This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Two-Dimensional Combustion Chamber Analysis of Direct Injection Diesel
Annotation ability available
Sector:
Language:
English
Abstract
Re-entrant bowls for high compression ratio heavy-duty turbocharged DI Diesel have been studied by the utilization of a two-dimensional axisymmetric model of the air motion and spray formation inside the cylinder. The trend of the air motion and spray pattern obtained by changing combustion chamber parameters are compared with the trend of the engine performance like smoke, fuel consumption, gaseous emissions and heat release rate. The results of this study strongly support the hypothesis that with reentrant-shaped combustion chambers an optimum level of the air fuel mixing is achieved at low values of the inlet port generated swirl.
Recommended Content
Authors
Citation
Bassoli, C., Biaggini, G., Bodritti, G., and Cornetti, G., "Two-Dimensional Combustion Chamber Analysis of Direct Injection Diesel," SAE Technical Paper 840228, 1984, https://doi.org/10.4271/840228.Also In
References
- Cartellieri W. Johns R.J.R. “Multidimensional Modelling of Engine Processes: Progress and Prospects” Cimac Congress Paris June 1983
- Dent J.C. Metha P.S. Swan J. “A Predictive Model for Automotive D.I. Diesel Engine Performance and Smoke Emissions” Paper C126\82 presented at the Institution of Mechanical Engineers Symposium on ‘Diesel engines for passenger cars and light-duty vehicles‘ London 5\7 October 1982
- Cloutman L.D. Dukowicz J.K. Ramshaw J. D. Amsden A.A. “Conchas-Spray: A Computer Code for Reactive Flows with Fuel Sprays” Report LA-9294-MS UC-32 Los Alamos National Laboratory May 1982
- Cichocki R. Cartellieri W. “The Passenger Car Direct Injection Diesel-A Performance and Emission Update” SAE paper No. 810480
- Basshuysen R. Stock D. Weber R.J. “Development of Direct-Injection Diesel Engines for VW Golf” MTZ 41 1980 7\8 289 295
- Middlemiss I.D. “Characteristics of the Perkins ‘Squish Lip’ Direct Injection Combustion System” SAE paper No. 780113
- Goodwin C. “Emission Control of Turbocharged Diesel Truck Engines with the Perkins ‘Squish Lip’ Combustion System” MTZ 41 1980 2 51 56
- Bassoli C. Bodritti G. Cornetti G.M. “Combustion Chambers for High Compression Ratio D.I. Diesel” Paper 345038 to be presented at XX FISITA Congress Vienna May 8 1984
- El Tahry S.H. “A Numerical Study on the Effects of Fluid Motion at Inlet-Valve Closure on Subsequent Fluid Motion in a Motored Engine” SAE paper N. 820035
- Bodritti G. “A Theoretical and Experimental Study of the Compression Ignition in Diesel Engines” Degree thesis Turin Politecnico December 1982
- Hiroyasu H. Arai M. Nakanishi K. “ Soot Formation and Oxidation in Diesel Engines” SAE paper No. 800252 from SAE Proceedings P-86 February 1980 205 218
- Mitteregger R. “ Swirl Characteristics of the 8060 Iveco Engine Ports” Dereco internal report November 1983 Arbon (Switzerland)
- Witze P.O. “Comparison between Measurement and Analysis of Fluid Motion in Internal Combustion Engines” Report SAND81-8242 Sandia National Laboratories October 1981
- Arcoumanis C. Bicen A.F. Whitelaw J.H. “Squish and Swirl-Squish Interaction in Motored Model Engines” Journal of Fluids Engineering, Transactions of the ASHE March 1983 105
- Vafidis C. “Influence of Induction Swirl and Piston Configuration on Air Flow in a Four-Stroke Model Engine” Proceedings of the Institution of Mechanical Engineers, Part C February 1984
- Dominici A. “Swirl Velocity Profile of the 8060 Iveco Engine Intake Port by means of a 3-D Pitot” Fiat Research Center internal report November 1983
- Hoult D.P. Wong V.W. “The Generation of Turbulence in an Internal Combustion Engine” From the G.M. symposium’ Combustion modeling in reciprocating engines’ Mattavi J.N. Amann C.A. 131 Plenum Press 1980
- Harvey P.S. Gosman A D. “An Analysis of the Influence of Swirl on Combustion in D.I. Diesel Engines by Computer Simulation” Paper C130\82 presented at the Institution of Mechanical Engineers Symposium on ‘Diesel engines for passenger cars and light-duty vehicles’ London 5\7 October 1982
- Liou T.M. “Laser Doppler Velo-cimetry Measurements in Valved and Ported Engines” Ph.D. thesis, Princeton University May 1983
- Belardini P. Bertoli C. Corcione F.E. Police G. Valentino G. “The Air Flow Field by LDA under Steady-State: the Influence of Vortex Structure on the Performance of a D.I. Diesel” ATA (Italian Automotive Technical Association) Congress October 5\7 1983
- Bracco F.V. “Atomization and Sprays”.Lecture during the ‘Short course on optical diagnostics in internal-combustion engines’ Sandia National Laboratories June 8\11 1982
- O'Rourke P.J. “Collective Drop Effects on Vaporizing Liquid Sprays” Ph.D. thesis, Princeton University August 1981
- Basso A. “Multi-dimensional modeling of the air motion” Fiat Research Center internal report December 1983
- Bertero L. “Fluidynamics of an Axisymmetric Combustion Chamber for Diesel Engines” Degree thesis Turin Politecnico March 1984
- Luciani P.F. “Interactions between the Air Motion and the Fuel Jet in a Combustion Chamber of a Diesel Engine” Degree thesis Turin Politecnico July 1984