This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Hydrocarbon Oxidation in the Exhaust Port of a Spark Ignition Engine
Annotation ability available
Sector:
Language:
English
Abstract
An experimental study was performed to determine the fraction of unburned hydrocarbon emissions which are oxidized in the exhaust port of a spark ignition engine. The technique used was injection of a CO2 quench gas into the exhaust port, at various planes along the port centerline, to cool the exhaust gas and “freeze” the hydrocarbon oxidation reactions. By quenching the reaction of hydrocarbons at the cylinder exit plane, cylinder exit hydrocarbon emissions levels were determined. By differencing the concentration of hydrocarbons observed during quenching and nonquenching operation, the fraction of hydrocarbons reacting in each section of the exhaust was determined.
Experiments were carried out to define the effects of engine operating conditions on the fraction of hydrocarbons oxidized. The variables studied were fuel-air equivalence ratio, speed, load, spark advance and compression ratio. The results of the experimental parametric study were correlated with those predicted by an existing exhaust port oxidation model.
The results show that reductions in hydrocarbon level due to oxidation in the exhaust port range between 2 and 37%. Those variables that cause substantial changes in gas temperature, port residence time, or oxygen concentration were most significant. Cylinder exit hydrocarbon emissions levels and the extent of reaction within the exhaust port for a range of fuel composition were also determined.
A set of experiments with air injection into the exhaust, at the cylinder exit plane, showed that substantial additional oxidation of hydrocarbons can be obtained with injection into the exhaust gases before significant cooling occurs.
Recommended Content
Authors
Citation
Mendillo, J. and Heywood, J., "Hydrocarbon Oxidation in the Exhaust Port of a Spark Ignition Engine," SAE Technical Paper 810019, 1981, https://doi.org/10.4271/810019.Also In
References
- Lavoie G. A. LoRusso J. A. Adamczyk A. A. “Hydrocarbon Emissions Modeling for Spark Ignition Engines,” Combustion Modeling in Reciprocating Engines: Proceedings of Symposium at GM Research Laboratories November 1978 Mattavi J. N. Amann C. A. 409 440 Plenum Press 1980
- Kummer J. T. “Catalysts for Automobile Emission Control” Progr. Energy Combustion Sci. 6 177 199 1980
- Lang R. J. “A Well-Mixed Thermal Reactor System for Automotive Emission Control,” SAE Paper 710608 June 1971
- Lord H. A. Sondreal E. A. Kadlec R. H. Patterson D. J. “Reactor Studies for Exhaust Oxidation Rates,” SAE Paper 730203 January 1973
- Herrin R. J. Patterson D. J. Kadlec R. H. “Modelling Hydrocarbon Disappearance in Reciprocating-Engine Exhaust,” Combustion Modelling in Reciprocating Engines: Proceedings of Symposium at GM Research Laboratories November 1978 Mattavi J. N. Amann C. A. 447 476 Plenum Press 1980
- Caton J. A. Keywood J. B. “Models for Heat Transfer, Mixing and Hydrocarbon Oxidation in an Exhaust Port of a Spark-Ignited Engine,” SAE Paper 800290 1980
- Heywood J. B. Higgins J. N. Watts P. A. Tabaczynski R. J. “Development and Use of a Cycle Simulation to Predict SI Engine Efficiency and NO x Emissions,” SAE Paper 790291 February 1980
- Bascunana J. L. Skibinski J. Weaver E. E. “Rates of Exhaust Gas-Air Reactions,” SAE Paper 770639 June 1977
- Mendillo J. V. “Quenching Studies to Determine Hydrocarbon Oxidation in the Exhaust Port of a Spark Ignition Engine,” M.S. Thesis, Dept. of Mech. Eng., M.I.T. February 1980
- Harrington J. A. Shishu R. C. “A Single-Cylinder Engine Study of the Effects of Fuel Type, Fuel Stoichiometry, and Hydrogen-to-Carbon Ratio on CO, NO, and HC Exhaust Emissions,” SAE Paper 730476 May 1973