This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Study of Combustion Chamber Arrangements and Heat Release in D.I. Diesel Engines
Annotation ability available
Sector:
Language:
English
Abstract
The experimental and analytical results from a study of a single cylinder di diesel with various combustion chamber arrangements are presented. The study investigates the properties of toroidal and cylindrical piston cavities with different fuel spray paths.
It is shown that seemingly similar combustion arrangements behave differently. One system (optimized cylindrical) demonstrates an improved thermal efficiency and reduced sensitivity to changes in injection timing.
Heat release data computed from p-θ diagram over a wide range of power, speed, and injection timing is presented. From this data, a method of calculating heat release curves for cycle synthesis is identified. The method is based on the summation of two “Wiebe” type curves. Results show good correlation between experimental and calculated cycle parameters for the systems tested.
Authors
Topic
Citation
Ghojel, J., "A Study of Combustion Chamber Arrangements and Heat Release in D.I. Diesel Engines," SAE Technical Paper 821034, 1982, https://doi.org/10.4271/821034.Also In
References
- Monaghan, M. L. “The High Speed Direct Injection Diesel for Passenger Cars,” SAE Paper 810477
- Elsbett, L. Behrens, M. “Elko’s Light Duty D. I. Diesel Engine with Heat Insulated Combustion System and Component Design,” SAE Paper 810478
- Neitz, A. D’Alfonso, N. “The M.A.N. Combustion System with Controlled Direct Injection for Passenger Car Diesel Engines,” SAE Paper 810479
- Cichoski, R. Cartellieri, W. “The Passenger Car Direct Injection Diesel - A Performance and Emission Update,” SAE Paper 810480
- Hardenberg Horst Wagner Wilhelm “Der Zundverzug in direk-teinspiritzender Dieselmotoren,” MTZ 1971 7
- Austen, A.E.W. Lyn, W. T. “Relation Between Fuel Injection and Heat Release in Direct Injection Diesel Engines, and the Nature of the Combustion Processes,” Proc. Aut. Div. Instn. Mech. Engrs 1960–61 No. 1
- Lyn, W. T. “Calculations of the Effect of Rate of Heat Release on the Shape of Cylinder Pressure Diagrams and Cycle Efficiency,” Proc. Aut. Div. Inst. Mech. Engrs No. 1 1960–61
- Zinner Karl “Einige Ergebrisse realer Kreisprozessrechnungen uber die Beeinflussungsmoglichkeiten des Wirkungs-grades Von Dieselmotoren,” MTZ, T 31 6 1970
- Wiebe I. I. “Novoye o rabocheim tciklye dveegatelieye” Mashgiz, 1962 “New Information about the Working Cycle of Engines.”
- Naboru Miyamoto et al. “Studies on Low Compression Ratio Diesel Engines - 3rd Report: Relation Between Combustibility and Performance,” Bull. JSME 15 No. 90 1972
- Woschni, G. Anisits, F. “Experimental Investigation and Mathematical Presentation of Rate of Heat Release in Diesel Engines Dependent Upon Engine Operating Conditions,” SAE Paper 740086
- Whitehouse, N. D. Way, R. J. B. “A Simple Method for the Calculation of Heat Release Rates in Diesel Engines Based on Fuel Injection Rate,” SAE Paper 710134
- Grigg, H. C. Syed, M. H. “The Problems of Predicting Rate of Heat Release in Diesel Engines,” Proc. Instu. Mech. Engrs 184 (Pt. 35) 1969–70
- Megeuerdichian, M. Watson, N. “Prediction of Mixture Formation and Heat Release in Diesel Engines,” SAE Paper 780225
- Dichenko, N. X. Magidovich, L. E. Pougachov, B. P. “Ob Approximatsiye Kharacteristic Teplovideliyniye v Diezeliakh,” Energomashinostroiyeniye 1969
- Dichenko, N. X. Magedovich, L. E. Pougachov, B. P. “Opredeliyniye Osnovnikh Parametrov Kharacteristic Teplovideliyniye pri Sgoraniye v Dieseliy,” Troudi LPI 316 1970
- Watson, N. Pilley, A. D. Marzouk, M. “A Combustion Correlation for Diesel Engine Simulation,” SAE Paper 800029