This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Characteristics of Primed Methanol Fuels for Passenger Cars
Annotation ability available
Sector:
Language:
English
Abstract
In addition to the use of volatile primers to provide methanol fuels with good cold starting characteristics, an additional component is needed for luminosity of methanol flames. Methanol fuels have been prepared with several volatile primers to provide improved cold starting characteristics. Dimethyl ether, which can be readily made from methanol, appears to be superior in several respects to other primers because it imparts adequate volatility at reasonably low concentrations and can tolerate water contamination without volatility changes or phase separation better than hydrocarbon primers. Hydrocarbon components have been identified that provide adequate luminosity to methanol fuel flames. Estimates of vapor flammability indicate that dimethyl ether primed methanol fuels can be made whose vapor is too rich to burn in confined tankage at least down to −20°C. The upper flammability temperature of isopentane primed methanol can be close to that of gasoline (−30°C), but the isopentane solutions are sensitive to water contamination. Primed methanol experiences greater volatility loss than gasoline during storage and use in vehicle tanks and carburetors. Greater evaporative emissions were also observed. Primers in the concentration range 0-15 volume percent appear to have no effect on octane quality in the CFR engine. Dimethyl ether seems not to aggravate methanol's preignition tendency.
Authors
Citation
Panzer, J., "Characteristics of Primed Methanol Fuels for Passenger Cars," SAE Technical Paper 831687, 1983, https://doi.org/10.4271/831687.Also In
References
- Keller J. L. Nakaguchi G. M. Ware J. C. Wiseman E. L. “Methanol Fuel Modification for Highway Vehicle Use, Final Report,” HCP/W 3683-18; July 1978
- Ingamells J. C. Lindquist R. H. “Methanol as a Motor Fuel or Gasoline Blending Component,” SAE Paper 750123 February 1975
- Reglitzky A. A. Hooks R. W. Bernhardt W. E. “Alternative Fuels for Existing Engines, Their Potential, and Drawbacks,” Tenth World Petroleum Congress September 1979
- Ito S. Sato S. Ichimiya T. “Performance of a Methanol Fueled Car,” International Pacific Conference on Automotive Engineering, Honolulu, Proceedings P 98 109 811383 November 1981
- Tillman R. M. “Blending, Distribution, and Marketing Aspects of Alcohols as Alternative Fuels,” Symposium on Alcohols as Alternative Fuels for Ontario November 19 1976
- Koenig A. Menrad H. Bernhardt W. E. “Alcohol Fuels in Automobiles,” Alcohol Fuel Conference Sydney August 1978
- Mottlau A. Y. “Rapid, Precise Micro Vapor Pressure Method,” Analytical Chemistry 29 1196 August 1957
- Perry R. H. Chilton C. H. Kirkpatrick S. K. Perry's Chemical Engineers Handbook 4th edition McGraw Hill, New York 1963
- Bernstein L. S. Panzer J. “Priming Agents for Methanol as an Automotive Fuel,” Proc. Fifth International Alcohol Fuels Symposium Auckland May 1982
- Anderson J. E. Siegl W. O. “Use of Co-Fuels to Increase the Luminosity of Methanol Pool Fires: Some Preliminary Findings,” ACS Div. of Petroleum Chemistry Kansas City September 1982
- Gordon A. J. Ford R. A. The Chemists Companion John Wiley New York 1972
- “On the Trail of New Fuels - Alternative Fuels for Motor Vehicles,” UCRL Translation 10879 May-June 1975
- Kierhawe B. “Methanol Gasoline Blended Fuels in West Germany - Specification and Early Experience,” Proc. Fourth International Symposium on Alcohol Fuels Technology Guaraja October 1980 319
- Anderson J. E. Nichols R. J. “Fuel Methanol Additives: Issues and Concerns,” Proc. Tenth Energy Technology Conference Washington, DC February 1983
- Murin J. M. Weller A. E. “Prediction of the Ignition Limits of Alcohol-Hydrocarbon Mixtures,” Central States Section of Combustion Inst. March 21 1983
- Coward H. E. Jones G. W. “Limits of Flammability of Gases and Vapors,” Bureau of Mines Bulletin 503 1976
- Hunwartzen I. “Modification of CFR Test Engine Unit to Determine Octane Numbers of Pure Alcohols and Gasoline Alcohol Blends,” SAE Paper 820002 February 1982
- Starke K. “Fueling the Spark Ignition Engine with Gasoline-Methanol,” International Symposium on Alcohol Fuel Technology Wolfsburg November 1977
- Menrad H. Haselhorst M. Ewig W. “Preignition and Knock Behavior of Alcohol Fuels,” SAE Paper 821210 Toronto October 1982
- Most W. J. Longwell J. P. “Single-Cylinder Engine Evaluation of Methanol-Improved Energy Economy and Reduced NO X ,” SAE Paper 750119 February 1975
- Penzig F. “On the Behavior of Spark Plugs Using Methanol as Fuel,” IG Farben Report 294 September 2 1935
- Penzig F. “Methanol as an Engine Fuel,” IG Farben Report 557 January 3 1944
- Menrad H. “A Motor Vehicle Powerplant for Ethanol and Methanol Operation,” Third International Symposium on Alcohol Fuels Technology,” Asilomar, Paper II-26 May 1979
- Loeck H. Menrad H. “Combustion Behavior of Alcohol Fuels,” International Symposium on Knocking of Combustion Engines November 1981
- Winch R. F. Mayes F. M. “A Method for Identifying Preignition,” SAE Transactions 61 453 1953
- Beesch O. “Classification and Selection of the Heat Ranges of Spark Plugs for International Combustion Engines,” Bosch Technische Berichte 4 1 47 1972