This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Troubles and Countermeasures on Oil Seals for Automotive Application
Annotation ability available
Sector:
Language:
English
Abstract
In order to improve the reliability of oil seals in practical use, it is considered that further basic investigation for maintaining good sealing characteristics of seals are necessary. However, the result of analysing phenomena in oil seals which has caused the oil leakage in the market shows that about 60 % of oil leakage is caused by the seal installation to housing bore or shaft, about 30 % thereof by unsuitable operating condition and remaining 10 % by the design of oil seals.
From the point, oil leakage troubles and their countermeasures on oil seals for automotive application are discussed.
Recommended Content
Technical Paper | Sealing Reliability System on Oil Seals |
Technical Paper | Laminar Sealing Rings for Rotating Shafts and Housings |
Technical Paper | A Study on the Surface Temperature of Rotary Lip Seals |
Authors
Topic
Citation
Hirabayashi, H., Ohtaki, M., Tanoue, H., and Matsushima, A., "Troubles and Countermeasures on Oil Seals for Automotive Application," SAE Technical Paper 790346, 1979, https://doi.org/10.4271/790346.Also In
References
- Jagger E. T. “Lip-type rubber seals for rotary shafts. A review of recent literature” Second Review and bibliography on aspect of fluid sealing, Paper B BHRA Fluid Engineering 1975 43 74
- Hirabayashi H. “A recent status of sealing devices” Science of Machine 27 1 1975 192 198
- Jagger E. T. Walkner P. S. “Further studies of lubrication of synthetic rubber rotary shaft seals” Proceedings of the Institute of Mechanical Engineers 181 1966-67 6 16
- Hirano F. Ishiwata H. “The lubricating condition of a lip seal” Proceeding of the Institute of Mechanical Engineers 180 1965-66 138 147
- Shimotsuma Y. Iwasaki M. “Study on positive contact seals - Sealing mechanisum of lip-type oil seals -” Junkatsu(JSLE) 21 2 1976 164 170
- Schnurle F. Upper G. “Influence of hydrodynamics on the performance of radial lip seals” ASLE, Paper No. 73AM-9B-2 1973 1 6
- Kawahara Y. Hirabayashi H. “A study of sealing phenomena on oil seals” ASLE, Paper No. 77-LC-5B-2 1977 1 8
- Kawahara Y. Abe M. Hirabayashi H. Matsushima A. “Effect of surface condition of lip on sealing phenomena of oil seals” SAE Paper No. 780405 1978 1 10
- Kawahara Y. Abe M. Hirabayashi H. “An analysis of sealing characteristics of oil seals” ASLE, Paper No. 78-LC-2B-1 1978 1 10
- Brink B. V. “The heat lead of an oil seal” Proceeding of 6th Inter. Conf. on Fluid Sealing Paper No. C1 1973 1 10
- Ohara S. “On the threaded lip seals made by synthetic rubber” Junkatsu( JSLE) 14 5 1969 240 244
- Symons J. D. “Seal size-its effects on radial lip-type oil seal design” SAE Paper No. 780400 1978 1 9
- Symons J. D. “The shaft and radial lip seal performance” Proceedings of the SME Inter. Conf. on Surface Technology Paper No. IQ73-640 1976 584 605
- Horve L. “How to select radial lip seals” Power Transmission Digest 11 1974 48 50
- Hirabayashi H. Yukimasa T. Uchino K. “Effect of quantity of lubricating oil on sealing characteristics of oil seals” SAE Paper No. 78406 1978 1 14
- Hirabayashi H. Yukimasa T. Uchino K. “Effect of foreign matters on sealing characteristics of oil seals” SAE Paper No. 770175 1977 1 12
- Griffiths A. Taylor R. R. “The effect of lubricants on synthetic rubbers in rotary shaft seal design” Proceedings of the Institute of Mechanical Engineers 184 31 1969-70 1 8
- Austin R. M. “Rotary-shaft lip seals” BHRA Technical Report 1 9
- Austin R. M. Nau B. S. “The Seal Users Handbook, 6.4-Rotary shaft lip seal failure modes” BHRA 1977 83
- Berens A. S. “Rubber and lubricant compatibility” SAE Paper No. 740203 1974 1 8