling of Dynamic Structural Systems, AMD 67 Joint ASCE/ASME Mechanics Conference Albuquerque, NM 24-26 June 1985
- McGrew, J. “Orthogonalization of Measured Modes and Calculation of Influence Coefficients,” AIAA J. 7 7 April 1969 774 776
- Rodden, W. P. “A Method for Deriving Structural Influence Coefficients from Ground Vibration Tests,” AIAA J. 5 5 May 1967 991 1000
- Hall, B. M. “Linear Estimation of Structural Parameters from Dynamic Test Data,” AIAA/ASME 11TH Structures, Structural Dynamics, and Materials Conference Denver, CO 22-24 April 1970
- Berman, A. Flannelly W. G. “Theory of Incomplete Models of Dynamic Structures,” AIAA J. 9 8 August 1971 1481 1487
- Ross, R. G., Jr. “Synthesis of Stiffness and Mass Matrices from Experimental Vibration Modes,” SAE paper 710787 Sept. 1971
- Zak, M. “Discrete Model Improvement by Eigenvector Updating,” ASCE J. of Engineering Mechanics 109 6 December 1983 1437 1444
- Collins, J. D. et al. “Statistical Identification of Structures,” AIAA J. 12 2 February 1974 185 190
- Lee, L. T. Hasselman T. K. “Dynamic Model Verification of Large Structural Systems,” SAE paper 781047 November 1978
- Chen, J. C. Wada B. K. “Criteria for Analyses-Test Correlation of Structural Dynamic Systems,” J. of Applied Mechanics June 1975
- Chen, J. C. Garba J. A. “Analytical Model Improvement Using Modal Test Results,” AIAA J. 18 6 June 1980 684 690
- Baruch, M. “Optimal Weighted Orthogonalization of Measured Modes,” AIAA J. 16 4 April 1978 346 351
- Baruch, M. “Optimization Procedure to Correct Stiffness and Flexibility Matrices Using Vibration Tests,” AIAA J. 16 11 November 1978 1208 1210
- Berman, A. “Mass Matrix Correction Using an Incomplete Set of Measured Modes,” AIAA J. 17 10 October 1979 1147 1148
- Berman, A. Nagy E. J. “Improvement of a Large Analytical Model Using Test Data,” AIAA J. 21 8 August 1983 1168 1173
- Kabe, A. M. “Stiffness Matrix Adjustment Using Mode Data,” AIAA J. Fall 1985
- Kabe, A. M. “Constrained Stiffness Matrix Adjustment Using Mode Data,” Report No. TR-0084(4409-13)-1 The Aerospace Corporation El Segundo, CA 15 August 1984
- Hadley, G. Nonlinear and Dynamic Programming Addison-Wesley Publishing Company, Inc. Reading, MA 1964
- Targoff, W. P. “Orthogonality Check and Correction of Measured Modes,” AIAA J. 14 2 February 1976 164 167