This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Head Space Requirements for Seat Belt Wearers
Annotation ability available
Sector:
Language:
English
Abstract
Investigations in New South Wales of passenger car crashes involving the death of wearers of lap/sash belts have led to the conclusion that head impact with a rigid part (usually in the side) of the occupied car is responsible for more deaths than any other impact.
The experimental work reported in this paper consists of crash simulations to map the space swept by the head of a lap/sash belted occupant, in head-on and in a range of side impacts in which no invasion or loss of head space occurs. The simulations employed an Ogle-MIRA dummy which has a very compliant thorax, modified with the stacked ball joint neck from a Sierra 1050 dummy, this combination having been shown to closely reproduce head motion of human volunteers in frontal crashes reported in the literature. The work includes validation of the dummy and an investigation of the influence on head space of the angle of crash, of inertia reels in the sash straps, and of seat springing, in contrast to the hard seats used for the volunteer crashes. The results provide evidence of the value of increasing head space so as to reduce the likelihood of head impact of otherwise well restrained occupants of passenger cars.
Three current model cars are tested for availability of head space which is found to be inadequate, especially in front corner impacts on the occupant's side of the car, involving about 22° impact yaw.
Authors
- David C. Herbert - Traffic Accident Research Unit, Dept. of Motor Transport New South Wales, Australia
- John D. Stott - Traffic Accident Research Unit, Dept. of Motor Transport New South Wales, Australia
- Christopher W. Corben - Traffic Accident Research Unit, Dept. of Motor Transport New South Wales, Australia
Topic
Citation
Herbert, D., Stott, J., and Corben, C., "Head Space Requirements for Seat Belt Wearers," SAE Technical Paper 751164, 1975, https://doi.org/10.4271/751164.Also In
References
- “Australian Design Rules for Vehicle Safety” Australian Department of Transport
- Vaughan R.G. Wood R. Croft P.G. “Some aspects of compulsory seat belt wearing” Reprint 7th Conference Adelaide 1974 Australian Road Research Board
- Herbert D.C. Wyllie J.M. Corben C.W. “Side Impacts and Lap/Sash Belts” Department of Motor Transport New South Wales
- Henderson J.M. Freedman K. “The Effect of Mandatory Seat Belt Use in New South Wales, Australia” Department of Motor Transport New South Wales
- Vazey B.A. “In-Depth Analysis of Fatalities to Seat Belt Wearers” Department of Motor Transport New South Wales
- Patrick L.M. Andersson A. Bohlin N. “Three Point Harness Accident and Laboratory Data Comparison” 18th Stapp Car Crash Conference Society of Automotive Engineers Paper 741181 1974
- Henderson J.M. Wyllie J.M. “Seat Belts - Limits of Protection: a study of fatal injuries among belt wearers” 17th Stapp Car Crash Conference Society of Automotive Engineers Paper 730964 1973
- Patrick L.M. Trosien K.R. “Volunteer, Anthropometric Dummy, and Cadaver Responses with Three and Four Point Restraints” 1971 Automotive Engineering Congress Society of Automotive Engineers Paper 710079 1971
- Patrick L.M. “Comparison of Dynamic Response of Humans and Test Devices (Dummies)” Symposium on Human Impact Response October 1972 Plenum Press New York 1973
- Mertz H.J. Patrick L.M. “Investigation of the Kinematics and Kinetics of Whiplash” Eleventh Stapp Car Crash Conference Society of Automotive Engineers Paper 670919 1967
- Melvin J.W. McElhaney J.M. Roberts V.L. “Evaluation of Dummy Neck Performance” Symposium on Human Impact Response October 1972 Plenum Press New York 1973
- Hontschik H. Schmid I. “On the Survival Space Required by Occupants wearing Seat Belts” 1974 238 Milne R.J.H. Motor Industry Research Association
- Mertz H.J. Neathery R.F. Culver C.C. “Performance Requirements and Characteristics of Mechanical Necks” Symposium on Human Impact Response October 1972 Plenum Press New York 1973
- Mertz H.J. Patrick L.M. “Strength and Response of the Human Neck” 15th Stapp Car Crash Conference Society of Automotive Engineers Paper 710855 1971
- Haffner M.P. Cohen G.B. “Progress in the Mechanical Simulation of Human Head-Neck Response” Symposium on Human Impact Response October 1972 Plenum Press New York 1973
- Robbins D.H. Snyder R.G. Chaffin D.B. Foust D.R. “A Mathematical Study of the Effect of Neck. Physical Parameters on Injury Susceptibility” Proceedings of Automotive Engineering Congress Detroit February 1974 Society of Automotive Engineers Paper 742074 1974
- Robbins D.H. Snyder R.G. Roberts V.L. “Mathematical Simulation of Daisy Track Human Volunteer Tests” Final Report on NHTSA Contract No. FH-11-6962 1971
- Armstrong R.W. Waters H.P. “Testing Programs and Research on Restraint Systems” Proceedings of International Automotive Engineering Congress Detroit January 1969 Society of Automotive Engineers Paper 690247
- Armstrong R.W. Waters H.P. Stapp J.P. Human Muscular Restraint During Sled Deceleration” Society of Automotive Engineers Transactions 77 1969
- Chandler R.F. Christian R.A. “Crash Testing of Humans in Automobile Seats” reprinted 1970 from proceedings of International Safety Conference Compendium Society of Automotive Engineers New York 1970
- Mayor R.P. Naab K.N. “Basic Research in Automobile Crashworthiness - Testing and evaluation of Modifications for side Impacts' Cornell Aeronautical Laboratory Report No. YB-2864-V-3 Buffalo, New York 1969
- Herbert D.C. Stott J.D. Garth R. “Crash Performance of Emergency Locking Retractors” Department of Motor Transport New South Wales
- “Devices for Use in Defining and Measuring Motor Vehicle Seating Accommodation” SAE J826a, 1974 SAE Handbook Society of Automotive Engineers 1974